Hitachi CP-X255 user manual Before using the network functions…

Page 59

Network Functions

Before using the network functions…

To use the network functions of this projector, the projector must be configured to suit your network. Consult with your network administrator before connecting the projector to your network. Incorrect network configuration of this projector may cause problems on your network.

Connect to the Gateway (The router/PC that forwards traffic to a destination outside of the subnet of the transmitting device) from the network terminal on the projector using a CAT-5 cable and configure the following settings.

If using a network with DHCP enabled:

The projector’s network settings can be configured automatically. when [DHCP] on the network menu is set to [TURN ON]. Please refer to DHCP in network menu. (User's Manual - Operating Guide : NETWORK Menu) If a fixed / static IP address is required, please configure your projector according to the steps in the following section.

If using a network system that does not have DHCP enabled or if using a fixed IP address on a network system equipped with DHCP enabled:

Configure the following settings on the network menu.

(User's Manual - Operating Guide : NETWORK Menu)

1. [DHCP]: Disable DHCP (Set [DHCP] to [TURN OFF]).

2. [IP ADDRESS]: Enter an appropriate IP address for the projector to connect to your network.

3. [SUBNET MASK]: Enter an appropriate SUBNETMASK for the projector to connect to your network.

4. [DEFAULT GATEWAY]: Enter an appropriate Gateway (the router/PC that forwards traffic to a destination outside of the subnet of the transmitting device) address for the projector to connect to your network.

3

Image 59
Contents Trademark acknowledgment About this manualThank you for purchasing this projector Content About contents of package Fastening the lens cover Projector Part namesCR/PR ComponentCB/PB Magnify Remote controlControl buttons Setting up For the model CP-X255 ArrangementFor the model CP-S245 Adjusting the projectors elevator How to attach Using the Security BarAbout Plug-and-Play capability Connecting your devicesExamples of connection with a computer CB/PB Connecting to a monitor outputConnecting to a speaker with amplifier output Examples of connection with a VCR/DVD playerConnecting power supply Putting batteries Remote controlUsing the remote control Turning off the power Power on/offTurning on the power Temporarily muting the sound Adjusting the volumeSelecting an input signal Operating For a video signal/no signal 43  169  Small Searching an input signalAdjusting the zoom and focus Selecting an input signal For a video signal or s-video signal Using the automatic adjustment featureAdjusting the position  For an RGB signalCorrecting the keystone distortions Using the magnify featurePress the on button of Magnify on the remote control No operation, and the projector will enter the Magnify modeTemporarily blanking the screen Freezing the screenUSB mouse and keyboard control Available function Remote control operationOperating the computer screen Advanced Menu Multifunctional settingsUsing the menu function Easy MenuEasy Menu Filter Time ResetEasy Menu MirrorGamma Picture MenuSecam Picture MenuHigh  Middle  LOW  Custom Color TempSAVE4 SAVE3  SAVE2  SAVE1 TV  Film  Turn OFFProgressive LOAD1  LOAD2  LOAD3  LOAD4Position PhaseImage Menu Over ScanExecute Auto AdjustImage Menu SizeVideo Format Input MenuColor Space ComponentInformation Input MenuAudio Setup MenuVolume Bright  Dark Screen MenuMenu Position OSD BrightMyScreen Lock Screen MenuStart UP MyScreenNo Input is Detected MessageAuto OFF Reset  CancelOption Menu Auto SearchOption Menu IP Address Network MenuDhcp Network Menu Network Functions Refer to the separate volume on Network FunctionsLamp MaintenanceLamp Type number = DT00731 Case of replacement by yourselfLamp Type number = NJ22222 Air filterAir filtre Replacing Internal Clock battery Page Is out of the response parameter range of this unit There is no input signalInternal temperature is rising Related messagesRegarding the indicator lamps Regarding the indicator lamps Signal source does not correctly work Electrical power cord is not pluggedPower switch is not set to the on position Signal cables are not correctly connectedColor Space setting is not suitable Volume is adjusted to an extremely low levelAudio setting is not correct Color settings are not correctly adjustedLamp is approaching the end of its product Lifetime Not properly adjustedEither the focus and/or horizontal phase settings are Whisper function is workingAudio output SpecificationRGB input Video input Audio input Communication portSpecifications CP-S245/X255 only Still Image Transfer Failure & Warning Alerts via E-mailProjector Management via Snmp Controlling the Projector via SchedulingBefore using the network functions… Configuring and controlling the projector via a web browser Configuring and controlling the projector via a web browser Https//192.168.1.10 into SettingsNetwork Information Displays the Dhcp configuration settingsDhcp OFF Network SettingsDisplays and configures network settings Dhcp onClick the Apply button to save the settings Port SettingsDisplays and configures communication port settings Displays and configures e-mail addressing settings Mail SettingsDisplays and configures failure & warning alerts Alert SettingsAir Flow Error Alert SettingsLamp Error Temp ErrorFilter Error Lamp Time ErrorCool Error Lamp Time Alarm Other ErrorSchedule Execution Error Displayed Filter Time AlarmAuthentication Failure Change the Lamp isDisplays and configures schedule settings Schedule SettingsSchedule Setting Parameter Date/Time SettingsDisplays and configures the date and time settings Sntp Date/Time SettingsSnmp Security SettingsProjector Control Projector ControlProjector Control Displays and configures the current projector status Projector StatusDescription Restart Network RestartLogoff Restarts the projector’s network connectionExample If the IP address of the projector is set to Failure & Warning Alerts via E -mail10 Mail Settings Configure the following items via a web browser to use Snmp Snmp settingsProjector management via Snmp Controlling the Projector via Scheduling Date/Time setting can be adjusted via a web browser Date/Time Settings 18Schedule settings can be configured from a web browser Schedule Settings 16Following port is used for e-Shot TCP #9716 Shot Still Image Transfer SettingsShot Still Image Transfer Display Communication PortShot Still Image Transfer Transmission Shot Still Image Transfer SettingsCommand Control Settings 9 Command Control via the Network20 Command Control SettingsSend Data format Command formatReply Error code Header Data RS-232CcommandReply Data format Automatic Connection Break AuthenticationVesa Example of computer signalVesa Text Initial set signals Connection to the ports Except when set to RGB OUTComponent Video C Y, D CB/PB, E CR/PR LAN RJ-45 jack Audio 1-IN Ø3.5 stereo mini jack, I J Audio 2 L/R RCA jackRTS CTSRS-232C Communication Connecting the cableCommunications setting Increasing the projector setting value Increment command Requesting projector status Get commandChanging the projector settings Set command Using the projector default settings Reset CommandRS-232C Communication Be EF FB FA Color Temp Gain G Aspect Keystone Mute OSD Bright Greece