Hitachi CP-X255 user manual Network Menu, Dhcp, IP Address

Page 40

Multifunctional settings

NETWORK Menu

Select [Network] from the main menu to access the following functions.

 MENU [RGB]

 

:SELECT

 PICTURE

 DHCP

 TURN OFF

 IMAGE

 IP ADDRESS

 

 INPUT

 SUBNET MASK

 

 SETUP

 DEFAULT GATEWAY

 SCREEN

 DATE AND TIME

 

 OPTION

 TIME DIFFERENCE

 NETWORK

 e‑SHOT

 

 EASY MENU

 INFORMATION

 

NOTE • The factory default setting for DHCP is “TURN ON”. There is no need to set up [DHCP], [IP ADDRESS], [SUBNET MASK] or [DEFAULT GATEWAY] if your network

has DHCP enabled. (User’s Manual - Network Functions)

•If you are not utilizing SNTP (User’s Manual - Network Functions), then you must set the DATE AND TIME during the initial installation. Please refer to the item DATE AND TIME on the following list.

NOTE Consult with your network administrator before connecting to an existing access point on your network. Incorrect network settings on this projector may cause trouble on the network.

Item

Operation

 

DHCP

DHCP TURN ON/TURN OFF:

DHCP

Use the ▲/▼ buttons to turn DHCP on/off

TURN ON

(Dynamic Host

TURN OFF

TURN ON TURN OFF

 

Configuration

 

Select TURN OFF when the network does not have DHCP

Protocol)

enabled.

 

 

 

 

Entering the IP ADDRESS :

 

 

Use the ▲/▼/◄/► buttons to enter the IP

192. 168. 1. 254

 

ADDRESS. This function can only be used

IP ADDRESS

IP ADDRESS

when DHCP is set to “TURN OFF”.

 

~Note~

 

 

 

 

The IP ADDRESS is the number that identifies this projector on the

 

network. You cannot have two devices with the same IP ADDRESS

 

on the same network.

 

 

Entering the SUBNET MASK :

 

 

Use the buttons ▲/▼/◄/► to enter the

255. 255. 255. 0

SUBNET MASK same SUBNET MASK used by your PC.

SUBNET MASK

 

This function can only be used when DHCP

 

 

is set to “TURN OFF”.

 

40

Page 39 Page 41
Image 40
Page 39 Page 41
Contents Thank you for purchasing this projector About this manualTrademark acknowledgment Content About contents of package Fastening the lens cover Part names ProjectorCB/PB ComponentCR/PR Control buttons Remote controlMagnify Setting up For the model CP-S245 ArrangementFor the model CP-X255 Adjusting the projectors elevator Using the Security Bar How to attachConnecting your devices About Plug-and-Play capabilityExamples of connection with a computer Connecting to a monitor output Connecting to a speaker with amplifier outputExamples of connection with a VCR/DVD player CB/PBConnecting power supply Remote control Putting batteriesUsing the remote control Turning on the power Power on/offTurning off the power Adjusting the volume Selecting an input signalOperating Temporarily muting the soundSearching an input signal Adjusting the zoom and focusSelecting an input signal  For a video signal/no signal 43  169  SmallUsing the automatic adjustment feature Adjusting the position For an RGB signal  For a video signal or s-video signalUsing the magnify feature Press the on button of Magnify on the remote controlNo operation, and the projector will enter the Magnify mode Correcting the keystone distortionsFreezing the screen Temporarily blanking the screenOperating the computer screen Available function Remote control operationUSB mouse and keyboard control Multifunctional settings Using the menu functionEasy Menu Advanced MenuEasy Menu Reset Easy MenuMirror Filter TimePicture Menu GammaPicture Menu High  Middle  LOW  CustomColor Temp SecamTV  Film  Turn OFF ProgressiveLOAD1  LOAD2  LOAD3  LOAD4 SAVE4 SAVE3  SAVE2  SAVE1Phase Image MenuOver Scan PositionAuto Adjust Image MenuSize ExecuteInput Menu Color SpaceComponent Video FormatInput Menu InformationVolume Setup MenuAudio Screen Menu Menu PositionOSD Bright Bright  DarkScreen Menu Start UPMyScreen MyScreen LockMessage No Input is DetectedReset  Cancel Option MenuAuto Search Auto OFFOption Menu Dhcp Network MenuIP Address Network Menu Refer to the separate volume on Network Functions Network FunctionsLamp MaintenanceLamp Lamp Case of replacement by yourselfType number = DT00731 Air filter Type number = NJ22222Air filtre Replacing Internal Clock battery Page There is no input signal Internal temperature is risingRelated messages Is out of the response parameter range of this unitRegarding the indicator lamps Regarding the indicator lamps Electrical power cord is not plugged Power switch is not set to the on positionSignal cables are not correctly connected Signal source does not correctly workVolume is adjusted to an extremely low level Audio setting is not correctColor settings are not correctly adjusted Color Space setting is not suitableNot properly adjusted Either the focus and/or horizontal phase settings areWhisper function is working Lamp is approaching the end of its product LifetimeSpecification RGB input Video inputAudio input Communication port Audio outputSpecifications CP-S245/X255 only Failure & Warning Alerts via E-mail Projector Management via SnmpControlling the Projector via Scheduling Still Image TransferBefore using the network functions… Configuring and controlling the projector via a web browser Configuring and controlling the projector via a web browser Settings Https//192.168.1.10 intoDisplays the Dhcp configuration settings Network InformationNetwork Settings Displays and configures network settingsDhcp on Dhcp OFFDisplays and configures communication port settings Port SettingsClick the Apply button to save the settings Mail Settings Displays and configures e-mail addressing settingsAlert Settings Displays and configures failure & warning alertsAlert Settings Lamp ErrorTemp Error Air Flow ErrorCool Error Lamp Time ErrorFilter Error Schedule Execution Error Other ErrorLamp Time Alarm Filter Time Alarm Authentication FailureChange the Lamp is DisplayedSchedule Settings Displays and configures schedule settingsSchedule Setting Displays and configures the date and time settings Date/Time SettingsParameter Date/Time Settings SntpSecurity Settings SnmpProjector Control Projector ControlProjector Control Projector Status Displays and configures the current projector statusNetwork Restart LogoffRestarts the projector’s network connection Description Restart10 Failure & Warning Alerts via E -mailExample If the IP address of the projector is set to Mail Settings Projector management via Snmp Snmp settingsConfigure the following items via a web browser to use Snmp Controlling the Projector via Scheduling Date/Time Settings 18 Date/Time setting can be adjusted via a web browserSchedule Settings 16 Schedule settings can be configured from a web browserShot Still Image Transfer Settings Shot Still Image Transfer DisplayCommunication Port Following port is used for e-Shot TCP #9716Shot Still Image Transfer Settings Shot Still Image Transfer TransmissionCommand Control via the Network Command Control Settings 9Command Control Settings 20Command format Reply Error codeHeader Data RS-232Ccommand Send Data formatReply Data format Authentication Automatic Connection BreakVesa Text Example of computer signalVesa Initial set signals Except when set to RGB OUT Connection to the portsComponent Video C Y, D CB/PB, E CR/PR Audio 1-IN Ø3.5 stereo mini jack, I J Audio 2 L/R RCA jack RTSCTS LAN RJ-45 jackCommunications setting Connecting the cableRS-232C Communication Requesting projector status Get command Changing the projector settings Set commandUsing the projector default settings Reset Command Increasing the projector setting value Increment commandRS-232C Communication Be EF FB FA Color Temp Gain G Aspect Keystone Mute OSD Bright Greece
Top Page Image Contents