Hitachi CP-X255 user manual Power on/off, Turning on the power, Turning off the power

Page 17

Power on/off

Power on/off

WARNING ►When the power is on, a strong light is emitted. Do not look into the lens of projector. Also do not peep at the inside of projector through a hole.

NOTE • Turn the power on/off in right order. Please power on the projector prior to the connected devices. Power off the projector later than the connected devices.

Turning on the power

1. Make sure that the power cord is firmly and correctly connected to the projector and the

outlet.

STANDBY/ON

POWER

button

indicator

2. Remove the lens cover, and set the power switch to the ON position.

The power indicator will light up in steady orange. Then wait several seconds because the buttons may not function for these several seconds.

Press the STANDBY/ON button on the projector or the remote control.

3. The projector lamp will light up and the POWER

POWER

indicator will begin blinking in green. When the power is

(Steady orange)

completely on, the indicator will stop blinking and light in

POWER

green.

(Blinking in green)

To display the picture, select an input signal according to

 

the section "Selecting an input signal" (18).

POWER

 

Turning off the power

(Steady green)

This product is able to turn off the main power during the cooling. However, please pay special attention to below two points when you do:

(1)Please do not turn the projector on again for at least 1 minute in this case. Neglect could shorten the lifetime of the lamp.

(2)During use or immediately after use, do not touch around the lamp and vents of the projector (4 ) It could cause a burn.

1. Press the STANDBY/ON button on the projector or the remote control. The message "Power off?" will appear on the screen for approximately 5

seconds.

2. Press the STANDBY/ON button on the projector or the remote control again while the message appears.

The projector lamp will go off, and the POWER indicator will begin blinking in orange.

Power off?

POWER

Then the POWER indicator will stop blinking and light in steady orange when the lamp cooling is complete.

3. Make sure that the power indicator lights in steady orange, and set the power switch to the OFF position. The POWER

indicator will go off. Attach the lens cover.

(Blinking in orange) POWER (Steady orange)

17

Page 16 Page 18
Image 17
Page 16 Page 18
Contents Trademark acknowledgment About this manualThank you for purchasing this projector Content About contents of package Fastening the lens cover Projector Part namesCR/PR ComponentCB/PB Magnify Remote controlControl buttons Setting up For the model CP-X255 ArrangementFor the model CP-S245 Adjusting the projectors elevator How to attach Using the Security BarAbout Plug-and-Play capability Connecting your devicesExamples of connection with a computer Connecting to a speaker with amplifier output Connecting to a monitor outputExamples of connection with a VCR/DVD player CB/PBConnecting power supply Putting batteries Remote controlUsing the remote control Turning off the power Power on/offTurning on the power Selecting an input signal Adjusting the volumeOperating Temporarily muting the soundAdjusting the zoom and focus Searching an input signalSelecting an input signal  For a video signal/no signal 43  169  SmallAdjusting the position Using the automatic adjustment feature For an RGB signal  For a video signal or s-video signalPress the on button of Magnify on the remote control Using the magnify featureNo operation, and the projector will enter the Magnify mode Correcting the keystone distortionsTemporarily blanking the screen Freezing the screenUSB mouse and keyboard control Available function Remote control operationOperating the computer screen Using the menu function Multifunctional settingsEasy Menu Advanced MenuEasy Menu Easy Menu ResetMirror Filter TimeGamma Picture MenuHigh  Middle  LOW  Custom Picture MenuColor Temp SecamProgressive TV  Film  Turn OFFLOAD1  LOAD2  LOAD3  LOAD4 SAVE4 SAVE3  SAVE2  SAVE1Image Menu PhaseOver Scan PositionImage Menu Auto AdjustSize ExecuteColor Space Input MenuComponent Video FormatInformation Input MenuAudio Setup MenuVolume Menu Position Screen MenuOSD Bright Bright  DarkStart UP Screen MenuMyScreen MyScreen LockNo Input is Detected MessageOption Menu Reset  CancelAuto Search Auto OFFOption Menu IP Address Network MenuDhcp Network Menu Network Functions Refer to the separate volume on Network FunctionsLamp MaintenanceLamp Type number = DT00731 Case of replacement by yourselfLamp Type number = NJ22222 Air filterAir filtre Replacing Internal Clock battery Page Internal temperature is rising There is no input signalRelated messages Is out of the response parameter range of this unitRegarding the indicator lamps Regarding the indicator lamps Power switch is not set to the on position Electrical power cord is not pluggedSignal cables are not correctly connected Signal source does not correctly workAudio setting is not correct Volume is adjusted to an extremely low levelColor settings are not correctly adjusted Color Space setting is not suitableEither the focus and/or horizontal phase settings are Not properly adjustedWhisper function is working Lamp is approaching the end of its product LifetimeRGB input Video input SpecificationAudio input Communication port Audio outputSpecifications CP-S245/X255 only Projector Management via Snmp Failure & Warning Alerts via E-mailControlling the Projector via Scheduling Still Image TransferBefore using the network functions… Configuring and controlling the projector via a web browser Configuring and controlling the projector via a web browser Https//192.168.1.10 into SettingsNetwork Information Displays the Dhcp configuration settingsDisplays and configures network settings Network SettingsDhcp on Dhcp OFFClick the Apply button to save the settings Port SettingsDisplays and configures communication port settings Displays and configures e-mail addressing settings Mail SettingsDisplays and configures failure & warning alerts Alert SettingsLamp Error Alert SettingsTemp Error Air Flow ErrorFilter Error Lamp Time ErrorCool Error Lamp Time Alarm Other ErrorSchedule Execution Error Authentication Failure Filter Time AlarmChange the Lamp is DisplayedDisplays and configures schedule settings Schedule SettingsSchedule Setting Parameter Date/Time SettingsDisplays and configures the date and time settings Sntp Date/Time SettingsSnmp Security SettingsProjector Control Projector ControlProjector Control Displays and configures the current projector status Projector StatusLogoff Network RestartRestarts the projector’s network connection Description RestartExample If the IP address of the projector is set to Failure & Warning Alerts via E -mail10 Mail Settings Configure the following items via a web browser to use Snmp Snmp settingsProjector management via Snmp Controlling the Projector via Scheduling Date/Time setting can be adjusted via a web browser Date/Time Settings 18Schedule settings can be configured from a web browser Schedule Settings 16Shot Still Image Transfer Display Shot Still Image Transfer SettingsCommunication Port Following port is used for e-Shot TCP #9716Shot Still Image Transfer Transmission Shot Still Image Transfer SettingsCommand Control Settings 9 Command Control via the Network20 Command Control SettingsReply Error code Command formatHeader Data RS-232Ccommand Send Data formatReply Data format Automatic Connection Break AuthenticationVesa Example of computer signalVesa Text Initial set signals Connection to the ports Except when set to RGB OUTComponent Video C Y, D CB/PB, E CR/PR RTS Audio 1-IN Ø3.5 stereo mini jack, I J Audio 2 L/R RCA jackCTS LAN RJ-45 jackRS-232C Communication Connecting the cableCommunications setting Changing the projector settings Set command Requesting projector status Get commandUsing the projector default settings Reset Command Increasing the projector setting value Increment commandRS-232C Communication Be EF FB FA Color Temp Gain G Aspect Keystone Mute OSD Bright Greece
Top Page Image Contents