Hitachi CMP5000WXU, CMP5000WXJ Connection Panel, Operating range of the remote control unit

Page 14

Part Names and Functions

English

Part Names and Functions

Operating range of the remote control unit

When operating the remote control unit, point it at the remote sensor located on the front panel of the main unit. The remote control unit is operable up to 23 feet (7 m) from the unit and within a 30 angle on each side of the sensor.

7 m (23 feet)

30˚

30˚

Remote Sensor

If you are having difficulty with operation of the remote control unit

The remote control unit may not operate if there are objects placed between it and the display.

Operational distance will gradually become shorter as the batteries begin to wear out, replace weak batteries with new ones as soon as possible.

This unit discharges infrared rays from the screen. Placing a video deck or other component that is operated by an infrared remote control unit near this unit may hamper that component’s reception of the remote control’s signal, or prevent it from receiving the signal entirely. Should this occur, move the component to a position further away from this unit.

Depending on the installation surroundings, this unit’s remote control unit may be influenced by the infrared rays discharged from the plasma display, hampering reception of its rays or limiting its operational distance. The strength of infrared rays discharged from the screen will differ according to the picture displayed.

This remote control unit has been designed to operate this display unit only, and it cannot be used to operate other devices.

Connection Panel

The connection panel is provided with two video input jacks and one video output jack. Audio input and speaker output jacks are also provided.

For instructions regarding connections, consult the pages noted in parentheses by each item.

1SPEAKER (R) terminal

For connection of an external right speaker. Connect a speaker whose impedance is 8 -16 Ω

(page 12).

2CONTROL IN/OUT

DO NOT MAKE ANY CONNECTIONS TO THESE TERMINALS.

These terminals are used in the factory setup.

3COMBINATION IN/OUT

DO NOT MAKE ANY CONNECTIONS TO THESE TERMINALS.

These terminals are used in the factory setup.

4RS-232C

DO NOT MAKE ANY CONNECTIONS TO THIS TERMINAL.

This terminal is used in the factory setup.

5INPUT1 (mini D-sub 15 pin)

For connection of a personal computer (PC) or similar component. Make sure that the connection made corresponds to the format of the signal output from the connected component (pages 9 to 11).

6OUTPUT (INPUT1) (mini D-sub 15 pin)

Use the OUTPUT (INPUT1) terminal to output the video signal to an external monitor or other component.

Note: The video signal will not be output from the OUTPUT (INPUT1) terminal when the main power of this unit is off or in standby mode.

(page 10)

7INPUT2 (BNC jacks)

For connection of a personal computer (PC) or similar component. Make sure that the connection made corresponds to the format of the signal output from the connected component (pages 9 to 11).

6

En

Page 13 Page 15
Image 14
Page 13 Page 15
Contents CMP5000WXU Manuel Utilisateur CMP5000WXJ English Safety Guidelines Safety GuidelinesSafety Guidelines III FCC Federal Communications Commission Statement Warning USER’S Manual ¶ Introduces newly developed 50 XGA Wide Plasma Panel ¶ Supports wide range of computer signal formats¶ Power-Saving Design ¶ High reliability for commercial applicationsContents About operations in this manual How to Use This ManualBefore Proceeding Checking Supplied Accessories Main unit Part Names and FunctionsMain Unit Operation panel on the main unitWhen handling the remote control unit Remote Control UnitInserting the batteries Remote control unit Operating range of the remote control unit Connection PanelAudio Output Stereo mini jack ~ Speaker L terminalAudio Input Stereo mini jack Wall-mount installation of the unit Installation and ConnectionsInstallation of the Unit Rear view diagramConnection to INPUT1 and INPUT2 When connecting to INPUT2Installation and Connections Connection to a personal computerConnection of G on Sync analog RGB source When connecting to INPUT1When connecting to Output INPUT1 Connection of composite Sync analog RGB Source Connecting the speakersAudio Connections Making connections to the audio inputs on this unitPower Cord Connection AndInstallation How to Route CablesOrganize cables together using the provided speed clamps To attach the speed clamps to the main unitScreen Mode setup Setting Up the SystemSetup after Connection Setting Up the System Press 5/∞ to select Clamp Position Clamp Position setupSetup of Clamp Position Press SET to select LockedSelecting an Input Source Press STANDBY/ON to put this unit in the operation modeOperations Before you begin, make sure you havePress Display on the remote control unit To adjust the volumePress Volume on the remote control unit Press Muting on the remote control unitChanging the screen size During personal computer signal inputScreen Size Selection Press Screen Size to select the sizePartial Image Enlargement Management or Auto Power OFF mode Automatic Power OFFPress 5/∞ to select either the Power When using InputTo reset Picture mode settings to the default Display Panel AdjustmentsAdjusting the Picture Quality Adjusting the Image Position and Clock Automatic Adjustment Screen mode adjustment items To reset Screen mode settings to the defaultPress 2/3 to carry out the adjustment Press 2/3 to select ScreenOther Operations Other OperationsRewriting the Input Display Press SET to select Input LabelPress 2/3 to select Option Power Control FunctionPress SET to select Power Control Press MenuPress 5/∞ to select Audio OUT Audio Output Audio OUTOther Operations Press SET to select Input About the self diagnosis mode CleaningTroubleshooting Additional InformationGeneral problems Problems commonly mistaken as breakdownAdditional cautions STANDBY/ON indicatorPanel sticking and after-image lag General SpecificationsAccessories Input/outputInformation PC signal compatibilty table INPUT1, INPUT2Supplement AdditionalSupplement Explanation of Terms Pin No Input Output
Top Page Image Contents