Hitachi CMP5000WXU, CMP5000WXJ user manual Supplement Explanation of Terms, Pin No Input Output

Page 40

English

Additional Information

Supplement 2

Explanation of Terms

Signal assignment of INPUT 1 (Mini D-sub 15 pin

Aspect ratio

socket connector)

The TV screen’s width to height ratio is referred to as its aspect

 

ratio. The aspect ratio on standard TVs is 4:3 and on wide TVs or

 

High Definition TVs it is 16:9.

Additional Information

 

5

1

 

10

6

 

15

11

Pin No.

Input

Output

1

R or CR/PR

+

2

G or Y

+

3

B or CB/PB

+

4

NC (No connection)

+

5

GND

+

6

GND

+

7

GND

+

8

GND

+

9

DDC + 5V

NC (No connection)

10

GND

+

11

NC (No connection)

+

12

DDC SDA

NC (No connection)

13

HD or H/V SYNC

+

14

VD

+

15

DDC SCL

NC (No connection)

Apple and Macintosh are registered trademarks of Apple Computer, Inc.

Microsoft is a registered trademark of Microsoft Corporation. NEC and PC-9800 are trademarks of NEC Corporation.

VESA and DDC are registered trademarks of Video Electronics Standards Association.

Power Management and Sun Microsystems are registered trademarks of Sun Microsystems, Inc.

VGA and XGA are registered trademarks of International Business Machines Co., Inc.

ENERGY STAR is a U.S. registered mark.

G ON SYNC

This indicates a video signal in the form of a synchronization signal added to the G (GREEN) signal of the R.G.B signal.

VGA

VGA is short for “Video Graphics Array”.

Generally this indicates a 640 dot x 480 line resolution.

XGA

General term for “eXtended Graphics Array”.

Generally this indicates a 1024 dot x 768 line resolution.

32

En

Image 40
Contents CMP5000WXU Manuel Utilisateur CMP5000WXJ English Safety Guidelines Safety GuidelinesSafety Guidelines III FCC Federal Communications Commission Statement Warning USER’S Manual ¶ Supports wide range of computer signal formats ¶ Power-Saving Design¶ Introduces newly developed 50 XGA Wide Plasma Panel ¶ High reliability for commercial applicationsContents Before Proceeding How to Use This ManualAbout operations in this manual Checking Supplied Accessories Part Names and Functions Main UnitMain unit Operation panel on the main unitInserting the batteries Remote control unit Remote Control UnitWhen handling the remote control unit Operating range of the remote control unit Connection PanelAudio Input Stereo mini jack ~ Speaker L terminalAudio Output Stereo mini jack Installation and Connections Installation of the UnitWall-mount installation of the unit Rear view diagramWhen connecting to INPUT2 Installation and ConnectionsConnection to INPUT1 and INPUT2 Connection to a personal computerWhen connecting to Output INPUT1 When connecting to INPUT1Connection of G on Sync analog RGB source Connecting the speakers Audio ConnectionsConnection of composite Sync analog RGB Source Making connections to the audio inputs on this unitPower Cord Connection How to Route Cables Organize cables together using the provided speed clampsAndInstallation To attach the speed clamps to the main unitSetup after Connection Setting Up the SystemScreen Mode setup Clamp Position setup Setup of Clamp PositionSetting Up the System Press 5/∞ to select Clamp Position Press SET to select LockedPress STANDBY/ON to put this unit in the operation mode OperationsSelecting an Input Source Before you begin, make sure you haveTo adjust the volume Press Volume on the remote control unitPress Display on the remote control unit Press Muting on the remote control unitDuring personal computer signal input Screen Size SelectionChanging the screen size Press Screen Size to select the sizePartial Image Enlargement Automatic Power OFF Press 5/∞ to select either the PowerManagement or Auto Power OFF mode When using InputAdjusting the Picture Quality Display Panel AdjustmentsTo reset Picture mode settings to the default Adjusting the Image Position and Clock Automatic Adjustment To reset Screen mode settings to the default Press 2/3 to carry out the adjustmentScreen mode adjustment items Press 2/3 to select ScreenOther Operations Rewriting the Input DisplayOther Operations Press SET to select Input LabelPower Control Function Press SET to select Power ControlPress 2/3 to select Option Press MenuOther Operations Press SET to select Input Audio Output Audio OUTPress 5/∞ to select Audio OUT Cleaning TroubleshootingAbout the self diagnosis mode Additional InformationGeneral problems Problems commonly mistaken as breakdownPanel sticking and after-image lag STANDBY/ON indicatorAdditional cautions Specifications AccessoriesGeneral Input/outputPC signal compatibilty table INPUT1, INPUT2 SupplementInformation AdditionalSupplement Explanation of Terms Pin No Input Output