Hitachi CMP5000WXJ, CMP5000WXU Audio Connections, Connection of composite Sync analog RGB Source

Page 19

Installation and Connections

Connection of composite SYNC analog RGB

source

Make composite SYNC connections for a personal computer with output that has the vertical synchronization signal layered on top of the horizontal synchronization signal.

When connecting to INPUT1

 

 

 

 

INPUT1

OUTPUT

 

ANALOG RGB

 

 

(ANALOG RGB)

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Audio Connections

Before making connections, be sure to check that the audio component’s power and the unit’s main power is off.

Connecting the speakers

This unit is equipped with speaker output jacks for connection to the speaker system (not supplied) specially designed for use with this unit. Refer to the illustrations below when making connections to the speaker terminals on this unit.

Twist exposed wire strands together.

Push tab to the open position, and insert the wire. Then, close tab firmly to secure the wire in place.

English

On-screen setup is necessary after connection. Please see pages 14 and 15.

When connecting to INPUT2

(ON SYNC)

 

INPUT2

(H/V SYNC)

 

G

B

R

HD

VD

75Ω Ô2.2kΩ

When using INPUT2, set the impedance selector switch to match the output impedance of the connected computer’s synchronization signal.

When the output impedance of the computer’s synchronization signal is below 75 Ω , set this switch to the 75 Ω position.

On-screen setup is necessary after connection. Please see pages 14 and 15.

Notes

÷When making composite SYNC connections, do not connect anything to the VD jack. If connected, the picture may not be displayed properly.

÷On some types of Macintosh® components, G ON SYNC and composite SYNC are both output. With this type of component, please connect using the G ON SYNC connection (see page 10).

Note

When making speaker connections, be sure to match the polarities (+ and –) of the speaker terminals on this unit and the corresponding terminals on the speakers. If the polarity is reversed, the sound will be unnatural and lack bass.

Making connections to the audio inputs on this unit

This unit features two audio inputs and one audio output. The following chart shows the video inputs and the corresponding audio input jacks.

Video

Audio input jacks

Sound output

input

 

 

 

 

 

INPUT1

 

Sound of the selected video

Stereo mini jack

input is output from the

 

INPUT2

(L/R)

• SPEAKER terminals

 

• Stereo mini jacks (L/R).

 

 

 

 

 

Audio connections for component (computer) connected to INPUT 1 or INPUT 2

 

 

AUDIO

VD

 

INPUT OUTPUT

 

75Ω Ô2k.Ω2

(INPUT1/2)

 

 

Audio input to the AUDIO INPUT jacks (stereo mini jack) is possible for a

component connected to either INPUT1 or INPUT2. Sound is output from both the AUDIO OUTPUT jacks (stereo mini jack) and the SPEAKER terminals according to the video input selection.

Installation and Connections

11

En

Page 18 Page 20
Image 19
Page 18 Page 20
Contents CMP5000WXU Manuel Utilisateur CMP5000WXJ English Safety Guidelines Safety GuidelinesSafety Guidelines III FCC Federal Communications Commission Statement Warning USER’S Manual ¶ High reliability for commercial applications ¶ Supports wide range of computer signal formats¶ Power-Saving Design ¶ Introduces newly developed 50 XGA Wide Plasma PanelContents Before Proceeding How to Use This ManualAbout operations in this manual Checking Supplied Accessories Operation panel on the main unit Part Names and FunctionsMain Unit Main unitInserting the batteries Remote control unit Remote Control UnitWhen handling the remote control unit Connection Panel Operating range of the remote control unitAudio Input Stereo mini jack ~ Speaker L terminalAudio Output Stereo mini jack Rear view diagram Installation and ConnectionsInstallation of the Unit Wall-mount installation of the unitConnection to a personal computer When connecting to INPUT2Installation and Connections Connection to INPUT1 and INPUT2When connecting to Output INPUT1 When connecting to INPUT1Connection of G on Sync analog RGB source Making connections to the audio inputs on this unit Connecting the speakersAudio Connections Connection of composite Sync analog RGB SourcePower Cord Connection To attach the speed clamps to the main unit How to Route CablesOrganize cables together using the provided speed clamps AndInstallationSetup after Connection Setting Up the SystemScreen Mode setup Press SET to select Locked Clamp Position setupSetup of Clamp Position Setting Up the System Press 5/∞ to select Clamp PositionBefore you begin, make sure you have Press STANDBY/ON to put this unit in the operation modeOperations Selecting an Input SourcePress Muting on the remote control unit To adjust the volumePress Volume on the remote control unit Press Display on the remote control unitPress Screen Size to select the size During personal computer signal inputScreen Size Selection Changing the screen sizePartial Image Enlargement When using Input Automatic Power OFFPress 5/∞ to select either the Power Management or Auto Power OFF modeAdjusting the Picture Quality Display Panel AdjustmentsTo reset Picture mode settings to the default Adjusting the Image Position and Clock Automatic Adjustment Press 2/3 to select Screen To reset Screen mode settings to the defaultPress 2/3 to carry out the adjustment Screen mode adjustment itemsPress SET to select Input Label Other OperationsRewriting the Input Display Other OperationsPress Menu Power Control FunctionPress SET to select Power Control Press 2/3 to select OptionOther Operations Press SET to select Input Audio Output Audio OUTPress 5/∞ to select Audio OUT Additional Information CleaningTroubleshooting About the self diagnosis modeProblems commonly mistaken as breakdown General problemsPanel sticking and after-image lag STANDBY/ON indicatorAdditional cautions Input/output SpecificationsAccessories GeneralAdditional PC signal compatibilty table INPUT1, INPUT2Supplement InformationPin No Input Output Supplement Explanation of Terms
Top Page Image Contents