Hitachi CMP5000WXU, CMP5000WXJ user manual Specifications, General, Input/output, Accessories

Page 38

Additional Information

English

Specifications

General

Light emission panel	............	50 inch plasma display panel
Number of pixels		1280 x 768
Power supply		AC 100 - 120 V, 50/60 Hz
Rated current		3.8 A - 3.1A
Standby power consumption		...................................... 1 W
External dimensions	1218 (W) x 714 (H) x 98 (D) mm
............................. 47-31/32 (W) x 28-1/8 (H) x 3-7/8 (D) in.
Weight		38.9 kg (85 lbs. 12 oz)

Input/output

Video

Audio
Input	AUDIO INPUT (for INPUT 1/2)
	Stereo mini jack
	L/R ... 500mVrms/more than 10 kΩ

Output AUDIO OUTPUT Stereo mini jack

L/R ... 500mVrms (max)/less than 5 kΩ

SPEAKER

L/R ... 8 – 16 Ω /2W +2W (at 8 Ω )

Control

RS-232C ... D-sub 9 pin (pin connector)

COMBINATION IN/OUT

... Mini DIN 6 pin (x2)

CONTROL IN/OUT ... monaural mini jack (x2)

INPUT 1

Input Mini D-sub 15 pin (socket connector) RGB signal (G ON SYNC compatible) RGB ... 0.7 Vp-p/75 Ω /no sync. HD/CS, VD ... TTL level

/positive and negative polarity /2.2 kΩ

G ON SYNC

... 1 Vp-p/75 Ω /negative sync. *Compatible with Microsoft’s Plug & Play

(VESA DDC1/2B)

Accessories
Power cord	1
Remote control unit	1
AA (R6) batteries	2
Speed clamps	2
Bead bands	2
USER’S MANUAL	1

÷Due to improvements, specifications and design are subject to change without notice.

Additional Information

Output	Mini D-sub 15 pin (socket connector)
	75 Ω /with buffer
INPUT 2
Input	BNC jack (x5)
	RGB signal (G ON SYNC compatible)
	RGB ... 0.7 Vp-p/75 Ω /no sync.
	HD/CS, VD ... TTL level
	/positive and negative polarity/
	75 Ω or 2.2 kΩ
	(impedance switch)
	G ON SYNC ...
	1 Vp-p/75 Ω /negative sync.

30

En

Image 38

Contents CMP5000WXU Manuel Utilisateur CMP5000WXJ English Safety Guidelines Safety GuidelinesSafety Guidelines III FCC Federal Communications Commission Statement Warning USER’S Manual ¶ Introduces newly developed 50 XGA Wide Plasma Panel ¶ Supports wide range of computer signal formats¶ Power-Saving Design ¶ High reliability for commercial applicationsContents About operations in this manual How to Use This ManualBefore Proceeding Checking Supplied Accessories Main unit Part Names and FunctionsMain Unit Operation panel on the main unitWhen handling the remote control unit Remote Control UnitInserting the batteries Remote control unit Operating range of the remote control unit Connection PanelAudio Output Stereo mini jack ~ Speaker L terminalAudio Input Stereo mini jack Wall-mount installation of the unit Installation and ConnectionsInstallation of the Unit Rear view diagramConnection to INPUT1 and INPUT2 When connecting to INPUT2Installation and Connections Connection to a personal computerConnection of G on Sync analog RGB source When connecting to INPUT1When connecting to Output INPUT1 Connection of composite Sync analog RGB Source Connecting the speakersAudio Connections Making connections to the audio inputs on this unitPower Cord Connection AndInstallation How to Route CablesOrganize cables together using the provided speed clamps To attach the speed clamps to the main unitScreen Mode setup Setting Up the SystemSetup after Connection Setting Up the System Press 5/∞ to select Clamp Position Clamp Position setupSetup of Clamp Position Press SET to select LockedSelecting an Input Source Press STANDBY/ON to put this unit in the operation modeOperations Before you begin, make sure you havePress Display on the remote control unit To adjust the volumePress Volume on the remote control unit Press Muting on the remote control unitChanging the screen size During personal computer signal inputScreen Size Selection Press Screen Size to select the sizePartial Image Enlargement Management or Auto Power OFF mode Automatic Power OFFPress 5/∞ to select either the Power When using InputTo reset Picture mode settings to the default Display Panel AdjustmentsAdjusting the Picture Quality Adjusting the Image Position and Clock Automatic Adjustment Screen mode adjustment items To reset Screen mode settings to the defaultPress 2/3 to carry out the adjustment Press 2/3 to select ScreenOther Operations Other OperationsRewriting the Input Display Press SET to select Input LabelPress 2/3 to select Option Power Control FunctionPress SET to select Power Control Press MenuPress 5/∞ to select Audio OUT Audio Output Audio OUTOther Operations Press SET to select Input About the self diagnosis mode CleaningTroubleshooting Additional InformationGeneral problems Problems commonly mistaken as breakdownAdditional cautions STANDBY/ON indicatorPanel sticking and after-image lag General SpecificationsAccessories Input/outputInformation PC signal compatibilty table INPUT1, INPUT2Supplement AdditionalSupplement Explanation of Terms Pin No Input Output