Hitachi CP-X885W, CP-X880W user manual Lamp, Replacing the lamp

Page 29

THE LAMP (continued)

Replacing the lamp

All projector lamps will wear out eventually. If used for long periods of time, the image could become darkened, and the color contrast could be impacted as well. We recommend that you replace your lamps early. If the LAMP indicator turns red, or a message prompts you to replace the lamp when you power up the projector, the lamp needs to be replaced. (See "Related Messages" (Vol.2 8 ) and "Regarding the Indicator Lamps" (Vol.2 9 ) for details.)

1

Turn off the projector, and unplug the

power cord. Allow the lamp bulb to cool

 

for at least 45 minutes, and prepare a

 

new lamp (serial number: DT00531)

 

 

 

 

2

After making sure that the projector has

cooled adequately, slide the knob of a

lamp cover lock as shown in the figure. Then, one side of the lamp cover is raised. Pull up the lamp cover and remove it, as shown in the figure

Knob of Lamp

Cover Lock

4

Insert the new lamp, and

tighten the 3 screws firmly to

 

lock it in place

 

 

 

 

5

Interlocking the 2 tabs of the

lamp cover to the projector,

put the lamp cover on the projector.

Then push the point of the lamp cover to fix it, as shown in the figure.

Make sure that the lamp cover does’t come up

Tabs

3

Unscrew the 3 screws, and slowly pull

out the lamp by the handle

•Be careful not to touch the inside of the lamp case.

 

Push

6

Turn on the projector power,

and reset the lamp timer

• To reset the lamp timer, from the OPTION menu, select the LAMP TIME. (Vol.2 7 )

ATTENTION • Make sure that the screws are screwed in firmly. Loose screws could result in damage or injury.

•Do not use with lamp cover removed.

•Do not reset the lamp timer without replacing the lamp. Reset the lamp timer always when replacing the lamp. The message functions will not operate properly if the lamp timer is not reset correctly.

•When the lamp has been replaced after the message of “CHANGE THE LAMP .....THE POWER WILL TURN OFF AFTER 0 hr.” is displayed, or the LAMP indicator is red, complete the following operation within 10 minutes of switching power on.

NOTE • The LAMP indicator is also red when the lamp unit reaches high temperature. Before replacing the lamp, switch power off, wait approximately 20 minutes, and switch power on again. If the LAMP indicator is still red, replace the lamp.

28

Page 28 Page 30
Image 29
Page 28 Page 30
Contents CP-X880W / CP-X885W Contents Power cord Projector FeaturesSoft carrying case Remote control US Type UK Type Europe Type Projector With Lens CapDevices you will be using to the projector Only use the power cord that came with the projectorPart Names Remote Control Adjusting the Projectors Elevator Feet Setting UP the ProjectorPress and hold in the elevator Buttons Turn the elevator screw to fine tuneTop view Side view Adjusting the Screen Size and Projection DistanceScreen Connecting Your Devices Function Projector Port Connection Cables Ports and CablesConnecting to a Computer Connecting Your DevicesA a a BNC Input DVI InputConnecting to a Display Monitor Connecting to a DVD PlayerConnecting to a VCR Putting batteries into the remote control unit Using the Remote ControlRemove the battery cover Close the battery coverOperating the remote control Using the Remote ControlRemote control in an area free from obstacles Meters with a 40-degree rangeTurning on the Power Selecting an Input Signal Turning on the PowerTurning OFF the Power Press the Volume button Adjusting the VolumeUse the lever switch / to adjust the volume Temporarily Muting the SoundPress the Position button Adjusting the PositionUse the , , , buttons to adjust the position Automatic Adjustment for RGB Input Using the Automatic Adjustment FeatureAutomatic Adjustment for Video Input Press the Auto buttonPress the Keystone button Correcting Keystone DistortionsAs illustrated on the right, a dialog will appear On the screen to aid you in correcting the distortionFreezing the Screen Using the Magnify FeatureWas begun When BNC RGB is selected Adjusting Screen with ONE-TOUCHPress the ONE Touch button You can activate the following functions just byTemporarily Blanking the Screen Selecting the Aspect RatioPress the Aspect button Press the Blank buttonPress the Menu button Using the Menu FunctionsUse the lever switch To adjust the level Operating the PC Screen Available Functions Remote Control OperationDo not use the projector with the lamp cover removed High Voltage High Temperature High PressureLamp Replacing the lamp LampCaring for the air filter AIR FilterReplacing the air filter AIR FilterOther Care Caring for the cabinet and remote control transmitterCaring for the inside of the projector Caring for the lensFor Technical see the end of this manual Main Menu Multifunctional SettingsMain Menu Item selectionPICTURE-2 Menu PICTURE-1 MenuPICTURE-1 Menu PICTURE-2 MenuInput Menu Multifunctional SettingsInput Menu Auto Menu Auto MenuScreen Menu Screen MenuOption Menu Wireless MenuOption Menu Related Messages Power Lamp Temp Regarding the Indicator LampsVol.2-2 Phenomena That May Easily Be Mistaken for Machine DefectsVol.2-3 Vol.2-7Dimension Diagram SpecificationsSpecification Unit mmWarranty and AFTER-SERVICE Signal Terminal Specification Signal Connector PIN AssignmentRGB in 1/2 Sub 15-pin ShrinkResolution FH kHz FV Hz Rating Signal mode Display mode Example of Computer SignalInitial SET Signals ADB Mouse Connection to the Mouse ControlUSB Mouse PS/2 MouseConsist of header 7 bytes + command data 6 bytes Command dataRS-232C Communication ProtocolRS-232C Communication C4 D3 Command data chartBe EF BA D2 Be EF AD D0 Be EF CB D0 Regulatory Notices Hitachi Sales Europe GmbH Hitachi Europe GmbHHitachi Business Systems Nordic Hitachi France
Related manuals
Manual 56 pages 57.71 Kb

CP-X880W, CP-X885W specifications

The Hitachi CP-X885W and CP-X880W projectors are powerful and versatile projection solutions tailored for educational and corporate environments. Known for their reliability and superior performance, both models deliver high-quality visuals with a focus on user-friendly operations.

One of the outstanding features of the CP-X885W and CP-X880W is their brightness, rated at 3,600 ANSI lumens. This level of brightness allows the projectors to function effectively in a variety of lighting conditions, ensuring that presentations and videos are visible even in well-lit rooms. The native WXGA resolution (1280x800) contributes to sharp, detailed images, making these projectors ideal for displaying presentations, videos, and high-resolution graphics.

In terms of connectivity, the CP-X885W and CP-X880W offer a comprehensive range of options. They feature multiple input ports, including HDMI, USB, and VGA, allowing users to connect various devices such as laptops, Blu-ray players, and document cameras seamlessly. The inclusion of a USB port enables direct access to files, enhancing convenience for users who want to project without needing a computer.

Both projectors come equipped with Hitachi's innovative technologies, such as the Image Optimizer, which automatically adjusts the image quality based on the content being displayed. This ensures that pictures are vibrant, with accurate colors and sharp details, regardless of the source material. Additionally, the incorporation of a sophisticated lamp technology results in an impressive lamp life of up to 5,000 hours in normal mode, minimizing maintenance needs and reducing total cost of ownership.

The CP-X885W and CP-X880W models also prioritize ease of use and installation. They feature a 1.6x optical zoom lens, allowing for flexibility in setup, as users can project large images from various distances. The projectors are designed with lightweight and compact form factors, making them easy to transport and mount.

In conclusion, the Hitachi CP-X885W and CP-X880W offer an impressive combination of brightness, resolution, connectivity options, and innovative features, making them suitable for diverse environments. Whether in a classroom or a conference room, these projectors stand out as reliable tools for effective visual communication.
Top Page Image Contents