NEC VT45 user manual Cleaning or Replacing the Filters

Page 37

5.After you install a new lamp, select [Advanced Menu] [Projector Options][Setup][Page 4][Clear Lamp Hour Meter] to reset the lamp usage hours.

NOTE: When the lamp exceeds 1100 hours (up to 2100 hours in Eco 2 mode and up to 1600 hours in Eco 1 mode) of service, the projector cannot turn on and the menu is not displayed. If this happens, press the Help button on the remote control for a mini- mum of 10 seconds while in standby mode. When the lamp time clock is reset to zero, the STATUS indicator goes out.

To replace the air-filter:

1.Remove the filter cover by pushing up on the catch of the cover until you feel it detach.

L

E

Cleaning or Replacing the Filters

The air-filter sponge keeps the inside of the VT45 Projector free from dust or dirt and should be cleaned after every 100 hours of operation (more often in dusty conditions). If the filter is dirty or clogged, your projector may overheat.

CAUTION

Turn off the power and unplug the projector before replacing the filter.

Only clean the outside of the filter cover with a vacuum cleaner.

Do not attempt to operate the projector without a filter cover.

Your projector will not operate unless the filter cover is installed correctly.

To clean the air-filter:

When “Clean Filter” option is turned on, the “Please clean the filters” message will be displayed each time the projector is turned on after it has been used in excess of 100 hours. Should this message appear, clean the filters.

The message can be turned on or off using the “Menu” - “Fil- ter Clean Message” option on the Setup menu. See page E- 33.

After cleaning the filters and resetting the filter usage time back to zero, the message will not be displayed.

See page E-35 for resetting the filter usage time.

Vacuum the filter-through the filter cover.

L

E

2. Reinstall the new filter cover.

NOTE: Do not detach the sponge from the filter cover. Do not wash the filter cover with soap and water. Soap and water will damage the the filter membrane. Before replacing the filter cover, remove dust and dirt from the projector cabinet. Keep out dust and during filter replacement.

NOTE: When you replace the lamp, it is also wise to replace the filters. The filters come in the same package with your replace- ment lamp.

NOTE: A mix-up between the two filter covers can cause a dam- age to the projector.

The front and the side filter covers appear to be the same shape, but they are not interchangeable with each other.

E–37

Image 37
Contents VT45 LCD Projector User’s Manual Important Information PrecautionsInstallation Important SafeguardsPower Supply CleaningFire and Shock Precautions Lamp ReplacementTable of Contents Introduction Features you’ll enjoyIntroduction to the VT45 Projector Getting StartedWhats in the Box? ManualUsersRear / Side Features Getting to Know Your VT45 Projector Front / Side FeaturesUsing the protective lens pad Bottom / Side FeaturesTop Features Terminal Panel Features Remote Control Remote Control FeaturesRemote Control Precautions Operating Range Remote Control Battery InstallationSetting up Your Projector InstallationUsing a Tabletop or Cart Using the Lens ShiftLens Offset 4mm Distance ChartScreen inch Reflecting the Image Ceiling InstallationDocument Camera Wiring DiagramSignal cable supplied Connecting Your PCIBM VGA or Compatibles Audio cableMacintosh Notebook type Connecting Your Macintosh ComputerMacintosh Desktop type To connect to a Macintosh, simplyConnecting an External Monitor DVD player Connecting Your DVD PlayerAudio Equipment Component video cable RCA3VCR/ Laser disc player Connecting Your VCR or Laser Disc PlayerAudio equipment Document cameraGeneral Controls OperationTo select a menu language, follow these steps About Startup screen Menu Language Select screenGeometrical correction Enlarging and Moving a PictureShifting Image Position Adjusting the Tilt Foot Using the MenusBasic/ Advanced Menu Menu TreeSub Menu ItemsTitle bar Tab Highlight Menu ElementsMenu Descriptions & Functions VolumeSource Select PictureAdvanced Options Advanced mode Lamp ModePosition/ Clock when Auto Adjust is off Factory DefaultColor Management User AdjustProjector Options Keystone Bar option SetupPhase To lock the cabinet buttons InformationReplacing the Lamp MaintenanceTo replace the lamp Cleaning or Replacing the Filters Power/ Status Light Messages TroubleshootingCommon Problems & Solutions Problem Check These ItemsElectrical SpecificationsMechanical VT45 Cabinet DimensionsPin No RGB Signal Analog YCbCr Signal Mini D-Sub 15 Pin ConnectorSub Pin Assignments Timing Chart Cable Connection PC Control CodesCommunication Protocol To RxD of PC