Fluke 875 manual Applicable Drawings and Bill of Materials, Document Number Description

Page 47

Appendix	C
Applicable Drawings and Bill of Materials

Appendix C

Applicable Drawings and Bill of Materials

C.1 Applicable Drawings

Document Number	Description
GEL876-1-55	Rack Chassis & Recommended Seismic Mtg.
GEL876A-1	Readout Module Dimensional Outline
GEL875-1	Interconnection Diagram High-Range Containment Monitor
GEL-877-1	High-Range Detector & Bracket Dimensional Outline
876-1-114	Support Strap
844-8-5	Blank Panel Assembly
876-1-55	Rack Chassis
876A-1-108	High Range Containment Monitor Readout Assembly
876A-1-86	Preamp/Meter PC Board Assembly
876-1-100	Preamp Shield Assembly
876A-1-3E	Schematic Preamp Meter PC Board
876A-1-92	High-Range CAM ECS PC Board Assembly
876A-1-3D	Schematic ECS PC Board
876-1-89	Power Supply PC Board Assembly
876-1-3C	Schematic Power Supply PC Board Assembly
876-1-89A	Voltage Regulator PC Board Assembly
876-1-93A	Schematic, Regulator PC Board Assembly
876A-1-75A	Relay Driver PC Board Assembly
876A-1-3B	Schematic Relay Driver PC Board
876-1-104	Switch PC Board Assembly
876-1-3J	Schematic PC Switch Board
876-1- 78	Mother PC Board Assembly
876-1-3A	Schematic Mother PC Board

Document Number	Description
876-1-107	Rear Panel Assembly
876-1-85	Rear Panel Assembly

C-1

Image 47

Contents High Range Containment Monitor VictoreenFluke Biomedical Table of Contents Calibration and Test Procedures Containment Monitor SpecificationsIntroduction General DescriptionReadout Module 876A-1 Temperature Operating 40 to 120F 4 to 49CRack Chassis Equipment OverviewHigh-Range Containment Monitor Detector Optional Equipment Pull Box AssemblyCables/Connectors/Panel Flexible Tubing 878-12-30TABHigh-Range Containment Monitor Typical Energy Response Curve Detector Typical Linearity Detector Receiving Inspection High-Range Detector, Recommended InstallationStorage Procedures, Warnings, and CautionsBlank Pull Box InstallationInstallation Readout ModuleCable Sealing Specifications for CableDetector Cable Inside Containment Cable and Wiring InstallationDetector Test After Installation Specifications for CableComputer & Recorder Ancillary WiringAll Alarms on P2 Normal Operation Shelf State Power Connections P1Operation OperationVictoreen Readout Module 876A-1 Function DescriptionFunctional Description Negative Power Supply Operation of High Voltage Supply During ECS Test High Voltage Power Supply Normal Operation non-ECS TestFAIL/SAFE Comparison Circuit on Power Supply Board Alert Alarm Circuit High Alarm CircuitPen Clamp Fail/Safe CircuitRecorders and Computer Buffers Meter at extreme lower end of scale Panel Meter Action During ECS TestMonitoring Circuits of The ECS Board Action of Green Safe/Reset Light and Alarm During ECS TestLow Voltage Ramp Generator Block Diagram of ECS Test Muting Circuits of ECS Board Safe/Reset Sub-circuitsBlank Calibration Maintenance, Calibration, and TroubleshootingMaintenance Test Procedure TP876A-1-108 Troubleshooting Rear Panel Signal Input CircuitMother Board P/N 876-1-78, Schematic 876-1-3A PreamplifierIMeter Board P/N 876A-1-86, Schematic 876A-1-3ETest Point Normal Channel Test TP501 TP502 +6.3Normal Low Signal Level Channel Test High Alarm CircuitMuting Stages of the Alarm Circuits ESC Board P/N 876A-1-92, Schematic 876A-1-3D Wave Shapes on the Electronic Check Source Board Starting With Terminal H on Relay Driver Board Starting With Pins M and P on the Power Supply SchematicOverall Fail Circuitry Associated with the ECS Test Operation of the Latch Circuit Outputs of U206 Pulse Generator on the ECS BoardCircuit assumed initially in Pass Condition Fail Condition Latch CircuitPin Voltage State Comments NORCalibration and Test Procedures Blank Cable and Pull Box Procedures Cable and Pull Box ProceduresVictoreen Document Number Description Applicable Drawings and Bill of MaterialsApplicable Drawings Detector Cable Out of Containment Applicable Bill of Materials Fluke Biomedical