Emerson CW manual Electrical Specifications, Electrical data-50 Hz systems, Ir/Sgh

Electrical Specifications

7.0ELECTRICAL SPECIFICATIONS

Table 5	Electrical data—50 Hz systems
Reheat Options				Electric			None				Electric			None
Humidifier Options				IR/SGH			IR/SGH			Steam or None			Steam or None
Models	Motor HP	Volts	200	230	380-415	200	230	380-415		200	230	380-415	200	230	380-415
CW026	2.0	FLA	46.7	43.4	24.3	19.8	17.2		9.9	33.9	32.3	17.9	7.0	6.1		3.5
	3.0	FLA	49.8	46.1	25.9	22.9	19.9		11.5	37.0	35.0	19.5	10.1	8.8		5.1
CW038	3.0	FLA	62.9	59.0	33.2	22.9	19.9		11.5	50.1	47.9	26.8	10.1	8.8		5.1
	5.0	FLA	68.6	63.9	36.0	28.6	24.8		14.3	55.8	52.8	29.6	15.8	13.7		7.9
CW041	3.0	FLA	62.9	59.0	33.2	22.9	19.9		11.5	50.1	47.9	26.8	10.1	8.8		5.1
	5.0	FLA	68.6	63.9	36.0	28.6	24.8		14.3	55.8	52.8	29.6	15.8	13.7		7.9
CW051	5.0	FLA	94.6	88.4	49.6	41.2	35.9		20.7	69.2	66.2	36.8	15.8	13.7		7.9
	7.5	FLA	103.9	96.5	54.2	50.5	44.0		25.3	78.5	74.3	41.4	25.1	21.8		12.5
CW060	5.0	FLA	107.9	101.4	56.8	41.2	35.9		20.7	82.5	79.2	44.0	15.8	13.7		7.9
	7.5	FLA	117.2	109.5	61.4	50.5	44.0		25.3	91.8	87.3	48.6	25.1	21.8		12.5
CW076	7.5	FLA	126.6	122.6	68.6	50.5	44.0		25.3	101.2	100.4	55.8	25.1	21.8		12.5
	10.0	FLA	131.7	128.4	71.2	55.6	49.8		27.9	106.3	106.2	58.4	30.2	27.6		15.1
CW084	7.5	FLA	126.6	122.6	68.6	50.5	44.0		25.3	101.2	100.4	55.8	25.1	21.8		12.5
	10.0	FLA	131.7	128.4	71.2	55.6	49.8		27.9	106.3	106.2	58.4	30.2	27.6		15.1
	10.0	FLA	131.7	128.4	71.2	55.6	49.8		27.9	106.3	106.2	58.4	30.2	27.6		15.1
CW106
	15.0	FLA	147.1	142.4	78.9	71.0	63.8		35.6	121.7	120.2	66.1	45.6	41.6		22.8
	20.0	FLA	161.5	152.8	86.1	85.4	74.2		42.8	136.1	130.6	73.3	60.0	52.0		30.0
	10.0	FLA	131.7	128.4	71.2	55.6	49.8		27.9	106.3	106.2	58.4	30.2	27.6		15.1
CW114
	15.0	FLA	147.1	142.4	78.9	71.0	63.8		35.6	121.7	120.2	66.1	45.6	41.6		22.8
	20.0	FLA	161.5	152.8	86.1	85.4	74.2		42.8	136.1	130.6	73.3	60.0	52.0		30.0

1.FLA = FULL LOAD AMPS

2.Amperage requirements are based on the rated max FLA current of each component in the unit. The rated max FLA current of the unit is not the sum total of all components, but is the total of the components which operate during maximum electrical load conditions.

3.The values in the table are for power demand of the unit only.

4.Units are 3-phase, 50-cycle.

5.Consult factory engineering department for electrical requirements of units with variations not listed above.

Table 6	Indoor evaporator fan motor electrical requirements—50Hz systems
Hp	Volts	200	230	380-415
2.0	FLA	7.0	6.1	3.5
3.0	FLA	10.1	8.8	5.1
5.0	FLA	15.8	13.7	7.9
7.5	FLA	25.1	21.8	12.5
10.0	FLA	30.2	27.6	15.1
15.0	FLA	46.2	42.0	24.2
20.0	FLA	NA	NA	30.0

1.Refer to General Data Section for standard fan motor size on units.

2.FLA = Full Load Amps

13