Philips 44PL9522, 44PL9773, 55PL9773 setup guide Programming the Remote Control, Vcr Dvd

Page 22

Programming the Remote Control

Your TV remote control can operate accesso- ry devices such as cable boxes, VCRs, DVD players, satellite receivers, and amplifiers.

Normally, the remote is in TV mode. You must press the Select button to switch the remote to one of the accessory modes—CBL, VCR, DVD, SAT, or AMP.

AMP

It is likely you will need to program you remote, but, before you do, try this test:

•Press the Select button repeatedly until the mode you desire lights up. When the light begins blinking, point the remote toward the accessory device, then press the Standby–On button. If the device responds you do not need to program the remote. If not, follow the steps below to program the remote.

1 Look up the number for the device on the list below:

GUIDE

POWER

SELECT

POWER

INFO

HIGH DEFINITION

SAT

DVD619 DVD/CD PLAYER

OPEN/CLOSE

STANDBY-ON

DVD

STOP PLAY PAUSE

PREVNEXT

1Cable (CBL)

2VCR

3DVD

4Satellite (SAT)

5Amplifier (AMP).

Look up the number for the manufac- turer on pages 24–25.

2 Press the Select and Standby–On but- tons at the same time, then release.

3 Press the number for the device fol- lowed by the manufacturers code. The green Standby-On light will blink, indicating the code is valid. If the light does not blink, start again at step 1 using another code (if available).

VCR

CBL

2

2

3

22

Image 22

Contents 55PL9773 44PL9773 44PL9522 Warranty Owner Verification Confirmation Dear Philips product ownerImportant Safety Instructions Contents Features Compact design with low weightWays TV Signals Can Come toYour Home Your High-definition-ready SetDescriptions of Jacks, Cables, and Connectors Cables used RF coaxial cable 75ΩUse only one of the video signal inputs at a time Panel Jack Compatibility InformationPre-connection Recommendations Positioning the TVConnecting a VCR Back of TVConnecting a VCR and Cable Box Connecting an S-Video Device Back of TVConnecting a Standard DVD Player Helpful HintsConnecting a Progressive-scan DVD Player Connecting an HD Satellite Receiver to YPbPr Connecting an HD Satellite Receiver to DVI Back of TVConnecting Surround Sound Equipment Powered Subwoofer Front SpeakersConnecting to the Side InputsVideo Game System Labeling the Audio/Video Input Sources Remote Control Buttons Select CBL VCR DVD SAT AMP and BacklightStandby-On Programming the Remote Control VCR DVDCheck IT OUT Programming the Remote Control Setup Codes AmplifierVCR Operating Accessory Devices with the TV Remote DVD Mode CBL Cable Mode VCR ModeSAT Mode AMP Mode Using Active Control Plus Active Control Plus SettingsAdjusting/Setting the Picture Controls Color temperature, or TintSelecting a Digital Processing Option DemoSelecting a Dynamic Contrast Option Press the Cursor Right button to select PictureSelecting a DNR Dynamic Noise Reduction Option DNR is not available for use with input sources AV3-AV6Turning on Color Enhancement Selecting an AutoPicture Option AutoPicture OptionsSelecting a Picture Format Option Your TV’s Picture Format OptionsAuto Adjusting the TV and Headphone Volume To control the television volumeSelecting a TV Equalizer Option Adjusting TV Speaker Balance Loudness On Off Headphone volume Turning Loudness on or offSettings Demo Install Using Alternate Audio SAP Setting the TV for Stereo Programming Turning the AVL Audio Volume Leveler on or off Adjusting the Delta Volume Selecting an AutoSound Option AutoSound OptionsUsing Closed Captioning CC-1, CC-2, CC-3, or CC-4-DialogueSetting the Sleeptimer Setting the On Timer Using the Channel List Removing Channels from the Channel List Using Lock Channel Using Lock After Blocking Programming Based on TV Ratings TV Ratings from TV BroadcastersBlocking Programming Based on Movie Ratings Movie RatingsTurning the Antenna Attenuator on or off Using Surf Channels SurfUsing Dual Screen and PIP When using Dual Screen Selecting a Picture Freeze Option Photo finishResetting the Audio/Video Settings to Factory Default Values Minimum mode default mode Selecting an On-screen Display OptionSetting up or Changing a PIN Personal Identification Number Setting the Subwoofer Control Setting the Clock-Auto Clock Mode 10 6 8 Auto clock channel Atlantic Using Installation Features Language and Autoprogram For LanguageCleaning the Cabinet Cleaning the ScreenCleaning or Replacing the Filters Replacing the Lamp Groove Resetting the Lamp’s Lifetime Counter You have changed the lampTroubleshooting Picture shakes or is not clear Remote-related Checks Remote control does not workTV-related Checks Picture appears doubled or tripled Picture has no colors or colors are not correctProduct Specifications PictureIndex Factory Service Locations Milwaukee call ChicagoHouston LOS Angeles Limited Warranty Philips Television