Philips PT-FW100NTU Ceiling mount bracket safeguards, Care and Replacement Replacement procedure

Page 42

Care and Replacement

Replacement procedure

Removing and replacing the lamp unit

1.Use a Phillips-head screwdriver to loosen the 2 Lamp unit cover fixing screws on the back of the projector until the screws turn freely, and remove the Lamp unit cover.

Lamp unit cover

Lamp unit cover fixing screws

2.Use a Phillips-head screwdriver to loosen the 2 Lamp unit fixing screws.

3.Hold the handles of the Lamp unit and release the lamp unit lock.

4.Pull the used Lamp unit gently from the projector.

Lamp unit

fixing screws

Handles

5.Replace the new Lamp unit in correct direction.

LAMP RUNTIME will be reset to “0” automatically.

6.Press in the Lamp unit until it clicks and make sure the unit is installed securely.

7.Tighten the 2 Lamp unit fixing screws securely with a Phillips-head screwdriver.

Lamp unit fixing screws

Press here

8.Attach the Lamp unit cover and tighten the 2 Lamp unit cover fixing screws securely with a Phillips-head screwdriver.

Maintenance

Ceiling mount bracket safeguards

The projector and the ceiling mount bracket are designed sufficiently safety though, make sure the safety cable provided with the projector is installed and attached to the bottom of the projector when mounting in the ceiling for safety and security.

NOTE:

•Even if it is guarantee period, the manufacturer is not responsible for any hazard or damage caused by using a ceiling mount bracket which is not purchased from an authorized distributors, or environmental conditions.

•Make sure to use a torque driver and do not use an electrical screwdriver or an impact screwdriver.

•Installation work of the ceiling mount bracket should only be carried by a qualified technician.

•Remove an unused ceiling mount bracket promptly.

Installing the safety cable

1.Install the ceiling mount bracket according to the installation instructions.

2.Loop the security cable around the ceiling mount bracket with less slack.

Lace the cable of the end with a latch through the loop on the other end of the cable.

3.Attach the latch on to the bottom of the projector with a provided screw. Torque: 1.25±0.2 N·m

* Indicated above is ET-PKX100S.

ENGLISH - 42

Page 41 Page 43
Image 42
Page 41 Page 43
Contents Model No. PT-FW100NTU Important Safety Notice Important InformationPT-FW100NTU Trade Name Important Safety NoticeDeclaration of Conformity PanasonicContents Contents SettingsMaintenance AppendixPrecautions with regard to safety Do not look into the lens while the projector is being used Precautions with regard to safetyDo not set up the projector outdoors Use only the specified batteriesDo not mix old and new batteries Remove the used batteries from the remote control promptlyDo not put your weight on this projector Electric shocks can result if this is not doneAccessories Minimum required setting screen Read this firstPreparation Remote control About Your ProjectorTop and front view Projector bodyAbout Your Projector Control panelAbout Your Projector Back and bottom view Computer. Selectable for inputOutput by menu operation Screen size and throw distance Setting upCalculation methods for screen dimensions Getting StartedProjection method Front leg adjusters and throwing angleSetting up Mounting in the ceiling and projecting from frontHorizontal shift Adjusting the Lens shift leverLens shift and positioning Vertical shiftSetting up Projector location range When the screen position is fixedWhen the projector position is fixed Before connection to the projector Connecting with computersConnections LAN terminalConnecting with Component Connecting with AV equipmentConnecting with Video IN/S-VIDEO ConnectionsSwitching the projector on/off Power cordPower indicator Switching the projector on/off Switching on the projectorSwitching off the projector Switch the Main Power on Press the Power buttonPositioning the image Selecting the input signalProjecting an image Focus lever Zoom leverOperating range Remote control operationSetting up the image position automatically OperationSwitching the input signal Using the laser pointerCapturing an image Resetting to the factory default settingsProjecting an image in INDEX-WINDOW mode Stopping the projection temporaryControlling the volume of the speaker Projecting 2 images at a timeEnlarging the centred area Navigating through the Menu Adjusting with the bar scale itemsMenu Navigation Displaying the Main menuMain menu and Sub-menu Menu NavigationWEB Control Live Mode CUT Status Initialize Password Change Network StandbyContents 169 1610Picture menu Detailed Setup For S-VIDEO/VIDEO signalsFor RGB signals Position menu Screen Format menu Aspect ratio depend on signalsFrame Lock OptionOption menu Signal Search Power OFF TimerAuto Setup Direct Power onHighland Closed CaptionTest Pattern Security menu Input PasswordPassword Change Text DisplayNetwork menu Items in Network menuNetwork menu, the following items are available Lamp indicator TEMP, Lamp and Filter IndicatorsManaging the indicated problems Temp indicatorCare and Replacement Cleaning the projectorReplacing the ARF Auto Rolling Filter Replacing the Lamp unit Care and Replacement Resetting the FilterWhen to replace the Lamp unit Before replacing the Lamp unitInstalling the safety cable Ceiling mount bracket safeguardsCare and Replacement Replacement procedure Removing and replacing the lamp unitTroubleshooting Quality *2 List of compatible signalsTechnical Information Dots *1 KHz MHzSerial terminal Computer connection guidance Technical Information Cable specificationsControl commands ProjectorInput signal Lamp switchingSwitching input Signals Remote terminalSpecifications Audio COMPONENT1OUT Computer AudioScreen size and throw distance for 169 aspect ratio Screen size and throw distance for 43 aspect ratioUnit mm DimensionsTrademark acknowledgements These Operating Instructions are printed on recycled paperCalculation methods IndexALS Ambient Luminance Sensor ARF Auto Rolling Filter LeverNavigation buttons IndexMains lead Screen sizeAvis important concernant la sécurité Imformation ImportanteNuméro de série Avertissement Avis important concernant la sécuritéInformation Importante AdvertenciaPrécautions de sécurité AvertissementMises EN Garde Précautions de sécuritéUtiliser uniquement les piles spécifiées Ne pas mélanger des piles usées et des piles neuvesSinon cela peut causer des chocs électriques Précautions lors de linstallation Précautions lors du transportPrécautions lors de lutilisation Remplacement de lunité de la lampe Délai de remplacement de lUnité de la lampeAvant de remplacer le lUnité de la lampe Retirer et remplacer la lampe Installation du câble de sécuritéProtections du support de montage au plafond De lUnité dePanasonic Projector Systems Company Technical Support
Top Page Image Contents