Philips PT-FW100NTU manual Read this first, Minimum required setting screen, Preparation

Page 10

Read this first

Minimum required setting screen

When you start the projection for the first time, the minimum required setting screen for projection will be displayed.

LANGUAGE

Select the required language setting.

Preparation

LANGUAGE

 

 

PLEASE SELECT LANGUAGE

 

SELECT

 

ENTER

Press F G I H buttons of the Remote control or Control panel on the projector to highlight the required language, and press ENTER to proceed to the next setting.

INSTALLATION

Press I H buttons of the Remote control or Control panel on the projector to select the required installation method. Press G to proceed to the HIGHLAND setting.

FRONT/DESK

Setting on a desk/floor and

projecting from front

 

FRONT/CEILING

Mounting in the ceiling and

projecting from front

 

REAR/DESK

Setting on a desk/floor and

projecting from rear

 

REAR/CEILING

Mounting in the ceiling and

projecting from rear

 

SCREEN FORMAT

Select the required screen format by pressing I H.

16:10

When project on a 16:10 or 4:3

 

screen.

16:9

When project on a 16:9 screen.

OPTION

Select the current projection method, screen size and fan speed setting. If you need return to the previous setting, press the RETURTN button.

OPTION

INSTALLATION

FRONT/DESK

SCREEN FORMAT

16:10

HIGHLAND

OFF

 

RETURN

SELECT

 

 

ENTER

HIGHLAND

If you use the projector at high elevation, the HIGHLAND setting need to be ON to set the fan speed high. Press I H to select the required option. If you need to return to the INSTALLATION, press F.

OFF

The fan speed is low.

ON

The fan speed is high.

NOTE:

•At 1 400 m (4 593 ft) above sea level, the setting must be ON.

•The loudness of fan noise depends on the HIGHLAND setting.

Press the ENTER button to start the projection.

Once you finish the minimum requirement setting, it will not be displayed again unless the projector is initialized. See “INITIALIZE ALL” on page 36.

You can change the settings from the MAIN MENU. See “Menu Navigation” on page 27.

ENGLISH - 10

Page 9 Page 11
Image 10
Page 9 Page 11
Contents Model No. PT-FW100NTU Important Information Important Safety NoticePT-FW100NTU Trade Name Important Safety NoticeDeclaration of Conformity PanasonicContents Contents SettingsMaintenance AppendixPrecautions with regard to safety Do not look into the lens while the projector is being used Precautions with regard to safetyDo not set up the projector outdoors Use only the specified batteriesDo not mix old and new batteries Remove the used batteries from the remote control promptlyDo not put your weight on this projector Electric shocks can result if this is not doneAccessories Read this first Minimum required setting screenPreparation Remote control About Your ProjectorTop and front view Projector bodyAbout Your Projector Control panelComputer. Selectable for input About Your Projector Back and bottom viewOutput by menu operation Screen size and throw distance Setting upCalculation methods for screen dimensions Getting StartedProjection method Front leg adjusters and throwing angleSetting up Mounting in the ceiling and projecting from frontHorizontal shift Adjusting the Lens shift leverLens shift and positioning Vertical shiftWhen the screen position is fixed Setting up Projector location rangeWhen the projector position is fixed Before connection to the projector Connecting with computersConnections LAN terminalConnecting with Component Connecting with AV equipmentConnecting with Video IN/S-VIDEO ConnectionsPower cord Switching the projector on/offPower indicator Switching the projector on/off Switching on the projectorSwitching off the projector Switch the Main Power on Press the Power buttonPositioning the image Selecting the input signalProjecting an image Focus lever Zoom leverOperating range Remote control operationSetting up the image position automatically OperationSwitching the input signal Using the laser pointerCapturing an image Resetting to the factory default settingsProjecting an image in INDEX-WINDOW mode Stopping the projection temporaryProjecting 2 images at a time Controlling the volume of the speakerEnlarging the centred area Navigating through the Menu Adjusting with the bar scale itemsMenu Navigation Displaying the Main menuMain menu and Sub-menu Menu NavigationWEB Control Live Mode CUT Status Initialize Password Change Network StandbyContents 169 1610Picture menu For S-VIDEO/VIDEO signals Detailed SetupFor RGB signals Position menu Screen Format menu Aspect ratio depend on signalsFrame Lock OptionOption menu Signal Search Power OFF TimerAuto Setup Direct Power onClosed Caption HighlandTest Pattern Security menu Input PasswordPassword Change Text DisplayItems in Network menu Network menuNetwork menu, the following items are available Lamp indicator TEMP, Lamp and Filter IndicatorsManaging the indicated problems Temp indicatorCleaning the projector Care and ReplacementReplacing the ARF Auto Rolling Filter Replacing the Lamp unit Care and Replacement Resetting the FilterWhen to replace the Lamp unit Before replacing the Lamp unitInstalling the safety cable Ceiling mount bracket safeguardsCare and Replacement Replacement procedure Removing and replacing the lamp unitTroubleshooting Quality *2 List of compatible signalsTechnical Information Dots *1 KHz MHzSerial terminal Computer connection guidance Technical Information Cable specificationsControl commands ProjectorInput signal Lamp switchingSwitching input Signals Remote terminalSpecifications Audio COMPONENT1OUT Computer AudioScreen size and throw distance for 169 aspect ratio Screen size and throw distance for 43 aspect ratioUnit mm DimensionsTrademark acknowledgements These Operating Instructions are printed on recycled paperCalculation methods IndexALS Ambient Luminance Sensor ARF Auto Rolling Filter LeverNavigation buttons IndexMains lead Screen sizeImformation Importante Avis important concernant la sécuritéNuméro de série Avertissement Avis important concernant la sécuritéInformation Importante AdvertenciaPrécautions de sécurité AvertissementMises EN Garde Précautions de sécuritéNe pas mélanger des piles usées et des piles neuves Utiliser uniquement les piles spécifiéesSinon cela peut causer des chocs électriques Précautions lors du transport Précautions lors de linstallationPrécautions lors de lutilisation Délai de remplacement de lUnité de la lampe Remplacement de lunité de la lampeAvant de remplacer le lUnité de la lampe Retirer et remplacer la lampe Installation du câble de sécuritéProtections du support de montage au plafond De lUnité dePanasonic Projector Systems Company Technical Support
Top Page Image Contents