Xerox 92C IPS manual Enabling or disabling the modem, Modem Enable/Disable window

Page 48

SETTING UP THE PRINTER CONTROLLER

Enabling or disabling the modem

Your service representative may install a modem in your system for diagnostic purposes. This modem is used for dial-in servicing and diagnostics when needed by your service representative.

To enable or disable the modem, follow these steps:

1.Select Modem Enable/Disable from the Configuration pull-down menu. The Modem Enable/Disable window displays.

Figure 3-5.Modem Enable/Disable window

2.Click Enabled or Disabled, as appropriate.

3.To allow Shell access to a service representative, mark the “Remote Shell Access” checkbox.

4.Click Apply. The Modem Enable window displays, prompting you for a password.

5.Enter the root password.

Note: The modem will automatically be disabled after rebooting the system.

3-6	XEROX DOCUPRINT 92C IPS GUIDE TO CONFIGURING AND MANAGING THE SYSTEM

Image 48

Contents Version 7.1 August 2000 721P89180 Page Laser safety Ozone informationOperation safety Table of contents Setting up the Printer Controller Setting the system configurationIndex INDEX-1Viii Contents About this guideConventions Related publications DocuPrint IPS Interactive Customer Documentation CDXii Introduction to the graphical user interface Graphical user interface screenIntroduction to the Graphical User Interface Using the user interface screens Pull-down menusClick method Drag methodButtons Example of a selection button from the IPS main windowMoving a window or icon Reducing a windowEntering in text Exiting a window If the pin is outIf the pin is IPS main window 10.IPS main windowConfiguration menu MenusIntroduction to the Graphical User Interface Diagnostics menu 12.Diagnostics pull-down menuAdministration menu Backup Configuration Files Enables backing upSystem Options menu 14.System Options pull-down menuInput Configuration section 15.Input Configuration section of Ipds main windowOutput Configuration section 16.Output Configuration section of IPS main windowIntroduction to the Graphical User Interface Setup and status information 18.Control Unit Configuration section of main window19.Status section of main window Host Job Control section 20.Host Job Control section of main windowSubwindow buttons 21.Window with Quit and Apply buttons Powering on the IPS system Starting and stopping the systemSee HCU Messages in the Xerox DocuPrint IPS Messages Powering off the IPS system Routine operation System Shutdown Confirmation windowAfter a power outage Communicating with the host computerPlacing the IPS online Taking the IPS offlineStarting a print job Stopping the printerPrinter status Automatic print job recovery Rebooting the Printer ControllerExiting power saver mode Resuming printingRemoving media from the processor Setting up the Printer Controller Selecting a language Language windowSpecifying the system interface Selecting channel interface Channel Options windowSelecting TCP/IP interface TCP/IP interface windowModem Enable/Disable window Enabling or disabling the modemAllocating memory for resources System Resource Limits windowDisplaying and adding resident fonts Displaying resident fontsAdding resident fonts Var/db/fonts/inputInput Media pull-down menu 10.Administration pull-down menu Loading the IPS software license text string11.IPS Authorization window Switching modes Dual Mode Page Setting the system configuration Control Unit Configuration section of main window Privilege ModesChanging the Privilege Mode Changing the password for a Privilege Mode Accessing configuration tasks Configuration menu tasksIndicating the input resolution Resolution windowSpecifying the maximum simplex value Maximum Simplex windowSpecifying the extraction color for highlight color printing Extraction Color for Highlight Printing window All non-red except BlackAny non-red AnyExtraction Color window with color pull-down menu Procedure for printing the palettes Printing the IPS color samplesExtraction color palettes Shades and tints palettesRotating the page origin Var/db/palettenameSetting the System Configuration Continuous Form Selection window Specifying the media units Media Units windowSetting optional processing parameters Optional Processing Parameters window Diagnostics menu tasks Printing samplesSetting the System Configuration 11.Portion of Testdocs list of samples to print Setting the System Configuration 12.PQA status window example Capturing and executing a trace Capturing a trace15.Trace Mode Options window Tracetest Executing a captured tracePrinting a trace file Conprt -d -x 3520x2480 tracedebug /var/dbSetting of the debug level Updating the software using a CD or a diskette Updating the software remotely System Options menu tasks 16.System Options pull-down menuSpecifying the input configuration Example of an input configuration Selecting simplex or duplex printing 19.Single simplex media iconSetting up margin values 21.default pull-down menuSetting up the Media Library 23.Modify Margin Settings window24.IPS Input Configuration window Creating a media icon25.Media Library window 26.Media Type window 27.Add a New Form Type window Setting the System Configuration Editing the media defaults Changing a media iconDeleting a media icon 28.Media Defaults window Adding a new input configuration 29.Input Configuration pull-down menu30.Input Configuration window 31.Tray cells section of a sample input configuration Setting the System Configuration 32.Tray cells section of a sample input configuration 33.File Name Entry window Changing an input configuration file 34.Input Configuration pull-down menuDeleting an input configuration file 35.Input Configuration pull-down menuCorrecting a feeder tray mismatch error 37.Feeder tray mismatch error messageSpecifying the output configuration Example of an output configuration Creating a new output configuration 39.Output Configuration pull-down menu41.Default Ipds Bin pull-down menu 42.DFA Profile pull-down menu 43.Bins section of the Output Configuration window For systems with DFA 45.Finishing Attributes window systems with DFASetting the System Configuration For systems with a stitcher 46.Stitching Attributes windowChanging an output configuration Deleting an output configuration Adding a DFA profile49.DFA Profile Name pull-down menu You may make changes to the following fields 51.File Name Entry window Changing a DFA profile Deleting a DFA profileBacking up and restoring configuration files Saving configuration files to diskette 52.Backup Configuration Files windowRestoring configuration files from diskette Index NumericsIndex Index Index Index Page

Related manuals

Manual 49 pages 45.72 Kb