Belkin F1DA104Z, F1DA108Z Pre-Configuration, Where to Place the PRO3 KVM Switch, For USB Servers

Page 12

Installation

Pre-Configuration

Where to Place the PRO3 KVM Switch

The enclosure of the PRO3 KVM Switch is designed for stand-alone or rack-mount configuration. The 8- and 16-Port PRO3 KVM Switches are natively rack-mountable in standard, 19-inch server racks. Rack-mount hardware is included with these Switches for a sturdy rack installation. An optional OmniView Rack-Mount Kit (F1D005) is available for use with the 4-Port PRO3 KVM Switch.

Consider the following when deciding where to place the PRO3 KVM Switch:

•whether or not you intend to use the direct-access port selectors

•the lengths of the cables attached to your keyboard, monitor, and mouse

•the location of your servers in relation to your console

•the lengths of the cables you use to connect your servers to the PRO3 KVM Switch

Cable-Distance Requirements:

For PS/2 Servers:

VGA signals transmit best up to 25 feet (7.6m). Beyond that length, the probability of video degradation increases. For this reason, Belkin recommends that the length of the cables between the PRO3 KVM Switch and the connected servers does not exceed 25 feet (7.6m).

For USB Servers:

USB signals can be transmitted up to 15 feet (4.5m) between the PRO3 KVM Switch and server. Beyond that length, the probability of USB-signal failure is likely, and may cause the device to fail.

Note: The Belkin OmniView CAT5 Extender (F1D084) may be used to extend your console (keyboard, mouse, and monitor) by up to 300 feet (91m).

Cautions and Warnings!

Avoid placing cables near fluorescent lights, air-conditioning equipment, or machines that create electrical noise (e.g., vacuum cleaners).

Before attempting to connect anything to the PRO3 KVM Switch or your servers, ensure that everything is powered off. Plugging and unplugging cables while servers are powered on may cause irreversible damage of the servers and/or the PRO3 KVM Switches. Belkin is not responsible for damage caused in this way.

You are now ready to begin installation of your PRO3 KVM Switch. The following sections (pages 11-19) provide complete instructions for the hardware setup of a single PRO3 KVM Switch (F1DA104Z, F1DA108Z, F1DA116Z).

10

Page 11 Page 13
Image 12
Page 11 Page 13
Contents OmniView PRO3 KVM Switch Table of Contents Package Contents Feature Overview Hot KeysFlash Upgrade Equipment Requirements CablesSection System Requirements OS PlatformsKeyboards MiceUnit Display Diagrams Front View of the PRO3 KVM SwitchBack View of the PRO3 KVM Switch Specifications Pre-Configuration Where to Place the PRO3 KVM SwitchCable-Distance Requirements For PS/2 Servers For USB ServersMounting the PRO3 KVM Switch Bracket Installation F1DA108Z and F1DA116ZOptional Bracket Installation F1DA104Z StepSection Connecting the Console to the PRO3 KVM Switch Section Connecting Servers to the PRO3 KVM Switch PS/2 Connection Power up your server Connecting Servers to the PRO3 KVM Switch USB Connection Section Connecting Multiple PRO3 KVM Switches Daisy-Chaining BANK-DIP-Switch Configuration Chart How to Assign a Bank AddressExample of Daisy-Chain Configuration Getting StartedConnecting the Primary and Secondary KVM Switches Step Connecting the Servers Step Powering Up the Systems Selecting a Server or Bank Using Hot-Key Commands Section Selecting a Server Using Direct-Access Port Selectors Selecting a Bank Using Scroll ButtonsAutoScan Mode OSD Keyboard Commands On-Screen Display OSDMain OSD Main Menu Main-Menu-Page Keyboard Commands User SettingUsername admin Password belkin LanguageAccess List Hot KeyAutoScan Time Keyboard Hot-Key-Command Shortcuts Command FunctionSun Combo and Mac Key Mapping Windows Sun Micro Mac USB KeyboardTo update the firmware, you will need the following items Updating FirmwareHow far can the server be from the PRO3 KVM Switch? Can I mix PS/2 and USB devices on the KVM console?Can I mix PS/2 and USB servers on the host side? Does the PRO3 KVM Switch require an AC adapter? Can I use the PRO3 KVM Switch to switch video signals only?Does the PRO3 KVM Switch support Linux? How long is the warranty for the PRO3 KVM Switch?Am getting a black screen on my monitor Mouse is not detected at boot up Server boots up, but the mouse does not workTroubleshooting USBGlossary FCC Statement How to get service How state law relates to the warrantySection Belkin Tech Support Belkin B.V
Top Page Image Contents