Belkin F1DP108G user manual SMB Server Interface Module, PS/2

Page 12

Overview

Dimensions:

(F1DP108G) 17.25 x 1.75 x 7.5 in.

 

(438 x 45 x 190mm)

 

(F1DP116G) 17.25 x 1.75 x 7.5 in.

 

(438 x 45 x 190mm)

Weight:

(F1DP108G) 5.0 lbs. (2.3kg.)

 

(F1DP116G) 5.0 lbs. (2.3kg.)

*May be daisy-chained with up to 15 OmniView SMB and PRO2 KVM Switches. OmniView SMB KVM-over-IP Switches may not be daisy-chained together.

**Typical bandwidth is defined as typical “non-intensive” administrative use at 16-bit color, 1024x768 resolution.

Note: Specifications are subject to change without notice.

SMB Server Interface Module, PS/2

Part No.:

F1DP101A-AP

Emulation:

Keyboard and mouse signals

Power:

Via attached server

Keyboard/Mouse Connection:

MiniDIN6 (PS/2)

Monitor Connection:

HDDB15 male (VGA)

Resolution Support:

Up to 1600x1200 @ 75Hz

Max. Distance Supported:

100 ft. (30m)

Weight:

0.25 lbs. (0.11kg.)

Unit Dimensions:

1.8 x 3.5 x 0.9 in. (46 x 89 x 23mm)

VGA-Cable Length:

8 in. (203mm)

PS/2-Cable Length:

19 in. (483mm)

1

2

3

4

5

6

7

8

9

10

section

9

Image 12
Contents OmniView SMB KVM-over-IP Switch Table of Contents Using the Switch from a Remote Console Using the Switch from a Local ConsolePackage Contents IntroductionRemote-Management Features OverviewOther Features Equipment Requirements Server Interface ModulesOmniView SMB Server Interface ModulesCables Belkin UTP Patch Cables System Requirements Unit Display Diagrams Front ViewBack View Specifications SMB Server Interface Module, PS/2 SMB Server Interface Module, USB SMB Server Interface Module, Legacy SunVGA-Cable Length USB-Cable Length VGA-Cable Length MiniDIN8-Cable LengthLocal Installation Pre-ConfigurationWhere to place the Switch Local Installation Cable-Distance Requirements for PS/2, USB, and Sun ServersMounting the Switch MAC Address Device NumberConnecting the Console to the Switch Local Installation Connecting Servers to the Switch PS/2 Connection Local Installation Connecting Servers to the Switch USB Connection Local Installation Connecting Servers to the Switch Sun MiniDIN8 Connection Local Installation Powering Up the Systems Daisy-Chaining Multiple KVM Switches Optional How to Assign a Bank AddressBANK-DIP-Switch-Configuration Chart SMB CAT5 KVM Switches DIP SWITCH# SMB CAT5 Bank AddressExample of Daisy-Chain Configuration Connecting the Primary and Secondary KVM Switches Getting StartedConnecting the servers Remote Installation Identifying the IP AddressLogin Logging into the Web InterfaceRemote Installation Network Configuration Device NameRequired TCP Ports Enable Dhcp Snmp SettingsSet a Static IP User Settings AdministratorUser View Only To add a new userTo edit a user To delete a userBlocking a standard user and View Only user To block a userSwitch Configuration Switch-ConfigurationInstalling new Switch-Definition Files SDFs To install the SDFTo specify and name servers Serial Settings To configure your serial deviceSecurity Settings Password PolicyAccount Blocking Idle Timeout To install an SSL certificateSSL Certificate Maintenance Firmware Upgrade To upgrade firmwareRestore Factory Settings To restore factory settingsLogging Out Using the Switch from a Remote Console Starting a Remote SessionTo start a remote session Full-Screen Mode To work in full-screen modeUsing the Drop-Down Bar Disconnecting the Remote SessionHiding/Unhiding the Drop-Down Bar Mouse Configuration and Settings Mouse-Pointer AlignmentTo align mouse pointers Mouse-Pointer CalibrationManual Settings You must manually synchronize the mouse pointers ifTo manually synchronize mouse pointers USB Option Mouse-Pointer Options Windows XPTo change the mouse-emulation settings Advanced-Mouse EmulationKeyboard Configuration and Settings To transmit a keyboard sequenceTo add a keyboard sequence To record a keyboard sequence Add-Special-Key BoxVideo Configuration and Settings Manual Video AdjustTo refresh the video settings To adjust the video manuallyAuto Video Adjust To adjust the video automaticallyPerformance Settings Bandwidth To change the bandwidth settingsSelecting a Server To connect to a different serverAdditional Features Session ProfileRestoring Factory Defaults To restore factory defaultsUsing the Switch from a Local Console Selecting a Server or Bank Using Hot KeysSelecting a Server or Bank G e W n Selecting a Server Using Port Selectors Selecting a Bank Using Scroll ButtonsAutoScan Mode On-Screen Display OSD Main OSD-MenuOSD-Menu Keyboard Commands Function/HelpFunction/Help-Page Keyboard Commands Admin PasswordScan Scan TimeTimeout Monitor-DDC2 FeatureHot Key Hot-Key-Command Shortcuts Sun Combo Keys Sun Key Combo KeyUpdating Firmware Frequently Asked Questions Can I use the Switch on my Sun server that supports USB?Frequently Asked Questions Problem SolutionLocal Console GeneralKeyboard MouseUSB Remote Console Video quality is bad and/or grainy Glossary Section Belkin International, Inc., Limited 2-Year Product Warranty InformationFCC Statement How to get service Information Belkin Tech Support Belkin B.V
Related manuals
Manual 84 pages 50.94 Kb