Belkin F1DP108G user manual How to get service

Page 82

Information

purchaser, or if Belkin determines that the Belkin product has been improperly installed, altered in any way, or tampered with. The Belkin Product Warranty does not protect against acts of God such as flood, lightning, earthquake, war, vandalism, theft, normal-use wear and tear, erosion, depletion, obsolescence, abuse, damage due to low voltage disturbances (i.e. brownouts or sags), non- authorized program, or system equipment modification or alteration.

How to get service.

To get service for your Belkin product you must take the following steps:

1.Contact Belkin International, Inc., at 501 W. Walnut St., Compton, CA 90220, Attn: Customer Service, or call (800)-223-5546, within 15 days of the Occurrence. Be prepared to provide the following information:

a.The part number of the Belkin product.

b.Where you purchased the product.

c.When you purchased the product.

d.Copy of original receipt.

2.Your Belkin Customer Service Representative will then instruct you on how to forward your receipt and Belkin product and how to proceed with your claim.

Belkin reserves the right to review the damaged Belkin product. All costs of shipping the Belkin product to Belkin for inspection shall be borne solely by the purchaser. If Belkin determines, in its sole discretion, that it is impractical to ship the damaged equipment to Belkin, Belkin may designate, in its sole discretion, an equipment repair facility to inspect and estimate the cost to repair such equipment. The cost, if any, of shipping the equipment to and from such repair facility and of such estimate shall be borne solely by the purchaser. Damaged equipment must remain available for inspection until the claim is finalized. Whenever claims are settled, Belkin reserves the right to be subrogated under any existing insurance policies the purchaser may have.

How state law relates to the warranty.

THIS WARRANTY CONTAINS THE SOLE WARRANTY OF BELKIN. THERE ARE NO OTHER WARRANTIES, EXPRESSED OR, EXCEPT AS REQUIRED BY LAW, IMPLIED, INCLUDING THE IMPLIED WARRANTY OR CONDITION OF QUALITY, MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE, AND SUCH IMPLIED WARRANTIES, IF ANY, ARE LIMITED IN DURATION TO THE TERM OF THIS WARRANTY.

Some states do not allow limitations on how long an implied warranty lasts, so the above limitations may not apply to you.

IN NO EVENT SHALL BELKIN BE LIABLE FOR INCIDENTAL, SPECIAL, DIRECT, INDIRECT, CONSEQUENTIAL OR MULTIPLE DAMAGES SUCH AS, BUT NOT LIMITED TO, LOST BUSINESS OR PROFITS ARISING OUT OF THE SALE OR USE OF ANY BELKIN PRODUCT, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGES.

1

2

3

4

5

6

7

8

9

10

section

79

Image 82
Contents OmniView SMB KVM-over-IP Switch Table of Contents Using the Switch from a Remote Console Using the Switch from a Local ConsolePackage Contents IntroductionRemote-Management Features OverviewOther Features OmniView SMB Server Equipment RequirementsServer Interface Modules Interface ModulesCables Belkin UTP Patch CablesSystem Requirements Front View Unit Display DiagramsBack View Specifications SMB Server Interface Module, PS/2 VGA-Cable Length USB-Cable Length SMB Server Interface Module, USBSMB Server Interface Module, Legacy Sun VGA-Cable Length MiniDIN8-Cable LengthPre-Configuration Local InstallationWhere to place the Switch Local Installation Cable-Distance Requirements for PS/2, USB, and Sun ServersMounting the Switch MAC Address Device NumberConnecting the Console to the Switch Local Installation Connecting Servers to the Switch PS/2 Connection Local Installation Connecting Servers to the Switch USB Connection Local Installation Connecting Servers to the Switch Sun MiniDIN8 Connection Local Installation Powering Up the Systems Daisy-Chaining Multiple KVM Switches Optional How to Assign a Bank AddressBANK-DIP-Switch-Configuration Chart SMB CAT5 KVM Switches DIP SWITCH# SMB CAT5 Bank AddressExample of Daisy-Chain Configuration Connecting the Primary and Secondary KVM Switches Getting StartedConnecting the servers Remote Installation Identifying the IP AddressLogin Logging into the Web InterfaceRemote Installation Device Name Network ConfigurationRequired TCP Ports Snmp Settings Enable DhcpSet a Static IP Administrator User SettingsUser View Only To add a new userBlocking a standard user and View Only user To edit a userTo delete a user To block a userSwitch Configuration Switch-ConfigurationTo install the SDF Installing new Switch-Definition Files SDFsTo specify and name servers Serial Settings To configure your serial devicePassword Policy Security SettingsAccount Blocking To install an SSL certificate Idle TimeoutSSL Certificate Maintenance Firmware Upgrade To upgrade firmwareTo restore factory settings Restore Factory SettingsLogging Out Starting a Remote Session Using the Switch from a Remote ConsoleTo start a remote session Full-Screen Mode To work in full-screen modeDisconnecting the Remote Session Using the Drop-Down BarHiding/Unhiding the Drop-Down Bar To align mouse pointers Mouse Configuration and SettingsMouse-Pointer Alignment Mouse-Pointer CalibrationYou must manually synchronize the mouse pointers if Manual SettingsTo manually synchronize mouse pointers USB Option Mouse-Pointer Options Windows XPTo change the mouse-emulation settings Advanced-Mouse EmulationTo transmit a keyboard sequence Keyboard Configuration and SettingsTo add a keyboard sequence To record a keyboard sequence Add-Special-Key BoxTo refresh the video settings Video Configuration and SettingsManual Video Adjust To adjust the video manuallyAuto Video Adjust To adjust the video automaticallyPerformance Settings Bandwidth To change the bandwidth settingsSelecting a Server To connect to a different serverAdditional Features Session ProfileRestoring Factory Defaults To restore factory defaultsSelecting a Server or Bank Using Hot Keys Using the Switch from a Local ConsoleSelecting a Server or Bank G e W n Selecting a Server Using Port Selectors Selecting a Bank Using Scroll ButtonsAutoScan Mode On-Screen Display OSD Main OSD-MenuOSD-Menu Keyboard Commands Function/HelpScan Function/Help-Page Keyboard CommandsAdmin Password Scan TimeMonitor-DDC2 Feature TimeoutHot Key Hot-Key-Command Shortcuts Sun Combo Keys Sun Key Combo KeyUpdating Firmware Frequently Asked Questions Can I use the Switch on my Sun server that supports USB?Frequently Asked Questions Local Console ProblemSolution GeneralKeyboard MouseUSB Remote Console Video quality is bad and/or grainy Glossary Section Information Belkin International, Inc., Limited 2-Year Product WarrantyFCC Statement How to get service Information Belkin Tech Support Belkin B.V
Related manuals
Manual 84 pages 50.94 Kb