SATO 410e, 400e manual Test Printing, Reloading Media, Powering OFF

Page 64

Unit 4: Operation

PRINTING

At this point, both the printer and the operator should be ready to print labels or tags. One can begin by commencing production or by printing a test label first. To begin production, simply use the operator panel as directed in the Introduction unit of this manual.

TEST PRINTING

A test label is designed to assist in the identification of print problems. Refer to the Troubleshooting unit of this manual for instructions on printing a test label. Once identifying any print issues that may prevail, refer to the Maintenance unit for specific instructions on remedy.

NOTE: If the instructions being sought are not present in the Maintenance unit, those instructions have been deemed too complex for the operator to perform. Contact your service representative for assistance.

RELOADING MEDIA

When replenishing the media supply with the same type and size, it’s not necessary to power the printer off. Once properly loading the media, press the START/STOP key and the printer will automatically feed and correctly position the media for printing.

POWERING OFF

Before powering off the printer, feed the printed labels or tags from the printer by pressing the EJECT key while the printer is online. Any printed media that is remaining in the printer will be ejected and cut. The unprinted media will be retracted to place the first print line under the print head.

NOTE: The eject operation may be controlled via software commands from the host, as well as, locally.

After the printed media has been ejected from the printer, place the printer in the offline state before removing power. If the label/tag position is not disturbed while the power is off, the first printable label/tag will be in the correct position when the power is reapplied. The media type setting is retained in the printer’s memory even though power is removed. When the power is reapplied, the first print line of the label/tag will be correctly positioned under the print head for printing.

SATO XL400-410e Operator Manual

PN 9001135A

Page 4-30

Page 63 Page 65
Image 64
Page 63 Page 65
Contents XL400e / XL410e Printers That may appear Table of Contents Troubleshooting OperationMaintenance Adjustment ProceduresPN 9001135A Introduction About this Manual Result in Presonal InjuryGeneral Description 1a, Primary ComponentsControl Features Buttons & Switches2b, Control Features Page Technical Data Physical Characteristics PowerEnvironmental ProcessingCharacter Font Capabilities Interface Modules BAR Code CapabiltiesRegulatory Approvals Installation Unpacking & Parts Identification Unpacking and Parts IdentificationSite Location Printer InstallationMedia Selection Media Loading 3a, Media Loading3b, Media Loading 3d, Media Loading Ribbon Loading 3f, Media Loading4a, Ribbon Loading 4c, Ribbon Loading 4e, Ribbon Loading 4g, Ribbon Loading Interface Selection RS232C SpecificationsRS232 Serial Interface RS232C Serial Interface Signals PIN Direction Signal DefinitionCable Requirements DB9 Host Connection DB9 PrinterSpecifications IEEE1284 Parallel InterfaceACK Init802.11B Wireless 80211B Wireless SpecificationsUniversal Serial BUS USB Adapter Local Area Network LAN EthernetReceive Buffer ACK/NAK ProtocolAccessories Installation Pcmcia Memory UpgradeLabel Stacker Installation Stacker UnitOperation Printer Configuration DIP Switch PanelsDSW1 Default Settings DSW1 ConfigurationDSW1 Function Descriptions OFFDSW2 Default Settings DSW2 ConfigurationConfiguration DSW2 Function DescriptionsDSW1 DSW3 Default SettingsFunction Description Configuration Modes Normal ModeTest Print Mode Test Print ModeAdvanced Mode Advanced ModeDefault Settings Mode Default Settings ModeFlash Memory Download Mode Download Font Deletion Status Description Acsii HEX TransferFlash Memory Download Mode User Download Mode User Download ModeHEX Dump Mode Hex Dump ModeCard Mode FeedNON-STANDARD Clear Mode Non-Standard Clear ModeService Mode 10a, Service Mode Test Print10b, Service Mode Sensor Level 10c, Service Mode Pitch Offset 10d, Service Mode Cut Offset 10e, Service Mode Backfeed Offset 10f, Service Mode Counter Display Normal Mode Default Settings ModeMenu Description NON-STANDARD Code ClearAdvanced Mode Flash Memory & User Download ModesCard Mode User Test Print ModeService Mode Operational Adjustments Potentiometer DESCRIPTION/PROCEDURE11, Adjustment Panel Cutter Sensor Positioning 14a, Cutter Sensor PositioningOperator Panel 15a, Tilting Operator PanelPowering OFF PrintingTest Printing Reloading MediaTroubleshooting Error Signals LED LCD Message Beep RemedyPrinter Troubleshooting No Printed Image Meandering MediaPrinter Creates a Blank Label Incorrect Label PositioningInterface Troubleshooting CHK Troubleshooting StepLAN Ehternet Interface Performance Testing Multimeter with Test ModuleTest Chart Module Dial Connector PIN Function Multimeter AloneTest Print Troubleshooting Hex Dump ModeTest Label Printing Sample Test Label Sensor Locations Sensor LocationsMaintenance Cleaning Procedures DamageReplacement Procedures Fuse ReplacementPrint Head Replacement Print Head to Prevent Damage to ITS ElementsRibbon Roller Replacement Ribbon Roller ReplacementAdjustment Procedures Print Defects Relative ProcedurePrint Head Balance Adjustment Print Head Balance AdjustmentPrint Head Alignment Print Head AlignmentPressure Roller Alignment Pressure Roller AlignmentPressure Roller Balance Pressure Roller BalanceRibbon Guide Adjustment Ribbon Guide AdjustmentRibbon Spindle Tensioning 10, Ribbon Spindle TensioningPitch Sensor Adjustment Label GAP & Center Hole Media Multimeter AlonePitch Sensor Adjustment EYE-MARK Media 11, Test Module & Sensor Potentiometers Pitch Sensor Adjustment R-CORNER Media Pitch Sensor Adjustment Side Hole Media Jump Hole Sensor Adjustment Ribbon Sensor Adjustment VR3Cutter Sensor Adjustment VR1SG / HO VR2

400e, 410e specifications

The SATO 410e and 400e are advanced thermal transfer printers designed for high-performance label printing in a variety of industries, including retail, logistics, and manufacturing. These models are renowned for their reliability, efficiency, and quality output, making them essential tools for businesses that demand precision and durability in their labeling processes.

One of the standout features of the SATO 410e and 400e is their exceptional print quality. They offer a resolution of up to 600 dpi, ensuring that even the most intricate details in barcodes, logos, and text are printed with clarity. This high resolution is crucial for applications that require precision, such as product labeling and inventory management.

The SATO 410e is equipped with an intuitive user interface that simplifies operation. Its LCD display provides real-time information about print status, and its control panel is designed for ease of navigation, reducing the learning curve for new users. On the other hand, the SATO 400e emphasizes compact design without compromising performance, making it an ideal choice for businesses with limited space or needing a mobile labeling solution.

Both models feature a robust set of connectivity options, including USB, Ethernet, and serial interfaces, allowing for seamless integration into existing IT infrastructures. This versatility makes them suitable for various deployment scenarios, whether used standalone or in networked environments.

In terms of speed, the SATO 410e and 400e are engineered to deliver rapid printing capabilities. The 410e can produce labels at a speed of up to 300 mm per second, while the 400e also showcases impressive speed without sacrificing quality. This capability is vital for high-volume printing tasks common in warehousing and distribution operations.

The technology behind these printers includes SATO’s innovative ARCP (Automatic Ribbon Control Path), which optimizes ribbon usage and minimizes waste, contributing to cost-effective printing solutions. Additionally, the SATO 410e and 400e support a wide range of media types and sizes, accommodating various labeling needs from small tags to large shipping labels.

Both models are also designed with durability in mind. They are built to withstand the rigors of industrial environments, ensuring longevity and consistent performance. With features like a strong casing and reliable internal components, users can expect these printers to maintain operational integrity even under demanding conditions.

In conclusion, the SATO 410e and 400e represent the pinnacle of label printing technology, combining high print quality, user-friendly interfaces, efficient connectivity, and robust performance. These printers are perfect for businesses looking to enhance their labeling processes and achieve operational excellence in their respective fields.
Top Page Image Contents