SATO 410e, 400e manual Multimeter Alone, Test Chart Module Dial Connector PIN Function

Page 72

Unit 5: Troubleshooting

TEST CHART

MODULE DIAL

CONNECTOR PIN

FUNCTION

 

 

 

 

1A

This test connector pin is used as the ground post.

 

 

 

 

2A

 

 

 

 

0

3A

Used to determine voltage of components that require between

+4.8 and +5.2 VDC to properly function.

 

 

 

 

 

1

4A

Used to determine voltage of components that require between

+11.4 and +12.6 VDC to properly function.

 

 

 

 

 

2

5A

Used to determine voltage of components that require between

-11.4 and -12.6 VDC to properly function.

 

 

 

 

 

3

6A

Used to determine voltage of components that require between

+23.5 and +24.5 VDC to properly function.

 

 

 

 

 

4

1B

Used in cunjunction with potentiometer VR2 to set the eye-mark

media sensor sensitivity.

 

 

 

 

 

5

2B

Used in cunjunction with potentiometer VR1 to set the gap or

center hole media sensor sensitivity.

 

 

 

 

 

6

3B

Used in cunjunction with potentiometer VR3 to set the ribbon

sensor sensitivity

 

 

 

 

 

7

4B

Used in cunjunction with potentiometer VR5 to set the edge-

hole media sensor sensitivity.

 

 

 

 

 

8

5B

Used in cunjunction with potentiometer VR6 to set the notched

tag media sensor sensitivity.

 

 

 

 

 

 

6B

Used in cunjunction with potentiometer VR7 to set jump sensor.

 

 

 

MULTIMETER ALONE

Testing of circuitry and sensor adjustment may be performed by using a multimeter without the assistance of the test module. To perform this task the multimeter probes must be attached to the correct connector pins of the test connector. Refer to the table above to correlate the desired testing or adjustment function with its relative connector pin. Afterward, refer to the table below to locate the required pins. Refer to the Adjustment Procedures chapter of the Operation unit for specific adjustment instructions if necessary and applicable.

6A

1A

6B

1B

Figure 5-2, Test Connector

SATO XL400-410e Operator Manual

PN 9001135A

Page 5-8

Page 71 Page 73
Image 72
Page 71 Page 73
Contents XL400e / XL410e Printers That may appear Table of Contents Troubleshooting OperationMaintenance Adjustment ProceduresPN 9001135A Introduction About this Manual Result in Presonal InjuryGeneral Description 1a, Primary ComponentsControl Features Buttons & Switches2b, Control Features Page Technical Data Physical Characteristics PowerEnvironmental ProcessingCharacter Font Capabilities BAR Code Capabilties Interface ModulesRegulatory Approvals Installation Unpacking & Parts Identification Unpacking and Parts IdentificationPrinter Installation Site LocationMedia Selection Media Loading 3a, Media Loading3b, Media Loading 3d, Media Loading Ribbon Loading 3f, Media Loading4a, Ribbon Loading 4c, Ribbon Loading 4e, Ribbon Loading 4g, Ribbon Loading RS232C Specifications Interface SelectionRS232 Serial Interface RS232C Serial Interface Signals PIN Direction Signal DefinitionCable Requirements DB9 Host Connection DB9 PrinterSpecifications IEEE1284 Parallel InterfaceACK Init802.11B Wireless 80211B Wireless SpecificationsUniversal Serial BUS USB Adapter Local Area Network LAN EthernetReceive Buffer ACK/NAK ProtocolAccessories Installation Pcmcia Memory UpgradeLabel Stacker Installation Stacker UnitOperation Printer Configuration DIP Switch PanelsDSW1 Default Settings DSW1 ConfigurationDSW1 Function Descriptions OFFDSW2 Default Settings DSW2 ConfigurationConfiguration DSW2 Function DescriptionsDSW3 Default Settings DSW1Function Description Configuration Modes Normal ModeTest Print Mode Test Print ModeAdvanced Mode Advanced ModeDefault Settings Mode Default Settings ModeFlash Memory Download Mode Download Font Deletion Status Description Acsii HEX TransferFlash Memory Download Mode User Download Mode User Download ModeHEX Dump Mode Hex Dump ModeCard Mode FeedNON-STANDARD Clear Mode Non-Standard Clear ModeService Mode 10a, Service Mode Test Print10b, Service Mode Sensor Level 10c, Service Mode Pitch Offset 10d, Service Mode Cut Offset 10e, Service Mode Backfeed Offset 10f, Service Mode Counter Display Normal Mode Default Settings ModeMenu Description NON-STANDARD Code ClearAdvanced Mode Flash Memory & User Download ModesCard Mode User Test Print ModeService Mode Operational Adjustments Potentiometer DESCRIPTION/PROCEDURE11, Adjustment Panel Cutter Sensor Positioning 14a, Cutter Sensor PositioningOperator Panel 15a, Tilting Operator PanelPowering OFF PrintingTest Printing Reloading MediaTroubleshooting Error Signals LED LCD Message Beep RemedyPrinter Troubleshooting No Printed Image Meandering MediaPrinter Creates a Blank Label Incorrect Label PositioningInterface Troubleshooting CHK Troubleshooting StepLAN Ehternet Interface Performance Testing Multimeter with Test ModuleTest Chart Module Dial Connector PIN Function Multimeter AloneTest Print Troubleshooting Hex Dump ModeTest Label Printing Sample Test Label Sensor Locations Sensor LocationsMaintenance Cleaning Procedures DamageReplacement Procedures Fuse ReplacementPrint Head Replacement Print Head to Prevent Damage to ITS ElementsRibbon Roller Replacement Ribbon Roller ReplacementAdjustment Procedures Print Defects Relative ProcedurePrint Head Balance Adjustment Print Head Balance AdjustmentPrint Head Alignment Print Head AlignmentPressure Roller Alignment Pressure Roller AlignmentPressure Roller Balance Pressure Roller BalanceRibbon Guide Adjustment Ribbon Guide AdjustmentRibbon Spindle Tensioning 10, Ribbon Spindle TensioningPitch Sensor Adjustment Label GAP & Center Hole Media Multimeter AlonePitch Sensor Adjustment EYE-MARK Media 11, Test Module & Sensor Potentiometers Pitch Sensor Adjustment R-CORNER Media Pitch Sensor Adjustment Side Hole Media Jump Hole Sensor Adjustment Ribbon Sensor Adjustment VR3Cutter Sensor Adjustment VR1SG / HO VR2

400e, 410e specifications

The SATO 410e and 400e are advanced thermal transfer printers designed for high-performance label printing in a variety of industries, including retail, logistics, and manufacturing. These models are renowned for their reliability, efficiency, and quality output, making them essential tools for businesses that demand precision and durability in their labeling processes.

One of the standout features of the SATO 410e and 400e is their exceptional print quality. They offer a resolution of up to 600 dpi, ensuring that even the most intricate details in barcodes, logos, and text are printed with clarity. This high resolution is crucial for applications that require precision, such as product labeling and inventory management.

The SATO 410e is equipped with an intuitive user interface that simplifies operation. Its LCD display provides real-time information about print status, and its control panel is designed for ease of navigation, reducing the learning curve for new users. On the other hand, the SATO 400e emphasizes compact design without compromising performance, making it an ideal choice for businesses with limited space or needing a mobile labeling solution.

Both models feature a robust set of connectivity options, including USB, Ethernet, and serial interfaces, allowing for seamless integration into existing IT infrastructures. This versatility makes them suitable for various deployment scenarios, whether used standalone or in networked environments.

In terms of speed, the SATO 410e and 400e are engineered to deliver rapid printing capabilities. The 410e can produce labels at a speed of up to 300 mm per second, while the 400e also showcases impressive speed without sacrificing quality. This capability is vital for high-volume printing tasks common in warehousing and distribution operations.

The technology behind these printers includes SATO’s innovative ARCP (Automatic Ribbon Control Path), which optimizes ribbon usage and minimizes waste, contributing to cost-effective printing solutions. Additionally, the SATO 410e and 400e support a wide range of media types and sizes, accommodating various labeling needs from small tags to large shipping labels.

Both models are also designed with durability in mind. They are built to withstand the rigors of industrial environments, ensuring longevity and consistent performance. With features like a strong casing and reliable internal components, users can expect these printers to maintain operational integrity even under demanding conditions.

In conclusion, the SATO 410e and 400e represent the pinnacle of label printing technology, combining high print quality, user-friendly interfaces, efficient connectivity, and robust performance. These printers are perfect for businesses looking to enhance their labeling processes and achieve operational excellence in their respective fields.
Top Page Image Contents