Star Micronics D6-IN manual Bios Setup Utility

Page 27

Chapter 4: The BIOS Setup Utility

Chapter

4

The BIOS Setup Utility

Configuration

After the D6-IN system board and all hardware is in- stalled, the system is ready for configuration. Before turning on the computer, make sure all cables are cor- rectly connected and all jumpers are correctly set.

It is recommended you keep the computer cover off the first time you boot the system. This will make it easier to correct any difficulties that might arise.

Initial Boot Up

Power up the D6-IN. If the system does not properly boot, check all your cables and peripherals for bad connections. You may also get beep codes or error messages. If this occurs, consult Appendices B and/or C for a guide to possible solutions.

After the system properly boots, it is ready to be config- ured. The following information explains the proper procedures for BIOS configuration.

Setup

The Setup program is used to configure the computer’s BIOS (Basic Input/Output System). The computer’s BIOS is responsible for configuring the system board and providing hardware information to the operating system. In order for the computer to run properly, run the Setup procedure after first installing the system board and whenever you make a hardware change to the system.

D6-IN System Board Manual

25

Page 26 Page 28
Image 27
Page 26 Page 28
Contents PCI/ISA D6-IN System Board Manual Copyright NoticesTable of Contents Bios Setup Utility Limited Warranty FCC Statement Declaration of Conformity List of Figures Introduction IntroductionFeatures Software Compatibility Common Names Before You BeginQuick Installation Installing the D6-INQuick Installation Power-Up Screen Configuring the D6-IN Configuring the D6-IND6-IN System Board D6-IN System Board2Jumper settings to reset the real-time clock Jumper SettingsIDE LED Configuring the D6-IN 3Case and peripheral connectionsIntroduction Installing the D6-INChassis with standard hardware Tools RequiredSIMMs Supported System MemoryMixing EDO and FPM Memory Bank Memory Configurations8MBx32/36 2MBx32/36 Removing SIMMs Installing the SIMMsPush the lever down until it locks into place Installing a CPUInstalling a PCI Card Installing a PCI Peripheral CardInstalling an ISA Peripheral Card Installing an ISA Peripheral CardBios Setup Utility SetupPower-Up Screen Setting the Main Screen Running the Setup ProcedureDiskette a or B IDE Adapters Hard Disk SetupVideo Bios System Time and DateExtended Memory System BiosExternal Cache System MemoryIDE Device Submenu Autotype Fixed DiskMultiple-Sector Transfers Transfer ModeSerial Port B Setting the Advanced ScreenSerial Port B Mode Serial Port aDiskette Controller Parallel Port ModeReset Configuration Data Parallel PortDram Type Large Disk Access ModeSupervisor Password User PasswordSecurity Screen Set User Password Set Supervisor PasswordSystem Backup Reminder Password on BootDiskette Access Fixed Disk Boot SectorPower Management Mode Power ScreenStandby CPU Speed Standby TimeoutSuspend Timeout Fixed Disk TimeoutStandby Break Events Mouse Wakeup EventPost Errors Boot ScreenBoot Sequence Setup PromptExit Screen Floppy CheckNumlock Specifications Multiple sector transfer support Environmental SpecificationsInfrared support for IrDA Two USB ports optionalBattery Disposal UK Technical Support Fax +44 01256 Technical SupportTechnical Support 510 Technical Support Fax RMA Department UK Technical SupportUK Technical Support BBS +44 Online ServicesAppendix a Technical Information D6-IN System Board Manual Messages, possible causes and solutions Appendix Post MessagesAppendix B Post Messages Cmos Following pages Is not installed or is failing, the system board willLCD read out showing the contents of port 80h Appendix C Beep and Post CodesGet in Post Reg Code One beep Appendix D Hard Disk Drive Types Hard Disk Drive TypesAppendix D Hard Disk Drive Types Appendix E Updating the System Bios Updating the System BiosAppendix E Updating the System Bios Appendix F Warranties and Notices Limited WarrantyNon-Warranty Service FCC Statement Declaration of Conformity Glossary GlossaryInternal Cache Cache which is built into the CPU. See Cache Glossary Glossary Battery Disposal Beep and Post Codes IndexIndex

D6-IN specifications

The Star Micronics D6-IN is a cutting-edge thermal printer designed to meet the demands of various industries, including retail, hospitality, and logistics. This printer exemplifies efficiency and versatility, making it an ideal choice for businesses that require reliable, high-quality printing solutions.

One of the main features of the D6-IN is its impressive printing speed. Capable of producing up to 200 mm per second, this printer ensures that receipts, labels, and other documents are generated quickly, helping to reduce customer wait times and enhance overall service efficiency. This speed does not come at the cost of print quality; the D6-IN delivers crisp and clear prints with a resolution of 203 dpi, ensuring that even the smallest text and intricate graphics are presented with exceptional clarity.

Another notable characteristic of the D6-IN is its robust connectivity options. This printer supports multiple interfaces, including USB, Ethernet, and Bluetooth, providing businesses with the flexibility to connect to a wide range of devices. Multi-device connectivity is essential in modern environments, facilitating seamless integration with point-of-sale systems, mobile devices, and other peripherals.

The D6-IN also features advanced technical capabilities, such as an embedded web server, which allows for easy configuration and monitoring of the printer over a network. This functionality ensures that businesses can manage their printing operations efficiently, making adjustments and diagnosing issues remotely when necessary.

The printer's compact design is another significant advantage, allowing it to fit easily into various workspaces without compromising performance. Its durable construction ensures that it can withstand the demands of busy environments, providing longevity and reliability that businesses can count on.

User-friendliness is a core design principle of the D6-IN, with features like drop-in paper loading, which simplifies the process of changing paper rolls. This ease of use results in minimal downtime and contributes to overall operational efficiency.

In summary, the Star Micronics D6-IN is a feature-rich thermal printer that combines speed, connectivity, and durability. Its exceptional print quality, versatile connectivity options, and user-friendly design make it an excellent choice for businesses looking to enhance their printing capabilities. With this printer, organizations can streamline their operations and provide better service to their customers, paving the way for increased productivity and success.
Top Page Image Contents