Star Micronics D6-IN manual Cmos

Page 52

Appendix B: POST Messages

Message

Possible Cause

Solution

 

 

 

MONITOR TYPE

Monitor type not

Run Setup and enter

DOES NOT MATCH

correctly identified in

correct monitor type.

CMOS

Setup.

 

 

 

 

OPERATING

Operating system

Check Setup to see if

SYSTEM NOT

cannot be located on

Drive A: and C: are

FOUND

Drive C: or Drive A:

properly configured, or

 

 

put a bootable disk in

 

 

Drive A:

 

 

 

PARITY CHECK 1

Parity error found in the

Check Setup. Board

nnnn

system bus.

repair may be required.

 

 

 

PARITY CHECK 2

Parity error found in the

Check Setup. Board

nnnn

I/O bus.

repair may be required.

 

 

 

PREVIOUS BOOT

Previous POST did not

Run Setup, load default

INCOMPLETE -

complete successfully.

BIOS settings, make any

DEFAULT

 

necessary adjustments,

CONFIGURATION

 

and save the changes

USED

 

 

 

 

 

REAL TIME CLOCK

Real-time clock failed

May require battery

ERROR

BIOS test.

replacement or board

 

 

repair.

 

 

 

SHADOW RAM

Shadow RAM failed.

May require repair of

FAILED AT OFFSET

 

system board.

 

 

 

SYSTEM BATTERY

System battery died.

Replace the system

IS DEAD

 

battery and run Setup to

 

 

reconfigure the system.

 

 

 

SYSTEM CACHE

External (L2) cache

System will still run, but

ERROR - CACHE

failed BIOS test.

slower. Replace cache

DISABLED

 

at convenience.

 

 

 

SYSTEM CMOS

System CMOS has been

Run Setup and

CHECKSUM BAD -

corrupted or modified

reconfigure the system.

RUN SETUP

incorrectly.

 

 

 

 

SYSTEM RAM

System RAM failed.

Replace defective RAM.

FAILED AT

 

 

OFFSET: nnnn

 

 

 

 

 

SYSTEM TIMER

Timer test failed.

Requires repair of system

ERROR

 

board.

 

 

 

 

 

 

50

D6-IN System Board Manual

Page 51 Page 53
Image 52
Page 51 Page 53
Contents PCI/ISA Copyright Notices D6-IN System Board ManualTable of Contents Bios Setup Utility Limited Warranty FCC Statement Declaration of Conformity List of Figures Introduction IntroductionFeatures Software Compatibility Before You Begin Common NamesInstalling the D6-IN Quick InstallationQuick Installation Power-Up Screen Configuring the D6-IN Configuring the D6-IND6-IN System Board D6-IN System BoardJumper Settings 2Jumper settings to reset the real-time clockConfiguring the D6-IN 3Case and peripheral connections IDE LEDInstalling the D6-IN IntroductionTools Required Chassis with standard hardwareSystem Memory SIMMs SupportedMixing EDO and FPM Memory Memory Configurations Bank8MBx32/36 2MBx32/36 Installing the SIMMs Removing SIMMsInstalling a CPU Push the lever down until it locks into placeInstalling a PCI Peripheral Card Installing a PCI CardInstalling an ISA Peripheral Card Installing an ISA Peripheral CardSetup Bios Setup UtilityPower-Up Screen Running the Setup Procedure Setting the Main ScreenIDE Adapters Hard Disk Setup Video BiosSystem Time and Date Diskette a or BSystem Bios External CacheSystem Memory Extended MemoryAutotype Fixed Disk IDE Device SubmenuTransfer Mode Multiple-Sector TransfersSetting the Advanced Screen Serial Port B ModeSerial Port a Serial Port BParallel Port Mode Reset Configuration DataParallel Port Diskette ControllerLarge Disk Access Mode Dram TypeUser Password Supervisor PasswordSecurity Screen Set Supervisor Password Set User PasswordPassword on Boot Diskette AccessFixed Disk Boot Sector System Backup ReminderPower Screen Power Management ModeStandby Timeout Suspend TimeoutFixed Disk Timeout Standby CPU SpeedMouse Wakeup Event Standby Break EventsBoot Screen Boot SequenceSetup Prompt Post ErrorsFloppy Check Exit ScreenNumlock Specifications Environmental Specifications Infrared support for IrDATwo USB ports optional Multiple sector transfer supportBattery Disposal Technical Support Technical Support 510 Technical Support Fax RMA DepartmentUK Technical Support UK Technical Support Fax +44 01256Online Services UK Technical Support BBS +44Appendix a Technical Information D6-IN System Board Manual Appendix Post Messages Messages, possible causes and solutionsAppendix B Post Messages Cmos Is not installed or is failing, the system board will LCD read out showing the contents of port 80hAppendix C Beep and Post Codes Following pagesGet in Post Reg Code One beep Hard Disk Drive Types Appendix D Hard Disk Drive TypesAppendix D Hard Disk Drive Types Updating the System Bios Appendix E Updating the System BiosAppendix E Updating the System Bios Limited Warranty Appendix F Warranties and NoticesNon-Warranty Service FCC Statement Declaration of Conformity Glossary GlossaryInternal Cache Cache which is built into the CPU. See Cache Glossary Glossary Index Battery Disposal Beep and Post CodesIndex

D6-IN specifications

The Star Micronics D6-IN is a cutting-edge thermal printer designed to meet the demands of various industries, including retail, hospitality, and logistics. This printer exemplifies efficiency and versatility, making it an ideal choice for businesses that require reliable, high-quality printing solutions.

One of the main features of the D6-IN is its impressive printing speed. Capable of producing up to 200 mm per second, this printer ensures that receipts, labels, and other documents are generated quickly, helping to reduce customer wait times and enhance overall service efficiency. This speed does not come at the cost of print quality; the D6-IN delivers crisp and clear prints with a resolution of 203 dpi, ensuring that even the smallest text and intricate graphics are presented with exceptional clarity.

Another notable characteristic of the D6-IN is its robust connectivity options. This printer supports multiple interfaces, including USB, Ethernet, and Bluetooth, providing businesses with the flexibility to connect to a wide range of devices. Multi-device connectivity is essential in modern environments, facilitating seamless integration with point-of-sale systems, mobile devices, and other peripherals.

The D6-IN also features advanced technical capabilities, such as an embedded web server, which allows for easy configuration and monitoring of the printer over a network. This functionality ensures that businesses can manage their printing operations efficiently, making adjustments and diagnosing issues remotely when necessary.

The printer's compact design is another significant advantage, allowing it to fit easily into various workspaces without compromising performance. Its durable construction ensures that it can withstand the demands of busy environments, providing longevity and reliability that businesses can count on.

User-friendliness is a core design principle of the D6-IN, with features like drop-in paper loading, which simplifies the process of changing paper rolls. This ease of use results in minimal downtime and contributes to overall operational efficiency.

In summary, the Star Micronics D6-IN is a feature-rich thermal printer that combines speed, connectivity, and durability. Its exceptional print quality, versatile connectivity options, and user-friendly design make it an excellent choice for businesses looking to enhance their printing capabilities. With this printer, organizations can streamline their operations and provide better service to their customers, paving the way for increased productivity and success.
Top Page Image Contents