Star Micronics D6-IN manual Get in Post Reg

Page 54

Appendix C: Beep and POST Codes

Code

Beeps

POST Routine Description

 

 

 

02

 

Verify Real Mode.

04

 

Get CPU type.

06

 

Initialize system hardware.

08

 

Initialize chipset registers with initial POST values.

09

 

Get in POST Reg.

0A

 

Initialize CPU registers.

0C

 

Initialize cache initial POST values.

OE

 

Initialize I/O.

OF

 

Initialize the localbus IDE.

10

 

Initialize Power Management.

11

 

Load alternate registers with initial POST values.

12

 

Jump to UserPatch0.

14

 

Initialize keyboard controller.

16

2-2-3

BIOS ROM checksum.

18

 

8254 timer initialization.

1A

 

8237 DMA controller initialization.

1C

 

Reset Programmable Interrupt Controller.

20

3-1-1

Test DRAM refresh.

22

3-1-3

Test 8742 Keyboard Controller.

24

 

Set ES segment register to 4 GB.

28

 

Autosize DRAM.

2A

 

Clear 512K base RAM.

2C

3-4-1

Test 512K base address lines.

2E

3-4-3

Test 512K base memory.

32

 

Test CPU bus-clock frequency.

34

 

Test CMOS RAM.

35

 

Initialize alternate chipset registers.

37

 

Reinitialize the chipset (MB only).

38

 

Shadow system BIOS ROM.

39

 

Reinitialize the cache (MB only).

3A

 

Autosize cache.

3C

 

Configure advanced chipset registers.

3D

 

Load alternate registers with CMOS values.

40

 

Set initial CPU speed.

42

 

Initialize interrupt vectors.

44

 

Initialize BIOS interrupts.

46

2-1-2-3

Check ROM copyright notice.

47

 

Initialize manager for PCI Option ROMs.

48

 

Check video configuration against CMOS.

49

 

Initialize PCI bus and devices.

 

 

 

52

D6-IN System Board Manual

Page 53 Page 55
Image 54
Page 53 Page 55
Contents PCI/ISA Copyright Notices D6-IN System Board ManualTable of Contents Bios Setup Utility Limited Warranty FCC Statement Declaration of Conformity List of Figures Introduction IntroductionFeatures Software Compatibility Before You Begin Common NamesQuick Installation Installing the D6-INQuick Installation Power-Up Screen Configuring the D6-IN Configuring the D6-IND6-IN System Board D6-IN System BoardJumper Settings 2Jumper settings to reset the real-time clockConfiguring the D6-IN 3Case and peripheral connections IDE LEDInstalling the D6-IN IntroductionTools Required Chassis with standard hardwareSystem Memory SIMMs SupportedMixing EDO and FPM Memory Memory Configurations Bank8MBx32/36 2MBx32/36 Installing the SIMMs Removing SIMMsInstalling a CPU Push the lever down until it locks into placeInstalling a PCI Peripheral Card Installing a PCI CardInstalling an ISA Peripheral Card Installing an ISA Peripheral CardSetup Bios Setup UtilityPower-Up Screen Running the Setup Procedure Setting the Main ScreenSystem Time and Date IDE Adapters Hard Disk SetupVideo Bios Diskette a or BSystem Memory System BiosExternal Cache Extended MemoryAutotype Fixed Disk IDE Device SubmenuTransfer Mode Multiple-Sector TransfersSerial Port a Setting the Advanced ScreenSerial Port B Mode Serial Port BParallel Port Parallel Port ModeReset Configuration Data Diskette ControllerLarge Disk Access Mode Dram TypeSupervisor Password User PasswordSecurity Screen Set Supervisor Password Set User PasswordFixed Disk Boot Sector Password on BootDiskette Access System Backup ReminderPower Screen Power Management ModeFixed Disk Timeout Standby TimeoutSuspend Timeout Standby CPU SpeedMouse Wakeup Event Standby Break EventsSetup Prompt Boot ScreenBoot Sequence Post ErrorsExit Screen Floppy CheckNumlock Specifications Two USB ports optional Environmental SpecificationsInfrared support for IrDA Multiple sector transfer supportBattery Disposal UK Technical Support Technical SupportTechnical Support 510 Technical Support Fax RMA Department UK Technical Support Fax +44 01256Online Services UK Technical Support BBS +44Appendix a Technical Information D6-IN System Board Manual Messages, possible causes and solutions Appendix Post MessagesAppendix B Post Messages Cmos Appendix C Beep and Post Codes Is not installed or is failing, the system board willLCD read out showing the contents of port 80h Following pagesGet in Post Reg Code One beep Hard Disk Drive Types Appendix D Hard Disk Drive TypesAppendix D Hard Disk Drive Types Updating the System Bios Appendix E Updating the System BiosAppendix E Updating the System Bios Limited Warranty Appendix F Warranties and NoticesNon-Warranty Service FCC Statement Declaration of Conformity Glossary GlossaryInternal Cache Cache which is built into the CPU. See Cache Glossary Glossary Battery Disposal Beep and Post Codes IndexIndex

D6-IN specifications

The Star Micronics D6-IN is a cutting-edge thermal printer designed to meet the demands of various industries, including retail, hospitality, and logistics. This printer exemplifies efficiency and versatility, making it an ideal choice for businesses that require reliable, high-quality printing solutions.

One of the main features of the D6-IN is its impressive printing speed. Capable of producing up to 200 mm per second, this printer ensures that receipts, labels, and other documents are generated quickly, helping to reduce customer wait times and enhance overall service efficiency. This speed does not come at the cost of print quality; the D6-IN delivers crisp and clear prints with a resolution of 203 dpi, ensuring that even the smallest text and intricate graphics are presented with exceptional clarity.

Another notable characteristic of the D6-IN is its robust connectivity options. This printer supports multiple interfaces, including USB, Ethernet, and Bluetooth, providing businesses with the flexibility to connect to a wide range of devices. Multi-device connectivity is essential in modern environments, facilitating seamless integration with point-of-sale systems, mobile devices, and other peripherals.

The D6-IN also features advanced technical capabilities, such as an embedded web server, which allows for easy configuration and monitoring of the printer over a network. This functionality ensures that businesses can manage their printing operations efficiently, making adjustments and diagnosing issues remotely when necessary.

The printer's compact design is another significant advantage, allowing it to fit easily into various workspaces without compromising performance. Its durable construction ensures that it can withstand the demands of busy environments, providing longevity and reliability that businesses can count on.

User-friendliness is a core design principle of the D6-IN, with features like drop-in paper loading, which simplifies the process of changing paper rolls. This ease of use results in minimal downtime and contributes to overall operational efficiency.

In summary, the Star Micronics D6-IN is a feature-rich thermal printer that combines speed, connectivity, and durability. Its exceptional print quality, versatile connectivity options, and user-friendly design make it an excellent choice for businesses looking to enhance their printing capabilities. With this printer, organizations can streamline their operations and provide better service to their customers, paving the way for increased productivity and success.
Top Page Image Contents