Star Micronics D6-IN manual Appendix Post Messages, Appendix B Post Messages

Page 51

Appendix B: POST Messages

Appendix POST Messages

 

The following table lists the Power On Self Test (POST)

B messages, possible causes and solutions.

 

Message

Possible Cause

Solution

 

 

 

 

 

DISKETTE DRIVE A

Drive A failed or is

Check Setup and cable

 

FAILURE

missing.

connections.

 

 

 

 

 

 

 

DISKETTE DRIVE B

Drive B failed or is

Check Setup and cable

 

FAILURE

 

missing.

connections.

 

 

 

 

 

 

 

EXTENDED RAM

Extended memory not

Replace defective

 

FAILED AT

working or configured

memory.

 

OFFSET: nnnn

 

properly.

 

 

 

 

 

 

 

 

 

FAILING BITS: nnnn

Memory failure in

Replace defective

 

 

 

 

System, Extended, or

memory.

 

 

Shadow memory.

 

 

 

 

 

 

FIXED DISK X

The hard disk is not

Rerun SETUP and check

 

FAILURE (where X

configured or working

connections, or replace

 

=0 or 1)

properly.

hard disk.

 

 

 

 

 

FIXED DISK

The controller card has

Check configuration and

 

CONTROLLER

failed.

connections, or replace

 

FAILURE

 

controller card.

 

 

 

 

 

INCORRECT DRIVE

Floppy drive A: not set

Run Setup.

 

A TYPE

 

correctly in Setup.

 

 

 

 

 

 

INCORRECT DRIVE

Floppy drive A: not set

Run Setup.

 

B TYPE

 

correctly in Setup.

 

 

 

 

 

 

 

 

 

INVALID NVRAM

NVRAM chip is bad.

Requires repair of system

 

MEDIA TYPE

 

 

board.

 

 

 

 

 

KEYBOARD

The keyboard or

Check connections. You

 

ERROR, or

 

keyboard controller

may have to replace the

 

KEYBOARD

 

failed.

keyboard or controller.

 

CONTROLLER

 

 

 

 

ERROR

 

 

 

KEYBOARD

A key is jammed or was

Make sure the keys are

 

ERROR nn

held down during boot.

not jammed or dirty.

 

 

 

 

 

KEYBOARD

Keyswitch on the front of

Unlock the keyswitch.

 

LOCKED

the case is locked.

 

 

 

 

 

D6-IN System Board Manual

49

Page 50 Page 52
Image 51
Page 50 Page 52
Contents PCI/ISA D6-IN System Board Manual Copyright NoticesTable of Contents Bios Setup Utility Limited Warranty FCC Statement Declaration of Conformity List of Figures Introduction IntroductionFeatures Software Compatibility Common Names Before You BeginQuick Installation Installing the D6-INQuick Installation Power-Up Screen Configuring the D6-IN Configuring the D6-IND6-IN System Board D6-IN System Board2Jumper settings to reset the real-time clock Jumper SettingsIDE LED Configuring the D6-IN 3Case and peripheral connectionsIntroduction Installing the D6-INChassis with standard hardware Tools RequiredSIMMs Supported System MemoryMixing EDO and FPM Memory Bank Memory Configurations8MBx32/36 2MBx32/36 Removing SIMMs Installing the SIMMsPush the lever down until it locks into place Installing a CPUInstalling a PCI Card Installing a PCI Peripheral CardInstalling an ISA Peripheral Card Installing an ISA Peripheral CardBios Setup Utility SetupPower-Up Screen Setting the Main Screen Running the Setup ProcedureDiskette a or B IDE Adapters Hard Disk SetupVideo Bios System Time and DateExtended Memory System BiosExternal Cache System MemoryIDE Device Submenu Autotype Fixed DiskMultiple-Sector Transfers Transfer ModeSerial Port B Setting the Advanced ScreenSerial Port B Mode Serial Port aDiskette Controller Parallel Port ModeReset Configuration Data Parallel PortDram Type Large Disk Access ModeSupervisor Password User PasswordSecurity Screen Set User Password Set Supervisor PasswordSystem Backup Reminder Password on BootDiskette Access Fixed Disk Boot SectorPower Management Mode Power ScreenStandby CPU Speed Standby TimeoutSuspend Timeout Fixed Disk TimeoutStandby Break Events Mouse Wakeup EventPost Errors Boot ScreenBoot Sequence Setup PromptExit Screen Floppy CheckNumlock Specifications Multiple sector transfer support Environmental SpecificationsInfrared support for IrDA Two USB ports optionalBattery Disposal UK Technical Support Fax +44 01256 Technical SupportTechnical Support 510 Technical Support Fax RMA Department UK Technical SupportUK Technical Support BBS +44 Online ServicesAppendix a Technical Information D6-IN System Board Manual Messages, possible causes and solutions Appendix Post MessagesAppendix B Post Messages Cmos Following pages Is not installed or is failing, the system board willLCD read out showing the contents of port 80h Appendix C Beep and Post CodesGet in Post Reg Code One beep Appendix D Hard Disk Drive Types Hard Disk Drive TypesAppendix D Hard Disk Drive Types Appendix E Updating the System Bios Updating the System BiosAppendix E Updating the System Bios Appendix F Warranties and Notices Limited WarrantyNon-Warranty Service FCC Statement Declaration of Conformity Glossary GlossaryInternal Cache Cache which is built into the CPU. See Cache Glossary Glossary Battery Disposal Beep and Post Codes IndexIndex

D6-IN specifications

The Star Micronics D6-IN is a cutting-edge thermal printer designed to meet the demands of various industries, including retail, hospitality, and logistics. This printer exemplifies efficiency and versatility, making it an ideal choice for businesses that require reliable, high-quality printing solutions.

One of the main features of the D6-IN is its impressive printing speed. Capable of producing up to 200 mm per second, this printer ensures that receipts, labels, and other documents are generated quickly, helping to reduce customer wait times and enhance overall service efficiency. This speed does not come at the cost of print quality; the D6-IN delivers crisp and clear prints with a resolution of 203 dpi, ensuring that even the smallest text and intricate graphics are presented with exceptional clarity.

Another notable characteristic of the D6-IN is its robust connectivity options. This printer supports multiple interfaces, including USB, Ethernet, and Bluetooth, providing businesses with the flexibility to connect to a wide range of devices. Multi-device connectivity is essential in modern environments, facilitating seamless integration with point-of-sale systems, mobile devices, and other peripherals.

The D6-IN also features advanced technical capabilities, such as an embedded web server, which allows for easy configuration and monitoring of the printer over a network. This functionality ensures that businesses can manage their printing operations efficiently, making adjustments and diagnosing issues remotely when necessary.

The printer's compact design is another significant advantage, allowing it to fit easily into various workspaces without compromising performance. Its durable construction ensures that it can withstand the demands of busy environments, providing longevity and reliability that businesses can count on.

User-friendliness is a core design principle of the D6-IN, with features like drop-in paper loading, which simplifies the process of changing paper rolls. This ease of use results in minimal downtime and contributes to overall operational efficiency.

In summary, the Star Micronics D6-IN is a feature-rich thermal printer that combines speed, connectivity, and durability. Its exceptional print quality, versatile connectivity options, and user-friendly design make it an excellent choice for businesses looking to enhance their printing capabilities. With this printer, organizations can streamline their operations and provide better service to their customers, paving the way for increased productivity and success.
Top Page Image Contents