Star Micronics D6-IN manual Internal Cache Cache which is built into the CPU. See Cache

Page 66

Glossary

functions by spinning at high speed while moving a device called the read/ write head across the disk’s surface in order to read or write data in mag- netic code.

DRAM - An acronym for Dynamic Random Access Memory. A type of memory chip that only keeps its memory if supplied with regular clock pulses and a chance to regularly re- fresh its data. It is slower and more cost effective than SRAM. See SRAM.

ECC - An acronym for Error Check- ing and Correction. ECC enables par- ity checking and can detect and cor- rect memory errors on the system board.

ECP - An acronym for Extended Ca- pabilities Port. A standard set by Hewlett Packard and Microsoft Cor- poration to expand the capabilities of the parallel port.

EDO Memory - An acronym for Ex- tended Data Out. A type of DRAM with built-in cache for enhanced per- formance.

EISA - An acronym for Extended In- dustry Standard Architecture. EISA is a bus design standard which is fully backward compatible with the ISA bus. Although it is a 32-bit bus, it only runs at 8MHz. See PCI, VESA Local Bus and ISA.

EPP - An acronym for Enhanced Par- allel Port. A standard which increases the capabilities of the parallel port.

EPROM - Acronym for Erasable Pro- grammable Read Only Memory. A type of ROM chip that can be pro- grammed with relatively simple tools that will retain its data until erased. It can only be erased by exposing the cir- cuitry in the chip to ultraviolet light. See also Flash ROM.

Flash ROM - A type of ROM chip that will retain its data until erased. It can be erased or reprogrammed by supplying it with +12V of voltage. See ROM and EPROM.

Gigabyte - A disk storage capacity measurement. Approximately one thousand megabytes or 1,073,741,824 bytes.

IDE - An acronym for Integrated De- vice Electronics. A standard for com- municating between a hard drive and a computer.

Internal Cache - Cache which is built into the CPU. See Cache.

ISA - An acronym for Industry Stan- dard Architecture. A well-established bus standard that originated with the IBM AT. See PCI, VESA Local Bus and EISA.

Parallel - A form of data transmission in which the data is sent one byte at a time over several wires that each carry one byte. In parallel transmission, all the bytes arrive simultaneously, as op- posed to serial transmission in which bits arrive one by one.

64

D6-IN System Board Manual

Page 65 Page 67
Image 66
Page 65 Page 67
Contents PCI/ISA Copyright Notices D6-IN System Board ManualTable of Contents Bios Setup Utility Limited Warranty FCC Statement Declaration of Conformity List of Figures Introduction IntroductionFeatures Software Compatibility Before You Begin Common NamesQuick Installation Installing the D6-INQuick Installation Power-Up Screen Configuring the D6-IN Configuring the D6-IND6-IN System Board D6-IN System BoardJumper Settings 2Jumper settings to reset the real-time clockConfiguring the D6-IN 3Case and peripheral connections IDE LEDInstalling the D6-IN IntroductionTools Required Chassis with standard hardwareSystem Memory SIMMs SupportedMixing EDO and FPM Memory Memory Configurations Bank8MBx32/36 2MBx32/36 Installing the SIMMs Removing SIMMsInstalling a CPU Push the lever down until it locks into placeInstalling a PCI Peripheral Card Installing a PCI CardInstalling an ISA Peripheral Card Installing an ISA Peripheral CardSetup Bios Setup UtilityPower-Up Screen Running the Setup Procedure Setting the Main ScreenSystem Time and Date IDE Adapters Hard Disk SetupVideo Bios Diskette a or BSystem Memory System BiosExternal Cache Extended MemoryAutotype Fixed Disk IDE Device SubmenuTransfer Mode Multiple-Sector TransfersSerial Port a Setting the Advanced ScreenSerial Port B Mode Serial Port BParallel Port Parallel Port ModeReset Configuration Data Diskette ControllerLarge Disk Access Mode Dram TypeSupervisor Password User PasswordSecurity Screen Set Supervisor Password Set User PasswordFixed Disk Boot Sector Password on BootDiskette Access System Backup ReminderPower Screen Power Management ModeFixed Disk Timeout Standby TimeoutSuspend Timeout Standby CPU SpeedMouse Wakeup Event Standby Break EventsSetup Prompt Boot ScreenBoot Sequence Post ErrorsExit Screen Floppy CheckNumlock Specifications Two USB ports optional Environmental SpecificationsInfrared support for IrDA Multiple sector transfer supportBattery Disposal UK Technical Support Technical SupportTechnical Support 510 Technical Support Fax RMA Department UK Technical Support Fax +44 01256Online Services UK Technical Support BBS +44Appendix a Technical Information D6-IN System Board Manual Messages, possible causes and solutions Appendix Post MessagesAppendix B Post Messages Cmos Appendix C Beep and Post Codes Is not installed or is failing, the system board willLCD read out showing the contents of port 80h Following pagesGet in Post Reg Code One beep Hard Disk Drive Types Appendix D Hard Disk Drive TypesAppendix D Hard Disk Drive Types Updating the System Bios Appendix E Updating the System BiosAppendix E Updating the System Bios Limited Warranty Appendix F Warranties and NoticesNon-Warranty Service FCC Statement Declaration of Conformity Glossary GlossaryInternal Cache Cache which is built into the CPU. See Cache Glossary Glossary Battery Disposal Beep and Post Codes IndexIndex

D6-IN specifications

The Star Micronics D6-IN is a cutting-edge thermal printer designed to meet the demands of various industries, including retail, hospitality, and logistics. This printer exemplifies efficiency and versatility, making it an ideal choice for businesses that require reliable, high-quality printing solutions.

One of the main features of the D6-IN is its impressive printing speed. Capable of producing up to 200 mm per second, this printer ensures that receipts, labels, and other documents are generated quickly, helping to reduce customer wait times and enhance overall service efficiency. This speed does not come at the cost of print quality; the D6-IN delivers crisp and clear prints with a resolution of 203 dpi, ensuring that even the smallest text and intricate graphics are presented with exceptional clarity.

Another notable characteristic of the D6-IN is its robust connectivity options. This printer supports multiple interfaces, including USB, Ethernet, and Bluetooth, providing businesses with the flexibility to connect to a wide range of devices. Multi-device connectivity is essential in modern environments, facilitating seamless integration with point-of-sale systems, mobile devices, and other peripherals.

The D6-IN also features advanced technical capabilities, such as an embedded web server, which allows for easy configuration and monitoring of the printer over a network. This functionality ensures that businesses can manage their printing operations efficiently, making adjustments and diagnosing issues remotely when necessary.

The printer's compact design is another significant advantage, allowing it to fit easily into various workspaces without compromising performance. Its durable construction ensures that it can withstand the demands of busy environments, providing longevity and reliability that businesses can count on.

User-friendliness is a core design principle of the D6-IN, with features like drop-in paper loading, which simplifies the process of changing paper rolls. This ease of use results in minimal downtime and contributes to overall operational efficiency.

In summary, the Star Micronics D6-IN is a feature-rich thermal printer that combines speed, connectivity, and durability. Its exceptional print quality, versatile connectivity options, and user-friendly design make it an excellent choice for businesses looking to enhance their printing capabilities. With this printer, organizations can streamline their operations and provide better service to their customers, paving the way for increased productivity and success.
Top Page Image Contents