Star Micronics NX-2420 user manual On Line button, Paper Feed button

Page 32

ON LINE button

The ( ONLINE ) button sets the printer on-line and off-line. The status changes each time you press the button.

When the printer is on-line, it can receive and print data from the computer. When the printer is off-line, it stops printing and sends the computer a signal indicating that it cannot accept data.

The printer powers up in the on-line status if paper is loaded, If paper is not loaded, the printer powers up off-line with the POWER indicator flashing. When you load paper, the POWER indicator stops flashing, and the printer goes on-line.

You will want to press the ( ON LINE ) button:

•Before and after any other panel operation

The other panel buttons operate only in the off-line state. Press the ( ON LINE > button to go off-line. After performing the panel operation(s), press the ( ON LINE ) button again to go back on-line.

•To pause during printing

If you press the ( ON LINE ) button during printing, the printer stops printing and goes off-line, allowing you to check the printout or change a control panel setting. Printing resumes when you press the ( ON LINE ) button again to go back on-line.

•To cut fanfold forms at the end of printing

When using fanfold forms, you can hold the ( ON LINE > button down for one second. In addition to going off-line, the printer also feeds the

paper forward approximately two inches. This allows you to cut it off just - below the last line printed.

When you press the ( ON LINE ) button again to go back on-line, the paper feeds backward stopping where you left off.

NOTE:This function is valid only when the buffer is empty.

PAPER FEED button

If you press this button while off-line, the paper will feed forward. If you hold the button down, the printer will perform consecutive line feeds.

24

Page 31 Page 33
Image 32
Page 31 Page 33
Contents NX-2420 Above statement applies only IOprinkrs marketed in the USA HOW to USE this Manual Page Features of the Printer Table of Contents Default Settings Specifications Chapter Checking the carton contents Den tifying printer parts Printer’s external partsInstalling the ribbon cartridge and the roller unit Mounting the platen knobFigum 1-4. Removing the top cover Page Hgure 1-7. Install the roller unit onto the printer Slide the cartridge into the slot with the power switch off Ins falling the optional cartridgeConnecting the printer to your computer Connecting the interface cableAutomatic loading Loading Single SheetsFigure I-17. Loading a single sheet Manual loading Loading and Parking Fanfold Forms Loading the paper from the rear of the printerPage 75.Mounting the paper guide for fanfold forms Loading the paper from the bottom of the printer Figure l-16.Pull up the tractor unit for bottom feedingPaper parking Paper unparking Loading MULTI-PART Forms Adjusting the Printing GAP Paper Type Weight Memo Control Panel Operations On Line button Paper Feed buttonSET/EJECT/PARK button Pitch buttonFont button Short test mode POWER-UP FunctionsLong test mode Print area test mode Stay in Panel PitchStay in Panel Font Stay in Panel Pitch and FontHexadecimal dump Lprint CHR$I NextOUT &H3BC,I OUT &H3BE,S OUT &H3BE,J Return Form feed Top of formChanging the auto loading value Forward micro-feedReverse micro-feed Clearing the buffer/All reset Selecting the print color Store Macro DefinitionPage Default Settings Functions of the EDS SElTlNGS Page 1OCPIDRAFT 1OCPIHS Draft OFF 17CPIDRAFT Page LoFFloFFloml Bidirectional TEST/ADJUSTMENT Mode Raft On LNE Printer Control Commands Select draft quality characters Select draft pica charactersSelect draft elite characters Select draft condensed charactersSelect Characters Select LQ pica charactersSelect LQ elite characters Select LQ condensed CharactersSelect font Select LQ proportional CharactersSelect LQ font Cancel emphasized printing Select italic CharactersSelect upright characters Emphasized printingCancel double-s trike printing Start underliningStop underlining Starf VerliningSuperscript Select scoreSelect ornament character Cancel superscript or subscript SubscriptSelect standard character set Select IBM character setSelect international character set Select character Set #ISelect character set #2 Select IBM code Enable printing of all character codesEnable printing of all character codes on next character Select slash zero Select normal zeroPica pitch Elite pitchCancel condensed printing Cancel expanded printingSemi-condensed Condensed printingCancel one-line expanded printing Expanded printing for one lineSelect character width Select proportional spacingIncrease character spacing Select master print modeSelect fixed spacing Print double-height characters Select double or quadruple sizeSelect character size Return to normal height Select character height, width, and line spacingSet line spacing to l/8 inch Set line spacing to 7160or 7/72 inchSet line spacing to l/6 inch Set line spacing to n/360 inchSet line spacing to n/60 inch or n/72 inch Set base unit for line spacingSet line spacing to n/180 inch or n/216 inch Select forward feed mode Select reverse feed modeExecute ES Line feedPerform one n/l804nch or n/216=inch line feed Perform one n/180-inch reverse line feedFeed paper n lines Set top of page at current positionSet bottom margin Cancel bottom marginSet page length to n inches Disable paper-out detector Enable paper-out detectorReturn to top of current Set vertical tab stopsSet vertical tab stops every n lines Set vertical tab stops in channelSelect vertical tab channel Vertical tabSet left margin Set right marginCancel automa tic line feed Set left and right marginsCarriage return Set automatic line feedLeft justify Center textRight justify Full justifyReset all tab stops Set horizontal tab stopsSet horizontal tab stops every n columns Horizontal TabRelative horizontal Tab Relative horizontal tab in inchesAbsolute horizontal tab in inches Absolute horizontal tab in columnsPrint normal-density g-bit graphics Print double-density g-bit graphicsPrint double-density, double-speed g-bit graphics Print quadruple-density g-bit graphicsSe/ect graphics mode Print hex-density 24-bit graphicsSeiecf graphics mode Convert graphics DensityDefine download characters ?n4 Shift download character area Copy character set from ROM into RAMSelect download character set Select draft pica download character set Select draft elite download character setSelect draft condensed download characters Select LQ pica download charactersSelect L Q elite download characters Select LQ condensed download charactersSelect LQ proportional download characters Select ROM character setSelect print color Set MSB toCancel last line Accept MSB as isDelete last character sent Set printer off-lineStop printing BellBidirectional printing Unidirectional printingReset printer Manual feedAuto feed Eject paper from ASF

NX-2420 specifications

The Star Micronics NX-2420 is a leading-edge thermal printer designed to meet the diverse demands of modern businesses. Renowned for its compact design and robust build, the NX-2420 excels in performance and versatility, making it an ideal choice for retail, hospitality, and various other industries.

One of the standout features of the NX-2420 is its high-speed printing capability. With a print speed of up to 200 millimeters per second, it ensures that transactions are completed promptly, delivering receipts and labels without delay. This efficiency helps businesses provide superior customer service, especially during peak hours.

The NX-2420 supports multiple paper widths, accommodating various label and receipt sizes. This flexibility allows businesses to tailor their printing solutions to fit specific needs, whether they require larger labels for shipping or smaller receipts for purchases. The printer also utilizes direct thermal printing technology, eliminating the need for ink or toner. This not only reduces ongoing operational costs but also minimizes maintenance efforts, making it a user-friendly option.

Connectivity is a crucial aspect of the NX-2420. It offers a range of connectivity options, including USB, Ethernet, and Bluetooth, enabling seamless integration with existing systems and wireless printing from mobile devices. This flexibility is particularly beneficial for businesses that utilize point-of-sale (POS) systems and want to enhance their overall operational efficiency.

Another notable characteristic of the NX-2420 is its durability. Built to withstand the rigors of a busy environment, this printer features a robust casing and is designed to handle high-volume printing tasks. Furthermore, it operates quietly, contributing to a more pleasant working atmosphere for staff and customers alike.

In addition to standard printing capabilities, the NX-2420 is also equipped with advanced features such as an integrated cutter for precise label cutting and an optional built-in camera that enhances functionality in specific applications. This adaptability makes the NX-2420 suitable for a wide range of scenarios, from retail checkout counters to inventory management systems.

In conclusion, the Star Micronics NX-2420 is an exceptional thermal printer that combines speed, durability, and versatility. With its array of features and technologies, it stands out as a reliable choice for businesses looking to enhance their printing solutions and improve operational efficiency. Whether for creating receipts, labels, or tickets, the NX-2420 is poised to meet the demands of today's dynamic business environment.
Top Page Image Contents