Star Micronics NX-2420 Forward micro-feed, Reverse micro-feed, Changing the auto loading value

Page 41

3.Press and hold the ( ON LINE > button.

4.While holding the ( ON LINE )button down, press the (PITCH)button, then release both buttons at the same time. The printer will beep to indicate that the top-of-form position has been set.

Forward micro-feed

For fine alignment, you can feed the paper forward in very small increments as follows:

1.Press the ( ON LINE ) button to set the printer off-line.

2.Press the ( ON LINE ) button again and hold it down.

3.While holding the ( ON LINE ) button down, press the (PAPERFEED) button. The paper will start advancing in a series of small steps. When you want to stop, release both buttons.

Reverse micro-feed

You can also feed the paper in small increments in reverse, to return to a higher position on the same page.

NOTE: With fanfold forms, do not try to rctum to a previous page. The per- foration may catch inside the printer and cause a jam.

1.Press the ( ON LINE ) button to set the printer off-line.

2.Press the ( ON LINE ) button again and hold it down.

3.While holding the ( ON LINE ) button down, press the ( =u+E=’ ) button. The paper will start moving backwards in a series of small steps. When you want to stop, rclcasc both buttons.

Changing the auto loading value

Normally, the printer automatically loads the paper one line from the top edge.

If you want to change this value, follow this procedure:

1.Load the paper using the ( Sy&~CT ) button.

2.Change the print position using the micro feed function.

The line on the card holder helps you to align the baseline of characters to be printed.

3.After you get the desired position, press the ( ON LINE ) button to save the value.

Page 40 Page 42
Image 41
Page 40 Page 42
Contents NX-2420 Above statement applies only IOprinkrs marketed in the USA HOW to USE this Manual Page Features of the Printer Table of Contents Default Settings Specifications Chapter Checking the carton contents Printer’s external parts Den tifying printer partsMounting the platen knob Installing the ribbon cartridge and the roller unitFigum 1-4. Removing the top cover Page Hgure 1-7. Install the roller unit onto the printer Ins falling the optional cartridge Slide the cartridge into the slot with the power switch offConnecting the interface cable Connecting the printer to your computerLoading Single Sheets Automatic loadingFigure I-17. Loading a single sheet Manual loading Loading the paper from the rear of the printer Loading and Parking Fanfold FormsPage 75.Mounting the paper guide for fanfold forms Figure l-16.Pull up the tractor unit for bottom feeding Loading the paper from the bottom of the printerPaper parking Paper unparking Loading MULTI-PART Forms Adjusting the Printing GAP Paper Type Weight Memo Control Panel Operations Paper Feed button On Line buttonPitch button SET/EJECT/PARK buttonFont button POWER-UP Functions Short test modeLong test mode Stay in Panel Pitch Print area test modeStay in Panel Font Stay in Panel Pitch and FontLprint CHR$I Next Hexadecimal dumpOUT &H3BC,I OUT &H3BE,S OUT &H3BE,J Return Top of form Form feedChanging the auto loading value Forward micro-feedReverse micro-feed Clearing the buffer/All reset Store Macro Definition Selecting the print colorPage Default Settings Functions of the EDS SElTlNGS Page 1OCPIDRAFT 1OCPIHS Draft OFF 17CPIDRAFT Page LoFFloFFloml Bidirectional TEST/ADJUSTMENT Mode Raft On LNE Printer Control Commands Select draft pica characters Select draft quality charactersSelect draft elite characters Select draft condensed charactersSelect LQ pica characters Select CharactersSelect LQ elite characters Select LQ condensed CharactersSelect font Select LQ proportional CharactersSelect LQ font Select italic Characters Cancel emphasized printingSelect upright characters Emphasized printingStart underlining Cancel double-s trike printingStop underlining Starf VerliningSuperscript Select scoreSelect ornament character Subscript Cancel superscript or subscriptSelect standard character set Select IBM character setSelect international character set Select character Set #ISelect character set #2 Select IBM code Enable printing of all character codesEnable printing of all character codes on next character Select normal zero Select slash zeroPica pitch Elite pitchCancel expanded printing Cancel condensed printingSemi-condensed Condensed printingExpanded printing for one line Cancel one-line expanded printingSelect character width Select proportional spacingIncrease character spacing Select master print modeSelect fixed spacing Print double-height characters Select double or quadruple sizeSelect character size Select character height, width, and line spacing Return to normal heightSet line spacing to 7160or 7/72 inch Set line spacing to l/8 inchSet line spacing to l/6 inch Set line spacing to n/360 inchSet line spacing to n/60 inch or n/72 inch Set base unit for line spacingSet line spacing to n/180 inch or n/216 inch Select reverse feed mode Select forward feed modeExecute ES Line feedPerform one n/180-inch reverse line feed Perform one n/l804nch or n/216=inch line feedFeed paper n lines Set top of page at current positionSet bottom margin Cancel bottom marginSet page length to n inches Enable paper-out detector Disable paper-out detectorReturn to top of current Set vertical tab stopsSet vertical tab stops in channel Set vertical tab stops every n linesSelect vertical tab channel Vertical tabSet right margin Set left marginSet left and right margins Cancel automa tic line feedCarriage return Set automatic line feedCenter text Left justifyRight justify Full justifySet horizontal tab stops Reset all tab stopsSet horizontal tab stops every n columns Horizontal TabRelative horizontal tab in inches Relative horizontal TabAbsolute horizontal tab in inches Absolute horizontal tab in columnsPrint double-density g-bit graphics Print normal-density g-bit graphicsPrint double-density, double-speed g-bit graphics Print quadruple-density g-bit graphicsPrint hex-density 24-bit graphics Se/ect graphics modeConvert graphics Density Seiecf graphics modeDefine download characters ?n4 Shift download character area Copy character set from ROM into RAMSelect download character set Select draft elite download character set Select draft pica download character setSelect draft condensed download characters Select LQ pica download charactersSelect LQ condensed download characters Select L Q elite download charactersSelect LQ proportional download characters Select ROM character setSet MSB to Select print colorAccept MSB as is Cancel last lineDelete last character sent Set printer off-lineBell Stop printingBidirectional printing Unidirectional printingManual feed Reset printerAuto feed Eject paper from ASF

NX-2420 specifications

The Star Micronics NX-2420 is a leading-edge thermal printer designed to meet the diverse demands of modern businesses. Renowned for its compact design and robust build, the NX-2420 excels in performance and versatility, making it an ideal choice for retail, hospitality, and various other industries.

One of the standout features of the NX-2420 is its high-speed printing capability. With a print speed of up to 200 millimeters per second, it ensures that transactions are completed promptly, delivering receipts and labels without delay. This efficiency helps businesses provide superior customer service, especially during peak hours.

The NX-2420 supports multiple paper widths, accommodating various label and receipt sizes. This flexibility allows businesses to tailor their printing solutions to fit specific needs, whether they require larger labels for shipping or smaller receipts for purchases. The printer also utilizes direct thermal printing technology, eliminating the need for ink or toner. This not only reduces ongoing operational costs but also minimizes maintenance efforts, making it a user-friendly option.

Connectivity is a crucial aspect of the NX-2420. It offers a range of connectivity options, including USB, Ethernet, and Bluetooth, enabling seamless integration with existing systems and wireless printing from mobile devices. This flexibility is particularly beneficial for businesses that utilize point-of-sale (POS) systems and want to enhance their overall operational efficiency.

Another notable characteristic of the NX-2420 is its durability. Built to withstand the rigors of a busy environment, this printer features a robust casing and is designed to handle high-volume printing tasks. Furthermore, it operates quietly, contributing to a more pleasant working atmosphere for staff and customers alike.

In addition to standard printing capabilities, the NX-2420 is also equipped with advanced features such as an integrated cutter for precise label cutting and an optional built-in camera that enhances functionality in specific applications. This adaptability makes the NX-2420 suitable for a wide range of scenarios, from retail checkout counters to inventory management systems.

In conclusion, the Star Micronics NX-2420 is an exceptional thermal printer that combines speed, durability, and versatility. With its array of features and technologies, it stands out as a reliable choice for businesses looking to enhance their printing solutions and improve operational efficiency. Whether for creating receipts, labels, or tickets, the NX-2420 is poised to meet the demands of today's dynamic business environment.
Top Page Image Contents