Star Micronics NX-2420 user manual Chapter

Page 9

Chapter 1

SETTING UP THE PRINTER

Subjects covered in Chapter 1 include -

. Locating the printer

. Unpacking and inspection (part names)

•Setting up and connecting

•Loading single sheets

•Loading and parking fanfold forms

. Adjusting the printing gap

LOCATING THE PRINTER

Before you start unpacking and setting up your printer, make sure that you have a suitable place on which to locate it. By “a suitable place”, we mean:

•A firm, level surface which is fairly vibration-free

•Away from excessive heat (such as direct sunlight, hearers, etc)

•Away from excessive humidity

•Away from excessive dust

•Supply it with “clean” electricity. Do not connect it to the same circuit as a large, noise-producing appliance such as a refrigerator.

. Make sure the line voltage is the voltage specified on the printer’s identification plate.

•To disconnect the printer the plug has to be disconnected from the wall socket, which has to be located close to the printer, and easy to access.

. Install the printer where there is sufficient room for the paper and any paper being fed in or printed out.

•If you are connecting your printer with a parallel cable, make sure that the cable is within 2m (6ft) of the printer. An RS-232 connection using the optional SPC-8K interface can be made over longer distances.

Page 8 Page 10
Image 9
Page 8 Page 10
Contents NX-2420 Above statement applies only IOprinkrs marketed in the USA HOW to USE this Manual Page Features of the Printer Table of Contents Default Settings Specifications Chapter Checking the carton contents Printer’s external parts Den tifying printer partsMounting the platen knob Installing the ribbon cartridge and the roller unitFigum 1-4. Removing the top cover Page Hgure 1-7. Install the roller unit onto the printer Ins falling the optional cartridge Slide the cartridge into the slot with the power switch offConnecting the interface cable Connecting the printer to your computerLoading Single Sheets Automatic loadingFigure I-17. Loading a single sheet Manual loading Loading the paper from the rear of the printer Loading and Parking Fanfold FormsPage 75.Mounting the paper guide for fanfold forms Figure l-16.Pull up the tractor unit for bottom feeding Loading the paper from the bottom of the printerPaper parking Paper unparking Loading MULTI-PART Forms Adjusting the Printing GAP Paper Type Weight Memo Control Panel Operations Paper Feed button On Line buttonPitch button SET/EJECT/PARK buttonFont button POWER-UP Functions Short test modeLong test mode Stay in Panel Pitch Print area test modeStay in Panel Font Stay in Panel Pitch and FontLprint CHR$I Next Hexadecimal dumpOUT &H3BC,I OUT &H3BE,S OUT &H3BE,J Return Top of form Form feedForward micro-feed Reverse micro-feedChanging the auto loading value Clearing the buffer/All reset Store Macro Definition Selecting the print colorPage Default Settings Functions of the EDS SElTlNGS Page 1OCPIDRAFT 1OCPIHS Draft OFF 17CPIDRAFT Page LoFFloFFloml Bidirectional TEST/ADJUSTMENT Mode Raft On LNE Printer Control Commands Select draft pica characters Select draft quality charactersSelect draft elite characters Select draft condensed charactersSelect LQ pica characters Select CharactersSelect LQ elite characters Select LQ condensed CharactersSelect LQ proportional Characters Select LQ fontSelect font Select italic Characters Cancel emphasized printingSelect upright characters Emphasized printingStart underlining Cancel double-s trike printingStop underlining Starf VerliningSelect score Select ornament characterSuperscript Subscript Cancel superscript or subscriptSelect standard character set Select IBM character setSelect character Set #I Select character set #2Select international character set Enable printing of all character codes Enable printing of all character codes on next characterSelect IBM code Select normal zero Select slash zeroPica pitch Elite pitchCancel expanded printing Cancel condensed printingSemi-condensed Condensed printingExpanded printing for one line Cancel one-line expanded printingSelect character width Select proportional spacingSelect master print mode Select fixed spacingIncrease character spacing Select double or quadruple size Select character sizePrint double-height characters Select character height, width, and line spacing Return to normal heightSet line spacing to 7160or 7/72 inch Set line spacing to l/8 inchSet line spacing to l/6 inch Set line spacing to n/360 inchSet base unit for line spacing Set line spacing to n/180 inch or n/216 inchSet line spacing to n/60 inch or n/72 inch Select reverse feed mode Select forward feed modeExecute ES Line feedPerform one n/180-inch reverse line feed Perform one n/l804nch or n/216=inch line feedFeed paper n lines Set top of page at current positionCancel bottom margin Set page length to n inchesSet bottom margin Enable paper-out detector Disable paper-out detectorReturn to top of current Set vertical tab stopsSet vertical tab stops in channel Set vertical tab stops every n linesSelect vertical tab channel Vertical tabSet right margin Set left marginSet left and right margins Cancel automa tic line feedCarriage return Set automatic line feedCenter text Left justifyRight justify Full justifySet horizontal tab stops Reset all tab stopsSet horizontal tab stops every n columns Horizontal TabRelative horizontal tab in inches Relative horizontal TabAbsolute horizontal tab in inches Absolute horizontal tab in columnsPrint double-density g-bit graphics Print normal-density g-bit graphicsPrint double-density, double-speed g-bit graphics Print quadruple-density g-bit graphicsPrint hex-density 24-bit graphics Se/ect graphics modeConvert graphics Density Seiecf graphics modeDefine download characters ?n4 Copy character set from ROM into RAM Select download character setShift download character area Select draft elite download character set Select draft pica download character setSelect draft condensed download characters Select LQ pica download charactersSelect LQ condensed download characters Select L Q elite download charactersSelect LQ proportional download characters Select ROM character setSet MSB to Select print colorAccept MSB as is Cancel last lineDelete last character sent Set printer off-lineBell Stop printingBidirectional printing Unidirectional printingManual feed Reset printerAuto feed Eject paper from ASF

NX-2420 specifications

The Star Micronics NX-2420 is a leading-edge thermal printer designed to meet the diverse demands of modern businesses. Renowned for its compact design and robust build, the NX-2420 excels in performance and versatility, making it an ideal choice for retail, hospitality, and various other industries.

One of the standout features of the NX-2420 is its high-speed printing capability. With a print speed of up to 200 millimeters per second, it ensures that transactions are completed promptly, delivering receipts and labels without delay. This efficiency helps businesses provide superior customer service, especially during peak hours.

The NX-2420 supports multiple paper widths, accommodating various label and receipt sizes. This flexibility allows businesses to tailor their printing solutions to fit specific needs, whether they require larger labels for shipping or smaller receipts for purchases. The printer also utilizes direct thermal printing technology, eliminating the need for ink or toner. This not only reduces ongoing operational costs but also minimizes maintenance efforts, making it a user-friendly option.

Connectivity is a crucial aspect of the NX-2420. It offers a range of connectivity options, including USB, Ethernet, and Bluetooth, enabling seamless integration with existing systems and wireless printing from mobile devices. This flexibility is particularly beneficial for businesses that utilize point-of-sale (POS) systems and want to enhance their overall operational efficiency.

Another notable characteristic of the NX-2420 is its durability. Built to withstand the rigors of a busy environment, this printer features a robust casing and is designed to handle high-volume printing tasks. Furthermore, it operates quietly, contributing to a more pleasant working atmosphere for staff and customers alike.

In addition to standard printing capabilities, the NX-2420 is also equipped with advanced features such as an integrated cutter for precise label cutting and an optional built-in camera that enhances functionality in specific applications. This adaptability makes the NX-2420 suitable for a wide range of scenarios, from retail checkout counters to inventory management systems.

In conclusion, the Star Micronics NX-2420 is an exceptional thermal printer that combines speed, durability, and versatility. With its array of features and technologies, it stands out as a reliable choice for businesses looking to enhance their printing solutions and improve operational efficiency. Whether for creating receipts, labels, or tickets, the NX-2420 is poised to meet the demands of today's dynamic business environment.
Top Page Image Contents