Star Micronics NX-2420 user manual Define download characters

Page 84

DOWNLOAD CHARACTER COMMANDS

Define download characters

Mode

ASCII

 

 

 

Decimal

 

 

Hexadecimal

 

 

<ESC>

“8~” <O>

nl

27

38

0 nl

16

26

00 nl

 

Std.

n2

m0

ml

m2

n2

m0

ml

m2

n2

m0

ml

m2

 

 

dl

d2

 

dx

dl d2

.. . dx

 

dl

d2 .

dx

Defines one or more new characters and stores them in RAM for later use. EDS switch A-2 must be OFF; otherwise RAM is used as

an input buffer, not downloading characters, and this command is - ignored.

nZ is the character code of the first character defined and n2 is the character code of the last character defined. nZ must be equal to or less than n2.

The data for each character start with three bytes specifying propor- tional spacing attributes: the first byte, m0, specifies the left of the character; the second byte, ml, specifies the character width; the third byte, m2, specifies the right of the character. These values must not exceed the following maximum limits:

-

Next comes the dot data. Normal character height is 24 dots, so there must be 3 x ml bytes of dot data. If the printer is in super/subscript mode, however, the character height is 16 dots, so there must be 2 x ml bytes of dot data.

Each data byte indicates eight vertical dots, with the most signifi- cant bit being the top dot, and the least significant bit being the bottom dot.

For further details, please refer to chapter 5.

76

Page 83 Page 85
Image 84
Page 83 Page 85
Contents NX-2420 Above statement applies only IOprinkrs marketed in the USA HOW to USE this Manual Page Features of the Printer Table of Contents Default Settings Specifications Chapter Checking the carton contents Den tifying printer parts Printer’s external partsInstalling the ribbon cartridge and the roller unit Mounting the platen knobFigum 1-4. Removing the top cover Page Hgure 1-7. Install the roller unit onto the printer Slide the cartridge into the slot with the power switch off Ins falling the optional cartridgeConnecting the printer to your computer Connecting the interface cableAutomatic loading Loading Single SheetsFigure I-17. Loading a single sheet Manual loading Loading and Parking Fanfold Forms Loading the paper from the rear of the printerPage 75.Mounting the paper guide for fanfold forms Loading the paper from the bottom of the printer Figure l-16.Pull up the tractor unit for bottom feedingPaper parking Paper unparking Loading MULTI-PART Forms Adjusting the Printing GAP Paper Type Weight Memo Control Panel Operations On Line button Paper Feed buttonSET/EJECT/PARK button Pitch buttonFont button Short test mode POWER-UP FunctionsLong test mode Print area test mode Stay in Panel PitchStay in Panel Font Stay in Panel Pitch and FontHexadecimal dump Lprint CHR$I NextOUT &H3BC,I OUT &H3BE,S OUT &H3BE,J Return Form feed Top of formForward micro-feed Reverse micro-feedChanging the auto loading value Clearing the buffer/All reset Selecting the print color Store Macro DefinitionPage Default Settings Functions of the EDS SElTlNGS Page 1OCPIDRAFT 1OCPIHS Draft OFF 17CPIDRAFT Page LoFFloFFloml Bidirectional TEST/ADJUSTMENT Mode Raft On LNE Printer Control Commands Select draft quality characters Select draft pica charactersSelect draft elite characters Select draft condensed charactersSelect Characters Select LQ pica charactersSelect LQ elite characters Select LQ condensed CharactersSelect LQ proportional Characters Select LQ fontSelect font Cancel emphasized printing Select italic CharactersSelect upright characters Emphasized printingCancel double-s trike printing Start underliningStop underlining Starf VerliningSelect score Select ornament characterSuperscript Cancel superscript or subscript SubscriptSelect standard character set Select IBM character setSelect character Set #I Select character set #2Select international character set Enable printing of all character codes Enable printing of all character codes on next characterSelect IBM code Select slash zero Select normal zeroPica pitch Elite pitchCancel condensed printing Cancel expanded printingSemi-condensed Condensed printingCancel one-line expanded printing Expanded printing for one lineSelect character width Select proportional spacingSelect master print mode Select fixed spacingIncrease character spacing Select double or quadruple size Select character sizePrint double-height characters Return to normal height Select character height, width, and line spacingSet line spacing to l/8 inch Set line spacing to 7160or 7/72 inchSet line spacing to l/6 inch Set line spacing to n/360 inchSet base unit for line spacing Set line spacing to n/180 inch or n/216 inchSet line spacing to n/60 inch or n/72 inch Select forward feed mode Select reverse feed modeExecute ES Line feedPerform one n/l804nch or n/216=inch line feed Perform one n/180-inch reverse line feedFeed paper n lines Set top of page at current positionCancel bottom margin Set page length to n inchesSet bottom margin Disable paper-out detector Enable paper-out detectorReturn to top of current Set vertical tab stopsSet vertical tab stops every n lines Set vertical tab stops in channelSelect vertical tab channel Vertical tabSet left margin Set right marginCancel automa tic line feed Set left and right marginsCarriage return Set automatic line feedLeft justify Center textRight justify Full justifyReset all tab stops Set horizontal tab stopsSet horizontal tab stops every n columns Horizontal TabRelative horizontal Tab Relative horizontal tab in inchesAbsolute horizontal tab in inches Absolute horizontal tab in columnsPrint normal-density g-bit graphics Print double-density g-bit graphicsPrint double-density, double-speed g-bit graphics Print quadruple-density g-bit graphicsSe/ect graphics mode Print hex-density 24-bit graphicsSeiecf graphics mode Convert graphics DensityDefine download characters ?n4 Copy character set from ROM into RAM Select download character setShift download character area Select draft pica download character set Select draft elite download character setSelect draft condensed download characters Select LQ pica download charactersSelect L Q elite download characters Select LQ condensed download charactersSelect LQ proportional download characters Select ROM character setSelect print color Set MSB toCancel last line Accept MSB as isDelete last character sent Set printer off-lineStop printing BellBidirectional printing Unidirectional printingReset printer Manual feedAuto feed Eject paper from ASF

NX-2420 specifications

The Star Micronics NX-2420 is a leading-edge thermal printer designed to meet the diverse demands of modern businesses. Renowned for its compact design and robust build, the NX-2420 excels in performance and versatility, making it an ideal choice for retail, hospitality, and various other industries.

One of the standout features of the NX-2420 is its high-speed printing capability. With a print speed of up to 200 millimeters per second, it ensures that transactions are completed promptly, delivering receipts and labels without delay. This efficiency helps businesses provide superior customer service, especially during peak hours.

The NX-2420 supports multiple paper widths, accommodating various label and receipt sizes. This flexibility allows businesses to tailor their printing solutions to fit specific needs, whether they require larger labels for shipping or smaller receipts for purchases. The printer also utilizes direct thermal printing technology, eliminating the need for ink or toner. This not only reduces ongoing operational costs but also minimizes maintenance efforts, making it a user-friendly option.

Connectivity is a crucial aspect of the NX-2420. It offers a range of connectivity options, including USB, Ethernet, and Bluetooth, enabling seamless integration with existing systems and wireless printing from mobile devices. This flexibility is particularly beneficial for businesses that utilize point-of-sale (POS) systems and want to enhance their overall operational efficiency.

Another notable characteristic of the NX-2420 is its durability. Built to withstand the rigors of a busy environment, this printer features a robust casing and is designed to handle high-volume printing tasks. Furthermore, it operates quietly, contributing to a more pleasant working atmosphere for staff and customers alike.

In addition to standard printing capabilities, the NX-2420 is also equipped with advanced features such as an integrated cutter for precise label cutting and an optional built-in camera that enhances functionality in specific applications. This adaptability makes the NX-2420 suitable for a wide range of scenarios, from retail checkout counters to inventory management systems.

In conclusion, the Star Micronics NX-2420 is an exceptional thermal printer that combines speed, durability, and versatility. With its array of features and technologies, it stands out as a reliable choice for businesses looking to enhance their printing solutions and improve operational efficiency. Whether for creating receipts, labels, or tickets, the NX-2420 is poised to meet the demands of today's dynamic business environment.
Top Page Image Contents