Star Micronics NX-2410 user manual Perform one n/780-inch or n/276-inch line feed

Page 79

Perform one n/780-inch or n/276-inch line feed

Mode	ASCII			Decimal		Hexadecimal
Both	<ESC>	“J”	n	27 74	n	1B4A	n

Feeds the paper once by n/180 inches (Standard mode) or n/216 inches (IBM mode), where n is between 0 and 255. Does not move the print position right or left when DIP switch 1-2 is OFF; returns the carriage

to the left margin if DIP switch 1-2 is ON. Does not change the

line-spacing setting.

Perform one n/180-inch reverse line feed

Mode	ASCII			Decimal		Hexadecimal		I
	< ESC >		n					I
Std.	< ESC >	“j”	n	21 106	n	IlB 6A	n	I
								I

Feeds the paper once by n/180 inches in the reverse direction, where n is between 0 and 255. Does not move the print position right or left when DIP switch 1-2 is OFF; returns the carriage to the left margin if DIP switch 1-2 is ON. Does not change the line-spacing setting. Ignored when friction feed is used.

Feed paper n lines

Mode

ASCII

Decimal

Hexadecimal

Both

<ESC>

“f’

“I”

n

27

102

49

n

IB

66

31

n

<ESC>

“f

<I>

n

27

102

1

n

1B

66

01

n

Feeds the paper n lines from the current line, where n is between 0 and iii.

Set top of page at current position

1Mode 1	ASCII		I	Decimal	1	Hexadecimal	1
I
IBM	<ESC>	“4”	27	52		1B 34	I
							I
	Sets the	current position	as the top-of-page		position.	Note that this	can

also be done from the control panel.

Set page length to n lines

Mode	ASCII			Decimal		Hexadecimal
Both	<ESC>	“C”	n	21 67	n	IB 43	n

Sets the page length ton lines in the current line spacing, where n is between 1 and 127 in Standard mode or between 1 and 255 in IBM mode. Changing the line spacing later does not alter the physical page length. The current line becomes the top of the page.

Image 79

Contents MULTI-FONT Relocate the computerorprinterwithrespectto the mceiver HOW to USE this Manual Features of the Printer Quad-sized Tableofcontents Commercial Software Download Character Generator Chapter Check the carton contentsPage Remove the top cower Setting UPInstall the ribbon cartridge Lnsfall the optional IC card Replace the top coverConnect the printer to the computer Connect the printer’s power cordMount the paper guide Figure i-7. Mounting the paper guide for single sheets Semiautomatic loadingManual loading Opening the rear cover Loading and Parking Fanfold FormsClamp Lever Figure l-72. Mounting the paper guide for fanfold forms Paper parkingTest Printing Interface test Long self testAdjusting the Printing GAP IBM Page Selected Mode You OFF Chapter Switches and IndicatorsPaper feed switch On Line switchQuiet Mode switch Short test pattern On Line switch POWER-UP FunctionsLprint CHR$I Next Return Switch combination functions of control panel Switch Combination FunctionsPage Page Memo Printer menu Installing Your SoftwareType styles Printer command optionsWidth Alignment Setting the DIP SwitchesUsing Your Software Initialization sequenceType style and pitch selection Other printer commandsCan help you to use ESC4italicESC5 print Memo HARD-COPYING the Screen MS-DOS and PC-DOS With DOS and BasicAprint README.DOC Programming the Printer with DOS CommandsNew file Acopy CON LQPRINT.BAT Programming the Printer with BasicLprint Lprint END How the program works Page Lprint ES= c~$oc~$6oc~$6o RkPLACING the Ribbon Cleaning the PrinterReplacing the ribbon cartridge Replacing the Print HeadReplacing the print head ScrewsReplacing the battery Replacing the Battery in the RAM CardIf a// text is printed on the same line If the printer doesn’t printIf fanfold paper becomes stuck If label paper becomes stuckIf you have problems with graphics If you have problems with horizontal tabulationIf you have problems with download characters Interface and Emu/a tion Switches and indicatorsCharacter Sets Dot Matrix SizeDimensions and Weight Paper SpecificationsType Sty/es and Pitches Option Electrical SpecificationsFnterface Signals Environmental RequirementsKCK OUT Memo FdNT Control Commands Select draft quality characters Printer Control CommandsSelect italic characters Select LQ charactersSelect LQ type style Select ornament characterEmphasized printing Cancel emphasized printingCancel double-strike printing Select Upright CharactersStart Overlining Stop UnderliningCharacter SET Commands Select Normal Zero Enable printing of all character codesEnable printing of a// character codes on next character Select Slash ZeroHigh-density Elite Pitch Pica PitchElite pitch High-speed elite pitchExpanded printing Cancel condensed printingCancel Expanded Printing CondensedSelect fixed spacing Select Master Print modeCaocel one-line expanded printing Select proportional spacingReturn To normal Increase character SpacingSelect double or quadruple size Print Double-height CharactersWidth Select CharacterSelect character height, width, and line spacing Set line spacing to 7160 or 7172 inch Vertical Position CommandsSelect character type and print pitch Set line spacing to 718 inchSet line spacing to n/360 inch Set line spacing to 116 inchSet base unit for line spacing Set line spacing to n/180 or n/276 inchLine feed Select forward feed modeDefine line spacing to n/72 inch Execute ESC aPerform one n/780-inch or n/276-inch line feed Form feed Cancel top and bottom marginsSet page Iength to n inches Set bottom marginSet vertical tab stops every n lines Disable paper-out detectorEnable paper-out detector Set vertical tab stopsTab Horizontal Position CommandsSet left margin Select vertical tab channelSet Cancel autoniatic line feedSet left and right margins Carriage returnRight justify BackspaceLeft justify Center textHorizontal tab ResetSet horizontal tab stops Set horizontal tab stop every n columnsAbsolute horizontal tab in co/umns Relative horizontal TabRelative horizontal tab in inches Absolute horizontal tab in inchesPrint Bit quadruple-density Graphics Print 8-bit Sing/e-density GraphicsPrint 8-bit double-density Graphics Print 8-bit double-density, double-speed graphicsPrint 24bit hex-density graphics Select graphics modeCopy character set from ROM into RAM card Select Graphics ModeDownload Character Commands Convert graphics DensitySelect download character set Define DownloadSet MS8 to Other Printer Control CommandsSelect ROM character Set MS6 toQuiet print Cancel last lineCancel Quiet print Repeat dataStop printing Cancel immediate PrintSet printer off-line Set printer on-heManual feed BidirectionalUnidirectional printing One-line unidirectional printingEject paper From ASF Reset PrinterSet print start position on ASF Memo Normal character AppendixcDOWNLOADDraft characters Pica Super/subscript character 1220 Then QUA=2 Else QUA=0 CLS Locate PX,PY Print ISO$ Plot chara,-.ter ------------~-~----~-~-~~~~-~~~~~ Character Sets Standardcharacterset IuIX Ih Y I-G- I-G- l-7 Page IBM Character SET #l I‘?Additional Character SET International Character Sets # $ h o 0 §Index Irl 107 Command Summary 109 Select base unit for line spacing 111