Star Micronics NX-2410 Set left and right margins, Carriage return, Cancel autoniatic line feed

Page 83

Sets the right margin at column n in the current character pitch (pica

pitch if proportional spacing is currently selected). Column n becomes the last character position in the line. The right margin does not move if the character pitch is changed later. The right margin must be within the limits below:

Pica		4snn80
Elite		5sns96
Semi-condensed		6	sn		5	120
Condensed	pica	7	5	n	5	137
Condensed	elite	8	5	n	6	160

Expanded	pica		2snj40
Expanded	elite		3snn448
Expanded	semi-condensed		3sns60
Expanded	condensed	pica	4sns68
Expanded	condensed	elite	4jnj80

Set left and right margins

Mode	ASCII				Decimal		Hexadecimal
Both I	<ESC>	“X”	nl	n2	I27 88 nl n2	IlB	58 nl n2

Sets the left margin at column nl and the right margin at column n2.

See the preceding commands for margin restrictions and other notes.

Carriage return

Mode	ASCII	Decimal	Hexadecimal
Both I	<CR>	I 13	1 OD

Prints the current line and returns the next print position to the left margin. If DIP switch l-8 is ON, also performs a line feed.

Set	automatic	line	feed
Mdde	ASCII			Decimal	Hexadecimal
IBM	<ESC>	” 5”	<I>	21 53 1	1B 35 01

Causes the printer to perform both a carriage return and line feed each time it receives a < CR > code. This command takes priority over DIP switch 1-8.

Cancel autoniatic line feed

Mode	ASCII		Decimal		Hexadecimal
IBM I	<ESC>	“ 5” co>	127 53	0	1 IB 35 00

Causes the printer to perform only a carriage return when it receives a < CR > code. This command takes priority over DIP switch l-8.

Image 83

Contents MULTI-FONT Relocate the computerorprinterwithrespectto the mceiver HOW to USE this Manual Features of the Printer Quad-sized Tableofcontents Commercial Software Download Character Generator Chapter Check the carton contentsPage Remove the top cower Setting UPInstall the ribbon cartridge Lnsfall the optional IC card Replace the top coverMount the paper guide Connect the printer’s power cordConnect the printer to the computer Figure i-7. Mounting the paper guide for single sheets Semiautomatic loadingManual loading Opening the rear cover Loading and Parking Fanfold FormsClamp Lever Figure l-72. Mounting the paper guide for fanfold forms Paper parkingTest Printing Interface test Long self testAdjusting the Printing GAP IBM Page Selected Mode You OFF Chapter Switches and IndicatorsPaper feed switch On Line switchQuiet Mode switch Short test pattern On Line switch POWER-UP FunctionsLprint CHR$I Next Return Switch combination functions of control panel Switch Combination FunctionsPage Page Memo Printer menu Installing Your SoftwareWidth Printer command optionsType styles Alignment Setting the DIP SwitchesUsing Your Software Initialization sequenceType style and pitch selection Other printer commandsCan help you to use ESC4italicESC5 print Memo HARD-COPYING the Screen MS-DOS and PC-DOS With DOS and BasicAprint README.DOC Programming the Printer with DOS CommandsNew file Acopy CON LQPRINT.BAT Programming the Printer with BasicLprint Lprint END How the program works Page Lprint ES= c~$oc~$6oc~$6o RkPLACING the Ribbon Cleaning the PrinterReplacing the ribbon cartridge Replacing the Print HeadReplacing the print head ScrewsReplacing the battery Replacing the Battery in the RAM CardIf a// text is printed on the same line If the printer doesn’t printIf fanfold paper becomes stuck If label paper becomes stuckIf you have problems with download characters If you have problems with horizontal tabulationIf you have problems with graphics Interface and Emu/a tion Switches and indicatorsCharacter Sets Dot Matrix SizeType Sty/es and Pitches Paper SpecificationsDimensions and Weight Option Electrical SpecificationsFnterface Signals Environmental RequirementsKCK OUT Memo FdNT Control Commands Select draft quality characters Printer Control CommandsSelect italic characters Select LQ charactersSelect LQ type style Select ornament characterEmphasized printing Cancel emphasized printingCancel double-strike printing Select Upright CharactersStart Overlining Stop UnderliningCharacter SET Commands Select Normal Zero Enable printing of all character codesEnable printing of a// character codes on next character Select Slash ZeroHigh-density Elite Pitch Pica PitchElite pitch High-speed elite pitchExpanded printing Cancel condensed printingCancel Expanded Printing CondensedSelect fixed spacing Select Master Print modeCaocel one-line expanded printing Select proportional spacingReturn To normal Increase character SpacingSelect double or quadruple size Print Double-height CharactersSelect character height, width, and line spacing Select CharacterWidth Set line spacing to 7160 or 7172 inch Vertical Position CommandsSelect character type and print pitch Set line spacing to 718 inchSet line spacing to n/360 inch Set line spacing to 116 inchSet base unit for line spacing Set line spacing to n/180 or n/276 inchLine feed Select forward feed modeDefine line spacing to n/72 inch Execute ESC aPerform one n/780-inch or n/276-inch line feed Form feed Cancel top and bottom marginsSet page Iength to n inches Set bottom marginSet vertical tab stops every n lines Disable paper-out detectorEnable paper-out detector Set vertical tab stopsTab Horizontal Position CommandsSet left margin Select vertical tab channelSet Cancel autoniatic line feedSet left and right margins Carriage returnRight justify BackspaceLeft justify Center textHorizontal tab ResetSet horizontal tab stops Set horizontal tab stop every n columnsAbsolute horizontal tab in co/umns Relative horizontal TabRelative horizontal tab in inches Absolute horizontal tab in inchesPrint Bit quadruple-density Graphics Print 8-bit Sing/e-density GraphicsPrint 8-bit double-density Graphics Print 8-bit double-density, double-speed graphicsPrint 24bit hex-density graphics Select graphics modeCopy character set from ROM into RAM card Select Graphics ModeDownload Character Commands Convert graphics DensitySelect download character set Define DownloadSet MS8 to Other Printer Control CommandsSelect ROM character Set MS6 toQuiet print Cancel last lineCancel Quiet print Repeat dataStop printing Cancel immediate PrintSet printer off-line Set printer on-heManual feed BidirectionalUnidirectional printing One-line unidirectional printingSet print start position on ASF Reset PrinterEject paper From ASF Memo Normal character AppendixcDOWNLOADDraft characters Pica Super/subscript character 1220 Then QUA=2 Else QUA=0 CLS Locate PX,PY Print ISO$ Plot chara,-.ter ------------~-~----~-~-~~~~-~~~~~ Character Sets Standardcharacterset IuIX Ih Y I-G- I-G- l-7 Page IBM Character SET #l I‘?Additional Character SET International Character Sets # $ h o 0 §Index Irl 107 Command Summary 109 Select base unit for line spacing 111