Star Micronics 800C user manual Bescheinigung des Importeurs, Trademark Acknowledgments

Page 2

Federal Communications Commission Radio Frequency Interference Statement

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of FCC rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communica- tions. However, there is no guarantee that interference will not occur in a particular installation. If this equip- ment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures.

•Reorient or relocate the receiving antenna.

•Increase the separation between the equipment and receiver.

•Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

•Consult the dealer or an experienced radio/TV technician for help.

Note: The following cable must be used to comply with FCC Regulations as well as to avoid interference to home equipment.

Interface cable: Twisted-pair shielded cable Non-shielded A.C. Power Cord

Do not attempt to modify this equipment. If modified, your authority to operate this equipment might be voided by the FCC.

The above statement applies only to printers marketed in the U.S.A.

Statement of The Canadian Department of Communications Radio InterferenceRegulations

This digital device does not exceed the Class B limits for radio noise emissions from digital apparatus set out in the Radio Interference Regulations of the Canadian Department of Communications.

Le présent appareil numérique n'emen pas de bruits radioélectriques dépassant les limits applicable aux appareils numériques de la classe B prescrites dan le Règlement sur le brouillage radioélectrique édicté par le minisère des Communications du Canada.

The above statement applies only to printers marketed in Canada.

Bescheinigung des Importeurs

Hiermit wird bescheinigt, daß der

COMPUTER DRUCKER TM300

in Übereinstimmung mit den Bestimmungen der

VDE 0878 3/22.89, EN 55022: 1987, BMPT Vfg. 243/1991 und 46/1992 funk-entstört ist.

Dem Bundesamt für Zulassungen in der Telekommunikation wurde das Inverkehrbringen dieses Gerätes angezeigt und die Berechtigung zur Überprüfung der Serie auf die Einhaltung der Bestimmungen eingeräumt.

Star Micronics Deutschland, GmbH Westerbachstraße 59, D-60489 Frankfurt, Germany

The above statements apply only to printers marketed in Germany.

Trademark Acknowledgments

TrueType: Apple Computer, Inc.

Windows 3.1, MS-DOS: Microsoft Corporation

Notice

•All rights reserved. Reproduction of any part of this manual in any form whatsoever without STAR's express permission is forbidden.

•The contents of this manual are subject to change without notice.

All efforts have been made to ensure the accuracy of the contents of this manual at the time of press. However, should any errors be detected, STAR would greatly appreciate being informed of them.

• The above notwithstanding, STAR can assume no responsibility for any errors in this manual.

©Copyright 1994 Star Micronics Co., Ltd.

Page 1 Page 3
Image 2
Page 1 Page 3
Contents WinType 800C Bescheinigung des Importeurs Trademark AcknowledgmentsContents Maintenance & troubleshooting SpecificationsIntroduction Reference information How to use this manualFeatures of the printer GlossaryPaper tray base Printer componentsPaper tray Paper tray coverTop cover Bobbin sockets Vii Setting up your printer Unpacking and checking the package contentsDescription Model Number Size Sheets/Pack DescriptionModel Number Yield Per Roll Placing the printer Preparing to printLoading paper StepsGrooves for the bobbin Page Page Steps Power OFF Page Installing the printer driver and TrueType fonts Installing the printer driver and TrueType fontsPage Custom Install Without Install Font TrueType font samplesPrinting with WinType 800C Control panelMedia Type Dimensions Recommended Type Recommended print mediaOperating the printer Loading print mediaReplace the paper tray cover Printable area Printable Area Getting ready to print Page DIP switch settings Changing halftones and image quality Changing halftonesError High speed printing Click on Fast Print to Port Click on Use Max. MemoryFilm Roll Paper Size Monochrome Color Other buttons in the Options dialog box Intensity Steps Click on the Drop-down list box to reveal media sizes Replacing the film roll Do not touch this sensorPage Changing the film roll setting Page Printing with iron-on transfer Steps for transferring the image on the cloth Steps for the finishing process Page Maintenance & troubleshooting Maintaining your printerDampen a soft cloth with ethanol Page Wipe the paper feeders with the soft cloth Make sure that Ready lamp is lit Clearing paper jams Per eject. Proceed to onPage Transporting your printer Inside of the printer Remove the paper tray cover and the paper tray base Troubleshooting Region of problem DescriptionOverall print is light Check Possible remedy Printed image has vertical linesCheck Possible remedy Color variations are too large Patterns appear where print density is highOverall print is dark Check Possible remedy Two sheets of paper are fed at the same time Only part of the image is printed Check Possible remedyPaper jams occur frequently Check Possible remedy Other DIP switch settings Print Type Items that can be changed with the DIP switchesPinout of interface connector Specifications Reference informationMemory Power supplyPrinter supply accessories InterfacePrinter supply options Glossary Error Diffusion CommandConfiguration DefaultHandshaking Gamma CorrectionHalftone Hex dumpTitle bar PortraitPostScript TrueType fontSymbols IndexLPT1 RAM Customer service information Customer response
Top Page Image Contents