IBM 9179-MHB, 9117-MMB manual Select Commit Follow any instructions that are shown

Page 84

b.Select Commit.

c.Follow any instructions that are shown.

d.If a Do you want to review the previously displayed error? message is shown, select Yes and press Enter.

e.If an SRN is shown, suspect a loose card or connection. If no obvious problem is shown, record the SRN and contact your service provider for assistance..

f.If no SRN is shown, go to 5.

5.Test the part by doing the following:

a.At the command line, type diagmenu and press Enter.

b.From the Function Selection menu, select Advanced Diagnostics Routines and press Enter.

c.From the Diagnostic Mode Selection menu, select System Verification and press Enter.

d.Select All Resources, or select the diagnostics for the individual part to test only the part you replaced, and any devices that are attached to the part you replaced and press Enter.

Did the Resource Repair Action menu appear? No: Go to step 6.

Yes: Go to step 7.

6.Did the Testing Complete, No trouble was found message appear?

v No: There is still a problem. Contact your service provider. This ends the procedure.

v Yes: Select Log Repair Action, if not previously logged, from the Task Selection menu to update the AIX error log. If the repair action was reseating a cable or adapter, select the resource associated with that repair action. If the resource associated with your action is not displayed on the Resource List, select sysplanar0 and press Enter.

Tip: This action changes the indicator light for the part from the fault state to the normal state. Go to step 9 on page 73

7.Select the resource for the replaced part from the Resource Repair Action menu. When a test is run on a resource in system verification mode, and that resource has an entry in the AIX error log, if the test on the resource was successful, the Resource Repair Action menu appears. Complete the following steps to update the AIX error log to indicate that a system-detectable part has been replaced.

Note: On systems with a indicator light for the failing part, this changes the indicator light to the normal state.

a.Select the resource that has been replaced from the Resource Repair Action menu. If the repair action was reseating a cable or adapter, select the resource associated with that repair action. If the resource associated with your action does not appear on the Resource List, select sysplanar0. Press Enter.

b.Select Commit after you make your selections. Did another Resource Repair Action display appear?

No: If the No Trouble Found display appears, go to step 9 on page 73

Yes: Go to step 8.

8.Select the parent or child of the resource for the replaced part from the Resource Repair Action menu if necessary. When a test is run on a resource in system verification mode, and that resource has an entry in the AIX error log, if the test on the resource was successful, the Resource Repair Action menu appears. Complete the following steps to update the AIX error log to indicate that a system-detectable part has been replaced.

Note: This changes the indicator light for the part from the fault state to the normal state.

72Power Systems: Power supplies for the 9117-MMB or 9179-MHB

Page 83 Page 85
Image 84
Page 83 Page 85
Contents Power supplies for the 9117-MMB or 9179-MHB Page Power supplies for the 9117-MMB or 9179-MHB Copyright IBM Corporation 2010 Contents Iv Power Systems Power supplies for the 9117-MMB or 9179-MHB World Trade safety information German safety informationLaser safety information Laser complianceVi Power Systems Power supplies for the 9117-MMB or 9179-MHB Safety notices Page L003 Power Systems Power supplies for the 9117-MMB or 9179-MHB Whats new in Power supplies MarchRemoving the power supply Related information Before you begin Identifying a failing part Connect the power cable a to the power supply Close the rear rack door Replacing the power supply Power supply LEDs Power supplies FRU fault and identify LED Removing a power supply Fan fault LED and fan identify button Related information Power Systems Power supplies for the 9117-MMB or 9179-MHB Removing a power supply Removing a power supply fan Power supplies Replacing a fan Connecting the power cable to the front of an expansion unit Expansion unit ac power and OCA power LEDs Related information Replacing a fan Replacing a power supply Expansion unit ac power and OCA power LEDs Related information Power Systems Power supplies for the 9117-MMB or 9179-MHB Removing an input power distribution assembly cover Related information Replacing an input power distribution assembly Connecting the power cables at the rear of an expansion unit Replacing an input power distribution assembly Replacing an input power distribution assembly cover Common procedures for installable features Before you beginPower Systems Power supplies for the 9117-MMB or 9179-MHB Power supplies Identifying a part Control panel LEDsControl panel Select Display Previous Diagnostic Results and press Enter Activating the indicator light for the failing partDeactivating the failing-part indicator light Related conceptsActivating the failing-part indicator light Related information Identifying a part by using the Virtual I/O Server Starting the system or logical partition Starting a system that is not managed by an HMC or an SdmcPower supplies Stopping a system or logical partition Stopping a system that is not managed by an HMC or an SdmcStopping a system by using the Hardware Management Console From the Actions menu, select Operations → Power Off Placing the system in the service position Placing the system into the operating position Removing and replacing covers for the 8202-E4B or 8205-E6B Removing the front cover Removing the front cover Removing the front cover Installing the front cover Removing the service access cover Installing the outside service access cover Installing the service access cover Installing the inside service access cover Installing the outside service access cover Removing the power cords for a rack-mounted system Tasks area expand Serviceability → Hardware → MES Tasks Connecting the power cordsVerifying the installed part Did the Resource Repair Action menu appear? No Go to step No. This ends the procedure Sign on with at least service level authority Verifying an installed part by using stand-alone diagnostics Choose Commit Exit to the command line Activating and deactivating LEDs by using the HMC Click Close EventViewing serviceable events by using the HMC Select Manage Serviceable EventsSelect Actions → View Comments Deactivating a system attention LED or partition LED Activating or deactivating identify LED by using the Sdmc Select Actions → System Status and Health → Event LogPower supplies Select Commit Follow any instructions that are shown Verifying a repair Load the operating systemDid you encounter any problems? Verifying the repair in AIXPerform the following steps Did another Resource Repair Action 801015 display? Yes Power supplies Procedure Verifying the repair in Linux Verifying the repair from the management consoleClosing a service call View Serviceable Event DetailsPower supplies Yes Go to step No Continue with the next step Select the No FRU Replaced for this Serviceable Event option Power Systems Power supplies for the 9117-MMB or 9179-MHB Closing a service call using AIX or Linux System hardware is functioning correctly Select the Diagnostics Routines option Power Systems Power supplies for the 9117-MMB or 9179-MHB Power supplies Yes Continue with the next step No Go to step Click Close Event Is the error class recorded in on page 91? Activating and deactivating LEDs Open Operations Open LED Status Click Actions Service and Support Hardware Identify LED Click Save settings Copyright IBM Corp Trademarks Electronic emission noticesClass a Notices Ethernet connection usage restrictionIndustry Canada Compliance Statement Avis de conformité à la réglementation dIndustrie CanadaEuropean Community Compliance Statement Vcci Statement JapanElectromagnetic Interference EMI Statement Taiwan IBM Taiwan Contact InformationPage Class B Notices Electromagnetic Interference EMI Statement RussiaIndustry Canada Compliance Statement Power Systems Power supplies for the 9117-MMB or 9179-MHB Terms and conditions Power Systems Power supplies for the 9117-MMB or 9179-MHB
Top Page Image Contents