Fujitsu 600C manual Paper Specifications, Paper Size, Paper conditions, 2.1 ADF

Page 19

3.5 Paper Specifications

This section provides the readable paper specifications for the automatic document feeder (ADF).

3.5.1Paper Size

A

Feeding direction

B

Maximum		Minimum
A	B	A	B
216	356	100	100

Unit: mm

Figure 3-4 Paper size specifications

3.5.2Paper conditions

3.5.2.1ADF

a)Paper quality Wood-free paper

PPC paper; Specified by XEROX Corporation

b)Paper specifications

Legal size, 14~28 lbs

3-7

Image 19

Contents Version Page Table of Contents Diagnostics Group 3 error flowchart no paper in ADF paper tray Page General GeneralSystem Block Diagram Outer View Device ConfigurationComponents Functional Specifications Remarks Functional SpecificationsEnvironmental Specifications Remarks Environmental SpecificationsRemoving the Shipping Bracket OperationRemove the shipping retainer Fasten the shipping retainer Indication Panel Power On/OffName Color Function Setting the Scsi ID and Connecting the Interface CableNames and functions of the indicators Scsi ID settingScsi Cable Connection Position 2.1 ADF Paper SpecificationsPaper Size Paper conditionsItems to avoid FIatbedADF readable area Readable areaWhen the document size is of letter/A4 size or smaller Document Setting MethodFlatbed Setting the ADF paper chute When the document is a thick book2 ADF Placing the document on the ADF paper chute Placing the documents on the ADF paper chuteSeparating the sheets for easy feeding Angling the document sheetsCleaning the document cover and the document glass CleaningCleaning inside the ADF Page Interface ∙ Busy ∙ Check Condition ∙ Good ∙ Reservation Conflict Connection Physical SpecificationsTermination Physical SpecificationSpecifications 1SCSI physical specificationsPin assignments Signal Name Pin NumberAddresses of Scsi devices System configurationSystem configuration Scsi Bus2Bus signals Bus signals3Bus phases vs. signal drive sources 1/2 Bus signal drive conditionsMethod of driving the interface signal Bus PhasesOr connection Nonor connection 5Signal delay times definition Time Definition Signal delay times definition BUS Free phaseTime Definition Arbitration phase BSY Scsi SEL Selection phase Information Transfer phase type Phase Information Transfer phasesDB7 to 9,P Transfer Direction Asynchronous transfer from target to initiator Asynchronous information transferAsynchronous transler from initiator to target Relative addressing is not supported CommandsControl byte is not supported Bit and field described as Reserved are Reserve Unit commandCommands Operation Command Code hex DescriptionTP third party Byte Reserve Unit command Command phase initiator Õ targetTpid third party device ID Byte Release Unit command Command phase initiator → target Release Unit commandTP third party Byte Step Bus phase Initiator operation Target operation Inquiry commandInquiry command Command phase initiator → target 10 Inquiry commandCode Byte Evpd enable vital product data ByteCAllocation length Byte Aenc Inquiry data Data in phase target → initiatorISO version, Ecma version, Ansi approved version Byte SftRst Soft Reset ByteADF mode Byte 24, bit Color mode Byte 24, bit 6 toRequest Sense command Command phase initiator → target Request Sense command11 Request Sense command Valid Byte Sense data Data EN phase target → initiatorError code Byte Allocation length ByteSense key Byte ILI incorrect length indicator ByteFM file mark Byte EOM end of medium ByteSense code Send Diagnostic commandCommand-specific information bytes Bytes 8 to B Sense Additional DescriptionPF page format Byte Send Diagnostic command Command phase initiator → targetSlftst selftest Byte Contents of self-test Test Unit Ready commandResults of self-test Acknowledgment Test Unit Ready command Command phase initiator → targetSET Window command Command phase initiator → target SET Window commandTransfer Length Bytes 6 to Window date Data OUT phase initiator → targetHeader Window descriptor block Upper left X,YULX, ULY Bytes 6 to 9, a to D Y resolution XR, YR Bytes 2 to 3 and 4 toWindow identifier Byte Auto ByteRemarks Brightness ByteHalftone pattern Bytes lB to 1C lB reserved Bit per pixel Byte 1ARIF reverse image format Byte 1D, bit Bit ordering Bytes 1E to 1F18 Vender unique parameters byte 28 and later Update of ScanPartner 600C OEM manual7.4 B&W Scanning Vender unique parameters Compression type, argument Bytes 20 toPage Source Byte 2A, Bit Color Scanning Vender unique parameters19 Vendor unique parameters byte 28 and later ADF Byte 2A, BitLine count Byte 2F to Highlight value Byte 2BShadow value Byte 2C Line width Byte 2D to 2EObject Position command Position type Byte Object Position command Command phase initator → targetBit Normal Unload objectLoad object Count Bytes 2 toStep Bus phase Initiator operation Target operation Read commandADF sequence Transfer length TL Bytes 6 to Read command Command phase initiator → targetData type code Byte Data type qualifier Bytes 4 toPixel size data Data Type Code = Data in phase target → initiatorImage data Data Type Code = For binary dataScan Command phase initiator → target Scan commandCode Status of unit Status Status phase target initiatorMessages Phase ATN detection timingATN detection Message types Command Complete X00 Message in phase target → initiatorMessage Message Reject X07 Message IN/OUT phase initiator → target Abort X06 Message OUT phase initiator → targetATN detection phase Action Message rejected Action No Operation X08 Message OUT phase initiator → targetBUS Device Reset X0C Message OUT phase initiator → target Phase when ATN is detected ActionIdendify X80 to XFF Message OUT phase initiator → target Initial sequence Command SequenceSingle Read Read command sequenceRead sequence for B&W mode Read sequenceMultiple Read Status Transition of Logical Unit Sense key Error TableItems for Specifying Window Page Ready LED Paper Jam LED Error indication Online diagnosticsOnline diagnostics Offline diagnostics results Offline diagnosticsGroup 1 error flowchart Lamp assembly Diagnostic flowchartsGroup 2 error flowchart Flatbed/ADF motor Group 3 error flowchart paper in ADF paper tray Group 3 error flowchart no paper in ADF paper tray