Fujitsu 600C manual Idendify X80 to XFF Message OUT phase initiator → target

Page 83

This scanner generates the UNIT ATTENTION condition to all initiators.

After being initialized, the initiators move to the BUS FREE phase.

The initiators do not intend to issue another message by activating ATN before they deactivate the ACK of the BUS DEVICE RESET message.

4.6.2.8IDENDIFY (X'80' TO X'FF'): MESSAGE OUT phase (initiator → target)

This message specifies either a logical unit under control of the target, or a process incorporated in the target (maintenance, self-diagnostic, etc.).

7

6

5

4

3

2

1

0

1

Specifies a logical unit number (for bit 5 = 0)

Specifies a process incorporated in the target (for bit 5 = 1)

(Reserved)

(Reserved)

1. Processed by the target alone

0.Processed by the target and logical unit

1.The initiator does not permit disconnect

0.The initiator permits disconnect Bit for distinguishing from other messages

This scanner does not support the target-incorporated process function. Therefore, if a 1 is set in bit 5, the IDENTIFY message is rejected with the MESSAGE REJECT message.

4-55

Image 83

Contents Version Page Table of Contents Diagnostics Group 3 error flowchart no paper in ADF paper tray Page General GeneralSystem Block Diagram Outer View Device ConfigurationComponents Functional Specifications Remarks Functional SpecificationsEnvironmental Specifications Remarks Environmental SpecificationsRemoving the Shipping Bracket OperationRemove the shipping retainer Fasten the shipping retainer Indication Panel Power On/OffName Color Function Setting the Scsi ID and Connecting the Interface CableNames and functions of the indicators Scsi ID settingScsi Cable Connection Position 2.1 ADF Paper SpecificationsPaper Size Paper conditionsItems to avoid FIatbedADF readable area Readable areaFlatbed Document Setting MethodWhen the document size is of letter/A4 size or smaller 2 ADF When the document is a thick bookSetting the ADF paper chute Placing the document on the ADF paper chute Placing the documents on the ADF paper chuteSeparating the sheets for easy feeding Angling the document sheetsCleaning the document cover and the document glass CleaningCleaning inside the ADF Page Interface ∙ Busy ∙ Check Condition ∙ Good ∙ Reservation Conflict Connection Physical SpecificationsTermination Physical SpecificationSpecifications 1SCSI physical specificationsPin assignments Signal Name Pin NumberAddresses of Scsi devices System configurationSystem configuration Scsi Bus2Bus signals Bus signals3Bus phases vs. signal drive sources 1/2 Bus signal drive conditionsOr connection Nonor connection Bus PhasesMethod of driving the interface signal 5Signal delay times definition Time Definition Time Definition BUS Free phaseSignal delay times definition Arbitration phase BSY Scsi SEL Selection phase DB7 to 9,P Transfer Direction Information Transfer phasesInformation Transfer phase type Phase Asynchronous transfer from target to initiator Asynchronous information transferAsynchronous transler from initiator to target Control byte is not supported CommandsRelative addressing is not supported Bit and field described as Reserved are Reserve Unit commandCommands Operation Command Code hex DescriptionTpid third party device ID Byte Reserve Unit command Command phase initiator Õ targetTP third party Byte TP third party Byte Release Unit commandRelease Unit command Command phase initiator → target Step Bus phase Initiator operation Target operation Inquiry commandInquiry command Command phase initiator → target 10 Inquiry commandCAllocation length Byte Evpd enable vital product data ByteCode Byte Aenc Inquiry data Data in phase target → initiatorISO version, Ecma version, Ansi approved version Byte SftRst Soft Reset ByteADF mode Byte 24, bit Color mode Byte 24, bit 6 to11 Request Sense command Request Sense commandRequest Sense command Command phase initiator → target Valid Byte Sense data Data EN phase target → initiatorError code Byte Allocation length ByteSense key Byte ILI incorrect length indicator ByteFM file mark Byte EOM end of medium ByteSense code Send Diagnostic commandCommand-specific information bytes Bytes 8 to B Sense Additional DescriptionSlftst selftest Byte Send Diagnostic command Command phase initiator → targetPF page format Byte Results of self-test Test Unit Ready commandContents of self-test Acknowledgment Test Unit Ready command Command phase initiator → targetSET Window command Command phase initiator → target SET Window commandHeader Window date Data OUT phase initiator → targetTransfer Length Bytes 6 to Window descriptor block Upper left X,YULX, ULY Bytes 6 to 9, a to D Y resolution XR, YR Bytes 2 to 3 and 4 toWindow identifier Byte Auto ByteRemarks Brightness ByteHalftone pattern Bytes lB to 1C lB reserved Bit per pixel Byte 1ARIF reverse image format Byte 1D, bit Bit ordering Bytes 1E to 1F18 Vender unique parameters byte 28 and later Update of ScanPartner 600C OEM manual7.4 B&W Scanning Vender unique parameters Compression type, argument Bytes 20 toPage Source Byte 2A, Bit Color Scanning Vender unique parameters19 Vendor unique parameters byte 28 and later ADF Byte 2A, BitLine count Byte 2F to Highlight value Byte 2BShadow value Byte 2C Line width Byte 2D to 2EObject Position command Bit Object Position command Command phase initator → targetPosition type Byte Normal Unload objectLoad object Count Bytes 2 toADF sequence Read commandStep Bus phase Initiator operation Target operation Transfer length TL Bytes 6 to Read command Command phase initiator → targetData type code Byte Data type qualifier Bytes 4 toPixel size data Data Type Code = Data in phase target → initiatorImage data Data Type Code = For binary dataScan Command phase initiator → target Scan commandCode Status of unit Status Status phase target initiatorATN detection Phase ATN detection timingMessages Message Command Complete X00 Message in phase target → initiatorMessage types ATN detection phase Action Abort X06 Message OUT phase initiator → targetMessage Reject X07 Message IN/OUT phase initiator → target Message rejected Action No Operation X08 Message OUT phase initiator → targetBUS Device Reset X0C Message OUT phase initiator → target Phase when ATN is detected ActionIdendify X80 to XFF Message OUT phase initiator → target Initial sequence Command SequenceSingle Read Read command sequenceRead sequence for B&W mode Read sequenceMultiple Read Status Transition of Logical Unit Sense key Error TableItems for Specifying Window Page Online diagnostics Online diagnosticsReady LED Paper Jam LED Error indication Offline diagnostics results Offline diagnosticsGroup 2 error flowchart Flatbed/ADF motor Diagnostic flowchartsGroup 1 error flowchart Lamp assembly Group 3 error flowchart paper in ADF paper tray Group 3 error flowchart no paper in ADF paper tray