IBM 37L1388 manual Setting the configuration jumper

Page 19

Some non-IBM computers

support

the

cable-select setting, where the

position of

the device on the cable determines

whether

a

device is

master

or slave. See the

documentation

that

comes

with

your

computer

to

determine

if your

system

supports

this

setting.

 

 

 

 

 

 

Step 4. Setting the configuration jumper

The

illustration

above

shows

 

the

master

1

setting,

the

slave2

 

setting,

and

 

the

 

cable-select

 

 

3

setting. Configure

the

CD-ROM

 

drive

by

placing

a

jumper

over

the

 

 

set

of

pins

corresponding

to

the

 

setting

you

 

chose

in

“Step

3.

 

Selecting

an

 

IDE

port”.

 

If

 

you

 

are

configuring

the CD-ROM drive

as

 

master,

set

the

jumper

to

the

master

 

 

 

1

 

device

setting.

(This

is

 

how

the

 

drive

is

set

when

it

is

shipped.)

If there is a

 

second

device

on

the

IDE

port,

make

sure

 

that

device

is

configured

as

slave.

 

 

 

If

 

you

 

are

configuring

the

CD-ROM

drive

as

 

slave,

set

the

jumper

to

the

 

slave

 

 

 

2

 

device

setting.

Make

sure

that

the

 

other

device

on

the

 

IDE

port

is

configured

 

as

master

(or master-with-slave-present).

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

If

 

you

 

are

configuring

the

CD-ROM

drive

as

 

cable-select,

set

the

jumper

to

the

 

 

 

cable-select

3

 

device

setting.

If

there

is

another

device

on

the

IDE

port,

make

 

sure

that

the

second

device

 

is

also

configured

for

cable-select.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Step

 

5.

Mounting

the

drive

 

in

 

the

bay

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Attention:

 

Be sure

to

use

the

M3

x

5

 

mm

mounting

screws

in

the

option

 

 

 

package.

Using

screws

that

are

 

too

 

long

might

damage

 

the

drive.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

You

can

mount the CD-ROM

drive

horizontally

or

vertically

in

the

computer. If

you

 

 

 

mount

the

drive

vertically,

you

must

secure

any

 

CDs

you

place

into

the

drive

before

 

the drive tray is closed,

or

the

CD-ROM

drive

will

 

not

be

able

 

to

read the

CD

 

properly.

For

further

instructions

on

securing

your

 

CDs

in

a

vertically

mounted

drive,

 

 

go to

page

2-2.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

1.

Slide the drive into

the

bay.

 

Your

computer

might

have

specific

required

 

 

 

 

 

procedures

 

for

installing

storage

devices.

Refer

to

the documentation

 

that

comes

 

 

 

 

with

your

computer

for

further

instructions.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Part 1: Installation guide

1-13

Image 19
Contents 40X-17X Internal IDE CD-ROM Drive 1999 Contents Iv 40X-17X Internal IDE CD-ROM Drive Part Vi 40X-17X Internal IDE CD-ROM Drive Description Instructions Before you begin40X-17X Internal IDE CD-ROM Drive Back view of the drive View DrivePort IDE connectorStep Bay Setting the configuration jumperAttaching the cables to the drive Faceplates StepDriver For System SettingsDriver For ExitSecond Drive That Uses Integrated Drive Electronics IDE orStandard Speed10 40X-17X Internal IDE CD-ROM Drive View Drive Connects the dc power cord to the CD-ROM drive DC power connectorConnects the CD-ROM drive to the IDE cable Setting the configuration jumper 14 40X-17X Internal IDE CD-ROM Drive Step 16 40X-17X Internal IDE CD-ROM Drive Information WarrantyRegistration 18 40X-17X Internal IDE CD-ROM Drive Cause Loss Data With Care Kept Clean To insure That TheyCare Life Your CDs WipingLoading a CD ForCaring Looks Press the Eject/Load buttonIllustrations Tray YourPlayer Windows 95 or WindowsStart DeviceDisc AccessoriesOS/2 Warp Windows NTWindows DataWindows System You Have NotDone Insert Data Icon Displayed40X-17X Internal IDE CD-ROM Drive DOS with Windows 3.x, Windows DriverAppendixes CustomizingIRQ US English default, does not need to be specifiedDevice Driver Use the following options to configure the device driverEight Must be identical to the deviceWith no To access the CD-ROM drive. For example, you might useWill Set This Value to Value forBelow Where Device drivers and programs are LocatedUtility disables Cache SoftwareDevice manager driver Installable file system driverServer OS/2 softwareDevice Problem descriptions Icon Windows 3.X does Not Display YouDisk TypeErratically 12 40X-17X Internal IDE CD-ROM Drive Read Fit HelpEnter Web site, the PSG Electronic ProblemSection Contains Life YourPuerto Appendix WarrantyRico PartItems Default Services mustAll Features Analysis ServiceStates Part 20 40X-17X Internal IDE CD-ROM Drive Items Not Covered by WarrantyThose Cases Safe AccessOwn Fulfil their22 40X-17X Internal IDE CD-ROM Drive For That ItalySpain Those24 40X-17X Internal IDE CD-ROM Drive Trademarks 26 40X-17X Internal IDE CD-ROM Drive EmissionFitting States RelatingNot Accept Satisfy28 40X-17X Internal IDE CD-ROM Drive Page IBM