Cisco Systems MEM-S3-1GB= manual Ejector lever Captive installation screw, 78-15538-02, 91525

Page 10

Opening the Ejector Levers (Horizontal Chassis Shown)

Installing the SP and RP Memory Upgrade Kit

Figure 1

Opening the Ejector Levers (Horizontal Chassis Shown)

1

2

3

4

5

WS-X6348-RJ-45V

6

48 PORT
10/100 BASE-T	ETHERNET SWITCHING
	MODULE

o		o
		o
INPUT	FAN	OUTPUT
OK	OK	FAIL

INPUT	FAN	OUTPUT
OK	OK	FAIL

91525

Ejector lever

Captive installation screw

Supervisor Engine 720 Switch Processor and Route Processor Memory Installation Note

10	78-15538-02

Image 10

Contents Product Number MEM-S2-512MB=, MEM-MSFC2-512MB=, MEM-S3-1GB= ContentsMEM-MSFC3-1GB= Safety Overview Warnung WICHTIGE SICHERHEITSHINWEISE Varning! VIKTIGA SÄKERHETSANVISNINGAR Este símbolo de aviso significa perigo. Você se encontra em uma situação em que há risco de lesões corporais. Antes de trabalhar com qualquer equipamento, esteja ciente dos riscos que envolvem os circuitos elétricos e familiarize-se com as práticas padrão de prevenção de acidentes. Use o número da declaração fornecido ao final de cada aviso para localizar sua tradução nos avisos de segurança traduzidos que acompanham o dispositivo Safety Overview 78-15538-02Safety Overview Required Tools Installing the SP and RP Memory Upgrade KitRemoving the Supervisor Engine Horizontal slots Vertical slotsOpening the Ejector Levers Horizontal Chassis Shown Ejector lever Captive installation screw91525 Removing and Installing the DRAM DIMMs Removing the Module from the Chassis Horizontal Chassis ShownHandling a DIMM DRAM DIMM Location on the Supervisor EngineDRAM DIMM 28580To install the DRAM DIMM upgrade kit, perform these steps Installing the Supervisor Engine Insert module WS-SUP72 SUPERVISOR 720 WITH INTEGRATED SWITCH FABRICFigure 6 Positioning the Module in a Horizontal Slot Chassis between slot guidesf. Verify that the STATUS LED is lit Clearing the EMI Gasket in a Horizontal Slot Chassis Press down1mm Gap between the module EMI gasket and the module above it 91528Positioning the Module in a Vertical Slot Chassis Insert module between slot guidesGap between the module EMI gasket and the module above it 1mm Press left Press leftTranslated Safety Warnings Statement 1029-Blank Faceplates and Cover PanelsWarnung Blanke Faceplates und Abdeckungen haben drei wichtigen Funktionen 1 Sie schützen vor gefährlichen Spannungen und Strom innerhalb des Chassis 2 sie halten elektromagnetische Interferenzen EMI zurück, die andere Geräte stören könnten 3 sie lenken den kühlenden Luftstrom durch das Chassis. Das System darf nur betrieben werden, wenn alle Karten, Faceplates, Voder- und Rückabdeckungen an Ort und Stelle sind Advarsel Blanke frontplader og sidepaneler tjener tre vigtige formål de forhinder udsættelse for farlig spænding og strøm inde i chassiset, de isolerer elektromagnetisk interferens EMI, der kan forstyre andet udstyr, og de leder en strøm af kølig luft gennem chassiset. Betjen ikke systemet medmindre alle kort, frontplader, sidepaneler og bagpaneler er på plads Statement 1030-Equipment Installation Advarsel Bare opplært og kvalifisert personell skal foreta installasjoner, utskiftninger eller service på dette utstyret Statement 1034-Backplane Voltage Aviso O sistema em funcionamento emite tensão ou energia elétrica perigosa no painel traseiro. Seja cauteloso ao fazer a manutenção Product Documentation DVD Obtaining DocumentationCisco.com Ordering DocumentationDocumentation Feedback Reporting Security Problems in Cisco ProductsCisco Product Security Overview Obtaining Technical Assistance Cisco Technical Support & Documentation WebsiteSubmitting a Service Request Definitions of Service Request SeverityObtaining Additional Publications and Information 2003-2005 Cisco Systems, Inc. All rights reserved