Cisco Systems MEM-S2-512MB= manual To install the DRAM DIMM upgrade kit, perform these steps

Page 13

To install the DRAM DIMM upgrade kit, perform these steps:

Installing the SP and RP Memory Upgrade Kit

To install the DRAM DIMM upgrade kit, perform these steps:

Step 1 Remove the old DRAM DIMM from its socket by pulling the locking spring clips on both sides outward and tilting the DIMM free of the clips. Be careful not to break the clips on the DIMM connector.

Step 2 Holding the DIMM by its edges, gently lift to disconnect it from the DIMM socket, and place the DIMM on an antistatic mat or foam.

Step 3 Remove the upgrade DIMM from the antistatic package.

Step 4 Hold the DIMM between your thumbs and forefingers, with the connector edge (the metal fingers) down, and insert the connector edge of the DIMM into the socket connector.

Note A notch (key) is located on the right connector edge of the DIMM. (See Figure 5.) This notch key ensures that the DIMM is correctly oriented in the socket.

Step 5 Slide the DIMM into the connector so that none of the metal fingers at the edge of the DIMM are visible under the lining of the connector.

Caution When inserting the DIMM, use firm but not excessive pressure. If you damage a socket, you must return the supervisor engine to Cisco for repair.

Step 6 Press down on the edges of the DIMM until the DIMM clicks into place. (See Figure 5.)

Figure 5

Installing the DIMM in the Socket

28736

Supervisor Engine 720 Switch Processor and Route Processor Memory Installation Note

	78-15538-02	13

Image 13

Contents Product Number MEM-S2-512MB=, MEM-MSFC2-512MB=, MEM-S3-1GB= ContentsMEM-MSFC3-1GB= Safety Overview Warnung WICHTIGE SICHERHEITSHINWEISE Varning! VIKTIGA SÄKERHETSANVISNINGAR Este símbolo de aviso significa perigo. Você se encontra em uma situação em que há risco de lesões corporais. Antes de trabalhar com qualquer equipamento, esteja ciente dos riscos que envolvem os circuitos elétricos e familiarize-se com as práticas padrão de prevenção de acidentes. Use o número da declaração fornecido ao final de cada aviso para localizar sua tradução nos avisos de segurança traduzidos que acompanham o dispositivo 78-15538-02 Safety Overview78-15538-02 Required Tools Installing the SP and RP Memory Upgrade KitRemoving the Supervisor Engine Vertical slots Horizontal slotsOpening the Ejector Levers Horizontal Chassis Shown Ejector lever Captive installation screw91525 Removing the Module from the Chassis Horizontal Chassis Shown Removing and Installing the DRAM DIMMsDRAM DIMM DRAM DIMM Location on the Supervisor EngineHandling a DIMM 28580To install the DRAM DIMM upgrade kit, perform these steps Installing the Supervisor Engine Figure 6 Positioning the Module in a Horizontal Slot Chassis WS-SUP72 SUPERVISOR 720 WITH INTEGRATED SWITCH FABRICInsert module between slot guidesf. Verify that the STATUS LED is lit 1mm Gap between the module EMI gasket and the module above it Press downClearing the EMI Gasket in a Horizontal Slot Chassis 91528Insert module between slot guides Positioning the Module in a Vertical Slot ChassisPress left Press left Gap between the module EMI gasket and the module above it 1mmStatement 1029-Blank Faceplates and Cover Panels Translated Safety WarningsWarnung Blanke Faceplates und Abdeckungen haben drei wichtigen Funktionen 1 Sie schützen vor gefährlichen Spannungen und Strom innerhalb des Chassis 2 sie halten elektromagnetische Interferenzen EMI zurück, die andere Geräte stören könnten 3 sie lenken den kühlenden Luftstrom durch das Chassis. Das System darf nur betrieben werden, wenn alle Karten, Faceplates, Voder- und Rückabdeckungen an Ort und Stelle sind Advarsel Blanke frontplader og sidepaneler tjener tre vigtige formål de forhinder udsættelse for farlig spænding og strøm inde i chassiset, de isolerer elektromagnetisk interferens EMI, der kan forstyre andet udstyr, og de leder en strøm af kølig luft gennem chassiset. Betjen ikke systemet medmindre alle kort, frontplader, sidepaneler og bagpaneler er på plads Statement 1030-Equipment Installation Advarsel Bare opplært og kvalifisert personell skal foreta installasjoner, utskiftninger eller service på dette utstyret Statement 1034-Backplane Voltage Aviso O sistema em funcionamento emite tensão ou energia elétrica perigosa no painel traseiro. Seja cauteloso ao fazer a manutenção Cisco.com Obtaining DocumentationProduct Documentation DVD Ordering DocumentationDocumentation Feedback Reporting Security Problems in Cisco ProductsCisco Product Security Overview Cisco Technical Support & Documentation Website Obtaining Technical AssistanceDefinitions of Service Request Severity Submitting a Service RequestObtaining Additional Publications and Information 2003-2005 Cisco Systems, Inc. All rights reserved