Cisco Systems MEM-MSFC2-512MB=, MEM-S2-512MB=, MEM-S3-1GB= f. Verify that the STATUS LED is lit

Page 16

f.Verify that the STATUS LED is lit.

Installing the SP and RP Memory Upgrade Kit

Step 3 Depending on the orientation of the slots in the chassis (horizontal or vertical), perform one of the following two sets of stepsfor positioning the module in a chassis with either horizontal or vertical slots:

Horizontal slots

a.Position the supervisor engine in the slot. (See Figure 6.) Make sure that you align the sides of the module carrier with the slot guides on each side of the slot.

b.Carefully slide the supervisor engine into the slot until the EMI gasket along the top edge of the module makes contact with the module in the slot above it and both ejector levers have closed to approximately 45 degrees with respect to the module faceplate. (See Figure 7.)

c.Using the thumb and forefinger of each hand, grasp the two ejector levers, and press down to create a small 0.040 inch (1 mm) gap between the supervisor engine’s EMI gasket and the module above it. (See Figure 7.)

Note Do not press down too forcefully on the levers because they will bend and become damaged.

d.While pressing down, simultaneously close the left and right ejector levers to fully seat the supervisor engine in the backplane connector. The ejector levers are fully closed when they are flush with the module faceplate. (See Figure 7.)

Note Failure to fully seat the module in the backplane connector can result in error messages.

e.Tighten the two captive installation screws on the supervisor engine.

Note Make sure that the ejector levers are fully closed before tightening the captive installation screws.

f.Verify that the STATUS LED is lit.

Periodically check the STATUS LED. If the STATUS LED changes from orange to green, the module has successfully completed the boot process and is now online.

If the STATUS LED remains orange or turns red, the module has not successfully completed the boot process and may have encountered an error.

Supervisor Engine 720 Switch Processor and Route Processor Memory Installation Note

16	78-15538-02

Image 16

Contents Product Number MEM-S2-512MB=, MEM-MSFC2-512MB=, MEM-S3-1GB= ContentsMEM-MSFC3-1GB= Safety Overview Warnung WICHTIGE SICHERHEITSHINWEISE Varning! VIKTIGA SÄKERHETSANVISNINGAR Este símbolo de aviso significa perigo. Você se encontra em uma situação em que há risco de lesões corporais. Antes de trabalhar com qualquer equipamento, esteja ciente dos riscos que envolvem os circuitos elétricos e familiarize-se com as práticas padrão de prevenção de acidentes. Use o número da declaração fornecido ao final de cada aviso para localizar sua tradução nos avisos de segurança traduzidos que acompanham o dispositivo Safety Overview 78-15538-02Safety Overview Required Tools Installing the SP and RP Memory Upgrade KitRemoving the Supervisor Engine Horizontal slots Vertical slotsOpening the Ejector Levers Horizontal Chassis Shown Ejector lever Captive installation screw91525 Removing and Installing the DRAM DIMMs Removing the Module from the Chassis Horizontal Chassis ShownDRAM DIMM Location on the Supervisor Engine DRAM DIMMHandling a DIMM 28580To install the DRAM DIMM upgrade kit, perform these steps Installing the Supervisor Engine WS-SUP72 SUPERVISOR 720 WITH INTEGRATED SWITCH FABRIC Figure 6 Positioning the Module in a Horizontal Slot ChassisInsert module between slot guidesf. Verify that the STATUS LED is lit Press down 1mm Gap between the module EMI gasket and the module above itClearing the EMI Gasket in a Horizontal Slot Chassis 91528Positioning the Module in a Vertical Slot Chassis Insert module between slot guidesGap between the module EMI gasket and the module above it 1mm Press left Press leftTranslated Safety Warnings Statement 1029-Blank Faceplates and Cover PanelsWarnung Blanke Faceplates und Abdeckungen haben drei wichtigen Funktionen 1 Sie schützen vor gefährlichen Spannungen und Strom innerhalb des Chassis 2 sie halten elektromagnetische Interferenzen EMI zurück, die andere Geräte stören könnten 3 sie lenken den kühlenden Luftstrom durch das Chassis. Das System darf nur betrieben werden, wenn alle Karten, Faceplates, Voder- und Rückabdeckungen an Ort und Stelle sind Advarsel Blanke frontplader og sidepaneler tjener tre vigtige formål de forhinder udsættelse for farlig spænding og strøm inde i chassiset, de isolerer elektromagnetisk interferens EMI, der kan forstyre andet udstyr, og de leder en strøm af kølig luft gennem chassiset. Betjen ikke systemet medmindre alle kort, frontplader, sidepaneler og bagpaneler er på plads Statement 1030-Equipment Installation Advarsel Bare opplært og kvalifisert personell skal foreta installasjoner, utskiftninger eller service på dette utstyret Statement 1034-Backplane Voltage Aviso O sistema em funcionamento emite tensão ou energia elétrica perigosa no painel traseiro. Seja cauteloso ao fazer a manutenção Obtaining Documentation Cisco.comProduct Documentation DVD Ordering DocumentationDocumentation Feedback Reporting Security Problems in Cisco ProductsCisco Product Security Overview Obtaining Technical Assistance Cisco Technical Support & Documentation WebsiteSubmitting a Service Request Definitions of Service Request SeverityObtaining Additional Publications and Information 2003-2005 Cisco Systems, Inc. All rights reserved