Cisco Systems MEM-MSFC2-512MB= manual Documentation Feedback, Cisco Product Security Overview

Page 28
Documentation Feedback

Documentation Feedback

Documentation Feedback

You can rate and provide feedback about Cisco technical documents by completing the online feedback form that appears with the technical documents on Cisco.com.

You can send comments about Cisco documentation to bug-doc@cisco.com.

You can submit comments by using the response card (if present) behind the front cover of your document or by writing to the following address:

Cisco Systems

Attn: Customer Document Ordering

170 West Tasman Drive

San Jose, CA 95134-9883

We appreciate your comments.

Cisco Product Security Overview

Cisco provides a free online Security Vulnerability Policy portal at this URL:

http://www.cisco.com/en/US/products/products_security_vulnerability_policy.html

From this site, you can perform these tasks:

Report security vulnerabilities in Cisco products.

Obtain assistance with security incidents that involve Cisco products.

Register to receive security information from Cisco.

A current list of security advisories and notices for Cisco products is available at this URL:

http://www.cisco.com/go/psirt

If you prefer to see advisories and notices as they are updated in real time, you can access a Product Security Incident Response Team Really Simple Syndication (PSIRT RSS) feed from this URL:

http://www.cisco.com/en/US/products/products_psirt_rss_feed.html

Reporting Security Problems in Cisco Products

Cisco is committed to delivering secure products. We test our products internally before we release them, and we strive to correct all vulnerabilities quickly. If you think that you might have identified a vulnerability in a Cisco product, contact PSIRT:

Emergencies — security-alert@cisco.com

An emergency is either a condition in which a system is under active attack or a condition for which a severe and urgent security vulnerability should be reported. All other conditions are considered nonemergencies.

Nonemergencies — psirt@cisco.com

In an emergency, you can also reach PSIRT by telephone:

1 877 228-7302

1 408 525-6532

Supervisor Engine 720 Switch Processor and Route Processor Memory Installation Note

28

78-15538-02

 

 

Image 28
Contents Product Number MEM-S2-512MB=, MEM-MSFC2-512MB=, MEM-S3-1GB= ContentsMEM-MSFC3-1GB= Safety Overview Warnung WICHTIGE SICHERHEITSHINWEISE Varning! VIKTIGA SÄKERHETSANVISNINGAR Este símbolo de aviso significa perigo. Você se encontra em uma situação em que há risco de lesões corporais. Antes de trabalhar com qualquer equipamento, esteja ciente dos riscos que envolvem os circuitos elétricos e familiarize-se com as práticas padrão de prevenção de acidentes. Use o número da declaração fornecido ao final de cada aviso para localizar sua tradução nos avisos de segurança traduzidos que acompanham o dispositivo Safety Overview 78-15538-02Safety Overview Required Tools Installing the SP and RP Memory Upgrade KitRemoving the Supervisor Engine Horizontal slots Vertical slotsOpening the Ejector Levers Horizontal Chassis Shown Ejector lever Captive installation screw91525 Removing and Installing the DRAM DIMMs Removing the Module from the Chassis Horizontal Chassis ShownDRAM DIMM Location on the Supervisor Engine DRAM DIMMHandling a DIMM 28580To install the DRAM DIMM upgrade kit, perform these steps Installing the Supervisor Engine WS-SUP72 SUPERVISOR 720 WITH INTEGRATED SWITCH FABRIC Figure 6 Positioning the Module in a Horizontal Slot ChassisInsert module between slot guidesf. Verify that the STATUS LED is lit Press down 1mm Gap between the module EMI gasket and the module above itClearing the EMI Gasket in a Horizontal Slot Chassis 91528Positioning the Module in a Vertical Slot Chassis Insert module between slot guidesGap between the module EMI gasket and the module above it 1mm Press left Press leftTranslated Safety Warnings Statement 1029-Blank Faceplates and Cover PanelsWarnung Blanke Faceplates und Abdeckungen haben drei wichtigen Funktionen 1 Sie schützen vor gefährlichen Spannungen und Strom innerhalb des Chassis 2 sie halten elektromagnetische Interferenzen EMI zurück, die andere Geräte stören könnten 3 sie lenken den kühlenden Luftstrom durch das Chassis. Das System darf nur betrieben werden, wenn alle Karten, Faceplates, Voder- und Rückabdeckungen an Ort und Stelle sind Advarsel Blanke frontplader og sidepaneler tjener tre vigtige formål de forhinder udsættelse for farlig spænding og strøm inde i chassiset, de isolerer elektromagnetisk interferens EMI, der kan forstyre andet udstyr, og de leder en strøm af kølig luft gennem chassiset. Betjen ikke systemet medmindre alle kort, frontplader, sidepaneler og bagpaneler er på plads Statement 1030-Equipment Installation Advarsel Bare opplært og kvalifisert personell skal foreta installasjoner, utskiftninger eller service på dette utstyret Statement 1034-Backplane Voltage Aviso O sistema em funcionamento emite tensão ou energia elétrica perigosa no painel traseiro. Seja cauteloso ao fazer a manutenção Obtaining Documentation Cisco.comProduct Documentation DVD Ordering DocumentationDocumentation Feedback Reporting Security Problems in Cisco ProductsCisco Product Security Overview Obtaining Technical Assistance Cisco Technical Support & Documentation WebsiteSubmitting a Service Request Definitions of Service Request SeverityObtaining Additional Publications and Information 2003-2005 Cisco Systems, Inc. All rights reserved