Cisco Systems 9124E manual Installation and safety considerations, Installing the Switch

Page 18

Table 5 Cisco MDS 9124e Fabric Switch components

Item

Description

2Dust covers for empty SFP ports

3Cisco MDS 9124e Fabric Switch for HP c-Class BladeSystem installation guide

Installation and safety considerations

The Cisco MDS 9124e Fabric Switch installs in the I/O bays in the rear of the HP c-Class BladeSystem enclosure. Refer to the HP BladeSystem c7000 Enclosure setup and installation guide for specific enclosure requirements.

Installing multiple switches

Install and configure one Cisco MDS 9124e Fabric Switch at a time. Each switch must be assigned a unique Ethernet IP address during configuration. Once the IP address on the Cisco MDS 9124e Fabric Switch has been set, you may install additional switches in the enclosure. See the HP BladeSystem c7000 Enclosure setup and installation guide for help identifying your specific enclosure setup, available connections and power requirements.

Electrical considerations

The Cisco MDS 9124e Fabric Switch requires 55 watts, provided by the enclosure. No other power requirement or provision exists.

Environmental considerations

Ensure proper cooling and ventilation by verifying the following:

The air vents on the enclosure are not blocked or restricted.

The ambient air temperature at the front of the enclosure does not exceed 35°C (95°F) while the switch is operating.

IMPORTANT:

The dust covers that ship with your Cisco MDS 9124e Fabric Switch must be inserted into any ports where SFPs are not installed, to help contain air flow in the BladeSystem chassis.

Installing the Switch

CAUTION:

Do not install multiple switches at the same time with default addresses or an address conflict will occur. See ”Setting the IP address” for more information.

The Cisco MDS 9124e Fabric Switch is a hot-pluggable device. The enclosure power may be on or off when inserting the switch. Follow these steps to install the switch:

18 Set Up

Image 18
Contents Cisco MDS 9124e Fabric Switch for HP c-Class BladeSystem Legal and notice information Contents Switch technical specifications Managing the SwitchRegulatory compliance and safety Electrostatic dischargeGlossary Contents Related documentation About this guideIntended audience Contacting HP Technical SupportDocument conventions and symbols Document conventions Convention ElementSubscription service Other HP web sitesAbout This Guide Switch features OverviewComponent identification Port side of the Switch Switch redundancyInternal ports summary Switch licensing PortChannelOptional hardware kits Optional hardwareOverview Setup Shipping carton contentsInstalling multiple switches Installation and safety considerationsInstalling the Switch Electrical considerationsScale 2/3 = OA power verification Indicators Setting the IP addressPower-on LEDs Checking LEDsResetting the IP Address OA connect interconnectConfiguring the Switch Items Required for ConfigurationConnecting to the Command Line Interface Setting the date and time Verifying Installed LicensesModifying the FC domain ID optional On Demand PortsDisabling and enabling a port Recovering the Admin Password Verifying the configurationBacking up the configuration Switchboot# dir bootflash Set Up Managing the Switch Management featuresMaintaining the Switch Installing dust covers in empty portsReplacing an SFP transceiver Replacing the Switch Installing an SFP SFP componentsPowering on and off LED indicators Front panel LED indicators during normal operationInterpreting LED activity Post and boot specifications LED patternsPort link status LED patterns LED color Boot Interpreting Post resultsManaging the Switch Modifications Regulatory compliance and safetyRegulatory compliance CablesRegulatory compliance identification numbers Laser safety warningLaser device Certification and classification informationEuropean Union notice International notices and statementsCanadian notice avis Canadien Class a equipmentBsmi notice Japanese notice Korean notices Safety Battery replacement noticeTaiwan battery recycling notice English notice Japanese power cord statementWaste Electrical and Electronic Equipment directive Dutch noticeCzechoslovakian notice Estonian notice Finnish noticeFrench notice German noticeGreek notice Hungarian notice Italian notice Latvian noticeLithuanian notice Polish notice Portuguese noticeSlovakian notice Slovenian notice Spanish notice Swedish notice Regulatory compliance and safety How to prevent electrostatic discharge Electrostatic dischargeGrounding methods Electrostatic discharge Switch technical specifications General specificationsGeneral specifications Specification Weight and physical dimensions Switch physical dimensions DimensionSupported HBAs Environmental requirementsSupported SFPs Environmental requirements ConditionSwitch technical specifications Glossary Error Directory serviceEnabled zone FCS switchFLPort Fibre ChannelFill word FrameLatency Link servicesLPort LinkNon-participating SwitchNode ModeSwitch port Service rateSingle mode Request rateCharacter TopologyTransmission Trap SnmpGlossary Index Index Cisco MDS 9124e Fabric Switch for HP c-Class BladeSystem Index