Cisco Systems 9124E manual Resetting the IP Address, OA connect interconnect

Page 22

• In a UNIX environment, type: tip /dev/ttyb –9600

5.Log into the OA.

6.Identify the interconnect bay number where the switch is installed.

7.Type the following at the command line:

OA> connect interconnect x

Where x is the interconnect bay number where the switch is installed.

If you are using the switch for the first time, the switch setup utility starts automatically. If this is not the first time the switch has been used, enter the setup command at the system prompt.

8.Enter a password for the system administrator. (There is no default password.)

NOTE:

Be sure to use a strong password. You must explicitly configure a password that meets the requirements listed in the “Configuring User Accounts” section in the Cisco MDS 9000 Family CLI Configuration Guide.

9.Follow the instructions in the switch setup utility to configure the IP address, the netmask, and other parameters for the switch.

NOTE:

Refer to the Cisco MDS 9000 Family CLI Configuration Guide for complete information about the switch setup utility.

10.When you have finished with the switch setup utility, logout and disconnect the serial cable.

Resetting the IP Address

Use the following steps to reset the IP address:

1.Log in to the CLI.

2.Type config t to enter the configuration mode.

3.Type int mgmt 0.

4.Type ip address <ip><mask>.

5.Type exit.

6.Type ip default-gateway <default-gw>.

7.Type exit to exit the configuration mode.

The IP address is now reset. Type show int mgmt 0 to verify your new settings.

22 Set Up

Image 22

Contents Cisco MDS 9124e Fabric Switch for HP c-Class BladeSystem Legal and notice information Contents Switch technical specifications Managing the SwitchRegulatory compliance and safety Electrostatic dischargeGlossary Contents Related documentation About this guideIntended audience Contacting HP Technical SupportDocument conventions and symbols Document conventions Convention ElementSubscription service Other HP web sitesAbout This Guide Switch features OverviewComponent identification Switch redundancy Port side of the SwitchInternal ports summary Switch licensing PortChannelOptional hardware kits Optional hardwareOverview Setup Shipping carton contentsInstalling multiple switches Installation and safety considerationsInstalling the Switch Electrical considerationsScale 2/3 = OA power verification Indicators Setting the IP addressPower-on LEDs Checking LEDsResetting the IP Address OA connect interconnectItems Required for Configuration Configuring the SwitchConnecting to the Command Line Interface Setting the date and time Verifying Installed LicensesOn Demand Ports Modifying the FC domain ID optionalDisabling and enabling a port Verifying the configuration Recovering the Admin PasswordBacking up the configuration Switchboot# dir bootflash Set Up Managing the Switch Management featuresInstalling dust covers in empty ports Maintaining the SwitchReplacing an SFP transceiver Replacing the Switch Installing an SFP SFP componentsPowering on and off Front panel LED indicators during normal operation LED indicatorsInterpreting LED activity LED patterns Post and boot specificationsPort link status LED patterns LED color Boot Interpreting Post resultsManaging the Switch Modifications Regulatory compliance and safetyRegulatory compliance CablesRegulatory compliance identification numbers Laser safety warningLaser device Certification and classification informationEuropean Union notice International notices and statementsCanadian notice avis Canadien Class a equipmentBsmi notice Japanese notice Korean notices Battery replacement notice SafetyTaiwan battery recycling notice English notice Japanese power cord statementWaste Electrical and Electronic Equipment directive Dutch noticeCzechoslovakian notice Estonian notice Finnish noticeFrench notice German noticeGreek notice Hungarian notice Italian notice Latvian noticeLithuanian notice Polish notice Portuguese noticeSlovakian notice Slovenian notice Spanish notice Swedish notice Regulatory compliance and safety Electrostatic discharge How to prevent electrostatic dischargeGrounding methods Electrostatic discharge General specifications Switch technical specificationsGeneral specifications Specification Weight and physical dimensions Switch physical dimensions DimensionSupported HBAs Environmental requirementsSupported SFPs Environmental requirements ConditionSwitch technical specifications Glossary Error Directory serviceEnabled zone FCS switchFLPort Fibre ChannelFill word FrameLatency Link servicesLPort LinkNon-participating SwitchNode ModeSwitch port Service rateSingle mode Request rateCharacter TopologyTransmission Trap SnmpGlossary Index Index Cisco MDS 9124e Fabric Switch for HP c-Class BladeSystem Index