Cisco Systems Cisco ME 3400 manual Mounting the Switch on a Wall

Page 39

Chapter 2 Switch Installation

Installing the Switch

Mounting the Switch on a Wall

For the best support of the switch and cables, make sure the switch is attached securely to wall studs or to a firmly attached plywood mounting backboard. Mount the switch with the front panel facing up, as shown in Figure 2-11.

Warning Suitable for mounting on and over a concrete or other non-combustible surface only. Statement 345

Figure 2-11 Mounting the Switch on a Wall

1

1

1

132673

User-supplied screws

After the switch is mounted on the wall, you need to do these tasks to complete the installation:

•Power on the switch. See the “Verifying Switch Operation” section on page 2-5.

•Connect to a 10/100 port or to the RJ-45 connector of a dual-purpose port, and run the Initial Configuration Dialog. See the Cisco ME 3400 and ME 2400 Ethernet Access Switches Getting Started Guide for instructions.

•Connect to the front-panel ports. See the “Connecting to the 10/100 and 10/100/1000 Ports” section on page 2-20and the “Connecting to SFP Modules” section on page 2-21to complete the installation.

For configuration instructions about using the CLI setup program, go to Appendix D, “Configuring the Switch with the CLI-Based Setup Program.”

Cisco ME 3400 Ethernet Access Switch Hardware Installation Guide

	OL-7677-04	2-15

Image 39

Contents Americas Headquarters Page N T E N T S Installing and Removing SFP Modules Speed, Duplex, and Autonegotiation IP Settings D-2 Audience PurposeOrganization Conventions Related Publications OL-7677-04 Switch Models Setting up the SwitchFront Panel Description 1describes the switch modelsCisco ME 3400-24TS AC Ethernet Access Switch Front Panel Cisco ME 3400-24TS AC and DC Switches Front PanelCisco ME 3400G-12CS AC and DC Switches Front Panel Cisco ME 3400-24FS Switch AC Switch Front PanelSystem LED Dual-purpose ports Console port SFP module ports Cisco ME 3400G-2CS Switch Front Panel10/100 Ports Only the Cisco ME-3400-24TS Switches SFP Modules SFP Module PortsThese illustrations show the location of the System LED LEDsSFP Module Patch Cable System LEDConsole Port LEDs Power Supply LEDs Only Cisco ME 3400G-12CS SwitchesDual-Purpose Port LEDs Console PortExhaust fan Cable lock Ground connector Cisco ME 3400-24TS Switch Rear PanelCisco ME 3400-24FS Switch Rear Panel Cable lock Ground connector Fan exhaustFan exhaust AC power connector Ground connector Power Supply FeaturesCisco ME 3400G-12S Switch Rear Panel Cisco ME 3400-2CS Switch Rear PanelManagement Options Cisco ME AC Switch Power SupplyCisco ME DC Switch Power Supply Network ConfigurationsThis section covers these topics Preparing for InstallationSwitch Installation Preparing for Installation 122F 50C Statement Installation Guidelines Cisco ME 3400-24TS SwitchesCisco ME 3400G-12CS Switches This section describes these installation procedures Verifying Switch OperationInstalling the Switch Powering Off the SwitchRack-Mounting Removing Screws from the SwitchRack-Mounting Brackets Attaching Brackets to the SwitchAttaching Brackets to 19-Inch Racks 191022 Attaching Brackets for 23-Inch Racks Attaching Brackets for 24-Inch Racks Attaching Brackets for Etsi Racks Phillips machine screws Cable guide and screw Mounting the Switch in a RackAttaching the Brackets to the Switch for Wall-Mounting Wall-MountingPhillips flat-head screws 11 Mounting the Switch on a Wall Mounting the Switch on a WallTable- or Shelf-Mounting Installing and Removing SFP Modules12 SFP Module with a Bale-Clasp Latch Installing SFP ModulesBale clasp Removing SFP ModulesInserting and Removing the SFP Module Patch Cable 17 Connecting to an Ethernet Port Connecting to the 10/100 and 10/100/1000 PortsConnecting to SFP Modules Connecting to Fiber-Optic SFP ModulesLC connector 19 Connecting to a 1000BASE-T SFP Module Connecting to 1000BASE-T SFP Modules20 Connecting to a Dual-Purpose Port Connecting to Dual-Purpose PortsWhere to Go Next Diagnosing Problems Check Switch Post ResultsThis section includes these troubleshooting topics Ethernet and Fiber Cables Check Switch LEDsCheck Switch Connections Bad or Damaged CableSpanning Tree Loops SFP Module Port IssuesPort and Interface Settings Ping the End DeviceAutonegotiation and NIC Cards How to Clear the Switch IP Address and ConfigurationCheck Switch Performance Speed, Duplex, and AutonegotiationSerial Number Location on the Cisco ME 3400G-2CS Switch Locating the Switch Serial NumberSerial Number Location on the Cisco ME 3400G-2CS Switch Connector Specifications These sections describe the connectors used with the switch10/100 Ports Figure A-1 10/100 Port Pinouts Dual-Purpose Ports Figure A-2 Fiber-Optic SFP Module LC ConnectorSFP Module Cable Specifications Cable and Adapter SpecificationsTwo Twisted-Pair Cable Pinouts Four Twisted-Pair Cable Pinouts for 1000BASE-T Ports Crossover Cable and Adapter PinoutsIdentifying a Crossover Cable Adapter Pinouts TxD RxDRxD TxD Switch Console RJ-45-to-DB-25 Port DTE This appendix lists the switch technical specifications Technical SpecificationsAC Power Requirements Physical Dimensions OL-7677-04 Connecting to DC Power Grounding the Switch Preparing the Ground WireReview these safety warnings before you ground the switch Figure C-1 Stripping the Ground Wire Figure C-3 Torquing Ground-Lug Screws Torque to 15 lbf-inConnecting the Grounding Wire to Earth Ground Telco rack Grounding wireTelco rack Primary power feed Secondary redundant power feed Wiring the DC-Input Power SourceCisco ME 3400-24TS Switches Cisco ME 3400G-12CS SwitchesAll Cisco ME 3400 Switches Figure C-8 Terminal Block Plug Console Figure C-11 Inserting Wires in the Terminal Block Plug Figure C-13 Completed Wiring of Terminal Block Plug OL-7677-04 Starting the Terminal-Emulation Software Accessing the CLI Through the Console PortEntering the Initial Configuration Information IP SettingsCompleting the Setup Program Switch or as a standalone switch Enter an enable secret password, and press ReturnEnter an enable password, and press Return Enter a virtual terminal Telnet password, and press ReturnThese choices appear Numerics Auto-MDIX Pinouts See also connectors and cables cautionsConnectors and cables 10/100 ports Console port Cisco IOS command-line interface CiscoViewConnecting outside the building warning Connection proceduresIN-3 Installing SFP modules 2-17 toConnectors LEDs Running at power on Power Connecting to ACConnecting to DC Power onIN-5 Ground connectionIN-6