Cisco Systems Cisco ME 3400 manual Where to Go Next

Page 48

Chapter 2 Switch Installation

Where to Go Next

Where to Go Next

If the default configuration is satisfactory, the switch does not need further configuration. You can use any of these management options to change the default configuration:

•Use the CLI from the console to configure the switch. See the switch software configuration guide or the switch command reference on for information about using the CLI with a Cisco ME switch.

For setup instructions that use the CLI setup program, go to Appendix D, “Configuring the Switch with the CLI-Based Setup Program.”

•Start an SNMP application such as the CiscoView application.

Cisco ME 3400 Ethernet Access Switch Hardware Installation Guide

2-24	OL-7677-04

Image 48

Contents Americas Headquarters Page N T E N T S Installing and Removing SFP Modules Speed, Duplex, and Autonegotiation IP Settings D-2 Audience PurposeOrganization Conventions Related Publications OL-7677-04 Setting up the Switch Switch Models1describes the switch models Front Panel DescriptionCisco ME 3400-24TS AC and DC Switches Front Panel Cisco ME 3400-24TS AC Ethernet Access Switch Front PanelCisco ME 3400-24FS Switch AC Switch Front Panel Cisco ME 3400G-12CS AC and DC Switches Front PanelCisco ME 3400G-2CS Switch Front Panel System LED Dual-purpose ports Console port SFP module ports10/100 Ports Only the Cisco ME-3400-24TS Switches SFP Module Ports SFP ModulesLEDs SFP Module Patch CableSystem LED These illustrations show the location of the System LEDConsole Power Supply LEDs Only Cisco ME 3400G-12CS Switches Port LEDsConsole Port Dual-Purpose Port LEDsCisco ME 3400-24TS Switch Rear Panel Cisco ME 3400-24FS Switch Rear PanelCable lock Ground connector Fan exhaust Exhaust fan Cable lock Ground connectorPower Supply Features Cisco ME 3400G-12S Switch Rear PanelCisco ME 3400-2CS Switch Rear Panel Fan exhaust AC power connector Ground connectorCisco ME AC Switch Power Supply Cisco ME DC Switch Power SupplyNetwork Configurations Management OptionsPreparing for Installation This section covers these topicsSwitch Installation Preparing for Installation 122F 50C Statement Installation Guidelines Cisco ME 3400-24TS SwitchesCisco ME 3400G-12CS Switches Verifying Switch Operation Installing the SwitchPowering Off the Switch This section describes these installation proceduresRemoving Screws from the Switch Rack-MountingAttaching Brackets to the Switch Rack-Mounting BracketsAttaching Brackets to 19-Inch Racks 191022 Attaching Brackets for 23-Inch Racks Attaching Brackets for 24-Inch Racks Attaching Brackets for Etsi Racks Mounting the Switch in a Rack Phillips machine screws Cable guide and screwAttaching the Brackets to the Switch for Wall-Mounting Wall-MountingPhillips flat-head screws Mounting the Switch on a Wall 11 Mounting the Switch on a WallInstalling and Removing SFP Modules Table- or Shelf-MountingInstalling SFP Modules 12 SFP Module with a Bale-Clasp LatchRemoving SFP Modules Bale claspInserting and Removing the SFP Module Patch Cable Connecting to the 10/100 and 10/100/1000 Ports 17 Connecting to an Ethernet PortConnecting to SFP Modules Connecting to Fiber-Optic SFP ModulesLC connector Connecting to 1000BASE-T SFP Modules 19 Connecting to a 1000BASE-T SFP ModuleConnecting to Dual-Purpose Ports 20 Connecting to a Dual-Purpose PortWhere to Go Next Diagnosing Problems Check Switch Post ResultsThis section includes these troubleshooting topics Check Switch LEDs Check Switch ConnectionsBad or Damaged Cable Ethernet and Fiber CablesSFP Module Port Issues Port and Interface SettingsPing the End Device Spanning Tree LoopsHow to Clear the Switch IP Address and Configuration Check Switch PerformanceSpeed, Duplex, and Autonegotiation Autonegotiation and NIC CardsLocating the Switch Serial Number Serial Number Location on the Cisco ME 3400G-2CS SwitchSerial Number Location on the Cisco ME 3400G-2CS Switch Connector Specifications These sections describe the connectors used with the switch10/100 Ports Figure A-1 10/100 Port Pinouts Figure A-2 Fiber-Optic SFP Module LC Connector Dual-Purpose PortsCable and Adapter Specifications SFP Module Cable SpecificationsTwo Twisted-Pair Cable Pinouts Four Twisted-Pair Cable Pinouts for 1000BASE-T Ports Crossover Cable and Adapter PinoutsIdentifying a Crossover Cable Adapter Pinouts TxD RxDRxD TxD Switch Console RJ-45-to-DB-25 Port DTE Technical Specifications This appendix lists the switch technical specificationsAC Power Requirements Physical Dimensions OL-7677-04 Connecting to DC Power Grounding the Switch Preparing the Ground WireReview these safety warnings before you ground the switch Figure C-1 Stripping the Ground Wire Torque to 15 lbf-in Figure C-3 Torquing Ground-Lug ScrewsConnecting the Grounding Wire to Earth Ground Telco rack Grounding wireTelco rack Wiring the DC-Input Power Source Primary power feed Secondary redundant power feedCisco ME 3400-24TS Switches Cisco ME 3400G-12CS SwitchesAll Cisco ME 3400 Switches Figure C-8 Terminal Block Plug Console Figure C-11 Inserting Wires in the Terminal Block Plug Figure C-13 Completed Wiring of Terminal Block Plug OL-7677-04 Accessing the CLI Through the Console Port Starting the Terminal-Emulation SoftwareEntering the Initial Configuration Information IP SettingsCompleting the Setup Program Enter an enable secret password, and press Return Enter an enable password, and press ReturnEnter a virtual terminal Telnet password, and press Return Switch or as a standalone switchThese choices appear Auto-MDIX Pinouts See also connectors and cables cautions NumericsCisco IOS command-line interface CiscoView Connecting outside the building warningConnection procedures Connectors and cables 10/100 ports Console portInstalling SFP modules 2-17 to IN-3LEDs Running at power on Power Connecting to AC Connecting to DCPower on ConnectorsGround connection IN-5IN-6