Cisco Systems SLM2008RF manual QoS, Statistics

Page 17

Setting Up the Cisco SLM2008 Switch	4
Setting Up the Cisco SLM2008 Switch
Navigating the Utility

•802.1X Settings—Configure security settings that include 802.1X mode, RADIUS IP, Radius UDP port, key string or Admin State authentication mode.

•802.1X Parameter—Enable re-authentication and configure the re- authentication period or EAP timeout.

•Static MAC Address—Allows you to configure a switch port with the MAC address of one or more devices that are authorized to access the network through that port.

•Management Access List—Specifies which Source IP addresses can manage the device.

•Storm Control—Configure the maximum rate (packets per second) at which unknown packets are forwarded.

QoS

This window allows you to priortize network traffic and optimize network performance using Quality of Service (QoS) settings.

•Queue Mode—Set the queue mode priority.

•QoS Mode—Configure the QoS mode settings including QoS disabled, 802.1p, port based, or Differentiated Services Code Point (DSCP).

STP

This window you to configure and view STP settings.

•STP Settings—Configure STP settings including system priority, hello time, max age, and forward delay.

•STP Status—Displays the current STP status.

Statistics

This window displays statistics and IGMP status.

•Statistics Overview—Displays standard statistics on network traffic for each port of the device.

•IGMP Status—Displays the IGMP status for each VLAN interface.

Cisco SLM2008 8-Port Gigabit Smart Switch with PD and AC Power Administration Guide

12

Image 17

Contents Administration Guide OL-19923-01 Connecting the Cisco SLM2008 Switch Introduction Getting to Know the Cisco SLM2008 SwitchSetting Up the Cisco SLM2008 Switch Advanced ConfigurationVlan Appendix a Specifications Appendix B Where to Go From Here Introduction Front Panel, Back Panel, Side Panels, Front PanelSide Panels Getting to Know the Cisco SLM2008 SwitchBack Panel Side Panels Desktop Option Placement OptionsWall-Mount Option Connecting the Cisco SLM2008 SwitchSuggested Mounting Hardware Wall Mounting TemplateConnecting the Cisco SLM2008 Switch to the Network Connecting the Cisco SLM2008 Switch Launching the Web-Based Configuration Utility Setting Up the Cisco SLM2008 SwitchNavigating the Utility Setting Up the Cisco SLM2008 SwitchLogin Window Security SystemPort Statistics QoSMulticast AdminUsing the Help System SetupExample with Help Example with Help Expanded Advanced ConfigurationSystem Configuring System SettingsClick System System Settings Click Save Port Configuring Port SettingsClick Port Port Settings Configuring Static Link Aggregation Click Port Static Link Aggregation Configuring Lacp SettingsClick Port Lacp Settings Click Port Lacp Status Displaying Lacp StatusConfiguring Vlan Settings, Configuring Vlan Port Settings, Configuring Vlan SettingsClick Vlan Vlan Settings Configuring Vlan Port SettingsClick Vlan Vlan Port Settings Security Configuring 802.1X SettingsAdvanced Configuration Click Security 802.1X Settings Configuring 802.1X Parameter Click Security 802.1X Parameter Click Security Static MAC Address Configuring Static MAC AddressClick Security Management Access List Configuring Management Access ListClick Security Storm Control Configuring Storm ControlQoS Configuring QoS SettingsClick QoS QoS Settings QoS Mode Priority Diagram WRR Queue ModeDefault 802.1p Settings 802.1p Value Priority Level 802.1p QoS ModePort-Based QoS Mode All others Dscp Settings Dscp Value PriorityClick STP STP Settings Configuring STP SettingsConfiguring STP Settings, Displaying STP Status, Advanced Configuration STP Bridge Overview Displaying STP StatusClick STP STP Status Displaying Statistics Overview, Displaying Igmp Status, StatisticsSTP Port Status Click Statistics Statistics Overview Displaying Statistics OverviewClick Statistics Igmp Status Displaying Igmp StatusMulticast Configuring Igmp SettingsClick Multicast Igmp Settings Admin Click Admin Ping Configuring PingClick Admin Port Mirror Configuring Port MirrorClick Admin Factory Default Click Restore Default Restoring Factory DefaultClick Admin Reboot Rebooting the SwitchClick Admin Save Configuration Saving Configuration SettingsUpgrading the Firmware Click Admin Firmware UpgradeAdvanced Configuration PoE SpecificationsPerformance LayerOther Management ManagementSecurity AvailabilityEnvironmental StandardsSupport Product ResourcesProduct Documentation Cisco Small BusinessWhere to Go From Here