Cisco Systems SLM2008RF manual Configuring Port Settings

Page 23

Advanced Configuration	5
Advanced Configuration
Port

STEP 4 Reboot the switch by going to the Admin > Reboot window. From there, click Reboot.

Port

This section describes how to configure the port settings of the switch.

•Configuring Port Settings, page 18

•Configuring Static Link Aggregation, page 20

•Configuring LACP Settings, page 21

•Displaying LACP Status, page 23

Configuring Port Settings

You can manually configure the speed, duplex, and flow control settings used on specific ports, or use autonegotiation to allow the switch to autodetect the connection settings used by the attached device. Full-duplex mode should be used on ports whenever possible to double the throughput of switch connections. Flow control should also be enabled to control network traffic during periods of congestion and prevent the loss of packets when port buffer thresholds are exceeded. The switch supports flow control based on the IEEE 802.3x standard.

Cisco SLM2008 8-Port Gigabit Smart Switch with PD and AC Power Administration Guide

18

Image 23

Contents Administration Guide OL-19923-01 Advanced Configuration Introduction Getting to Know the Cisco SLM2008 SwitchConnecting the Cisco SLM2008 Switch Setting Up the Cisco SLM2008 SwitchVlan Appendix a Specifications Appendix B Where to Go From Here Introduction Front Panel, Back Panel, Side Panels, Front PanelSide Panels Getting to Know the Cisco SLM2008 SwitchBack Panel Side Panels Desktop Option Placement OptionsWall Mounting Template Connecting the Cisco SLM2008 SwitchWall-Mount Option Suggested Mounting HardwareConnecting the Cisco SLM2008 Switch to the Network Connecting the Cisco SLM2008 Switch Launching the Web-Based Configuration Utility Setting Up the Cisco SLM2008 SwitchNavigating the Utility Setting Up the Cisco SLM2008 SwitchLogin Window Security SystemPort Statistics QoSMulticast AdminUsing the Help System SetupExample with Help Example with Help Expanded Advanced ConfigurationSystem Configuring System SettingsClick System System Settings Click Save Port Configuring Port SettingsClick Port Port Settings Configuring Static Link Aggregation Click Port Static Link Aggregation Configuring Lacp SettingsClick Port Lacp Settings Click Port Lacp Status Displaying Lacp StatusConfiguring Vlan Settings, Configuring Vlan Port Settings, Configuring Vlan SettingsClick Vlan Vlan Settings Configuring Vlan Port SettingsClick Vlan Vlan Port Settings Security Configuring 802.1X SettingsAdvanced Configuration Click Security 802.1X Settings Configuring 802.1X Parameter Click Security 802.1X Parameter Click Security Static MAC Address Configuring Static MAC AddressClick Security Management Access List Configuring Management Access ListClick Security Storm Control Configuring Storm ControlQoS Configuring QoS SettingsClick QoS QoS Settings QoS Mode Priority Diagram WRR Queue ModeDefault 802.1p Settings 802.1p Value Priority Level 802.1p QoS ModePort-Based QoS Mode All others Dscp Settings Dscp Value PriorityClick STP STP Settings Configuring STP SettingsConfiguring STP Settings, Displaying STP Status, Advanced Configuration STP Bridge Overview Displaying STP StatusClick STP STP Status Displaying Statistics Overview, Displaying Igmp Status, StatisticsSTP Port Status Click Statistics Statistics Overview Displaying Statistics OverviewClick Statistics Igmp Status Displaying Igmp StatusMulticast Configuring Igmp SettingsClick Multicast Igmp Settings Admin Click Admin Ping Configuring PingClick Admin Port Mirror Configuring Port MirrorClick Admin Factory Default Click Restore Default Restoring Factory DefaultClick Admin Reboot Rebooting the SwitchClick Admin Save Configuration Saving Configuration SettingsUpgrading the Firmware Click Admin Firmware UpgradeAdvanced Configuration Layer SpecificationsPoE PerformanceAvailability ManagementOther Management SecurityEnvironmental StandardsCisco Small Business Product ResourcesSupport Product DocumentationWhere to Go From Here