Cisco Systems OL-19806-03 manual Using the Call In-Progress Feature

Page 20

Chapter 1 Managing Single Entities

Using the Call In-Progress Feature

Using the Call In-Progress Feature

Use this feature, also referred to as activity check, to configure the switch to wait until a Cisco IP phone connected to a PoE port is not sending or receiving traffic before powering off the port.

Use the energywise activitycheck interface configuration command on these Cisco devices:

•Catalyst 6500 switches (see the Cisco IOS Release Notes for Cisco EnergyWise, EnergyWise Phase 2 for the specific devices)

•Catalyst 4500 switches

Note Before powering off a PoE port, Catalyst 6500 and Catalyst 4500 switches use interface statistics to determine when a Cisco IP phone connected to the PoE port is not sending or receiving traffic.

•Catalyst 3750-X, 3750-E, 3750, 3560-X, 3650-E, 3560, and 2960 switches

•Cisco EtherSwitch service modules (NME-16ES-1G, NME-16ES-1G-P, NME-X-23ES-1G, NME-X-23ES-1G-P, NME-XD-24ES-1S-P, NME-XD-48ES-2S-P)

•Cisco enhanced EtherSwitch service modules (SM-D-ES2-48, SM-D-ES3-48-P, SM-D-ES3G-48-P, SM-ES2-16-P, SM-ES2-24, SM-ES2-24-P, SM-ES3-16-P, SM-ES3-24-P, SM-ES3G-16-P, SM-ES3G-24-P)

Before entering the energywise activitycheck command on devices other than Catalyst 6500 and 4500 switches, you must enable automatic quality of service (auto-QoS) for VoIP on the port with this configuration:

•All packets from the IP phone have the class of service (CoS) value 5.

To verify this, use the show mls qos maps cos-output-qprivileged EXEC command to display the CoS output queue threshold map.

This example shows that CoS value 5 is mapped to queue 1 and threshold 3 on the Gigabit

Ethernet 0/1:

Cos-outputq-threshold map:

cos: 0 1 2 3 4 5 6 7

------------------------------------

queue-threshold: 4-3 4-2 3-3 2-3 3-3 1-3 2-3 2-3

This is the configuration for the PoE port:

<output truncated>

interface GigabitEthernet0/1 srr-queue bandwidth share 10 10 60 20 queue-set 2

priority-queue out

mls qos trust device cisco-phone mls qos trust cos

auto qos voip cisco-phone

service-policy input AutoQoS-Police-CiscoPhone <output truncated>

•Auto-QoS for VoIP is enabled on the PoE port.

•Auto-QoS is enabled on the IP phone. The switch does not change the CoS value in the packet from the IP phone.

	Cisco EnergyWise Configuration Guide
1-12	OL-19806-03

Image 20

Contents Cisco EnergyWise Configuration Guide Americas HeadquartersCisco EnergyWise Configuration Guide N T E N T S Important Notice C-1 Conventions AudiencePurpose Preface Related Publications For information about the Cisco network devices, seeObtaining Documentation, Support, and Security Guidelines Managing Single Entities Overview Network management stations Domain membersCreating an EnergyWise Domain Power Levels Category Level DescriptionDefinition Defaults AttributesRecurring Event Secure Domain CommunicationMIBs Switch Connected to an IP Phone Management station Domain member Switch Connected to a PC Switch and PC ScenarioConfiguration Guidelines Cisco EnergyWise Configuration Guide Using the Call In-Progress Feature This is the configuration for the PoE portEnergyWise Entity PoE Mode Auto Never Static PoE and EnergyWise InteractionsPreventing Network Access to a Non-Cisco End Point CLI Compatibility Issues PC without Access to the EnergyWise Network and the InternetManually Managing Power Enabling EnergyWise, Configuring Entity Attributes,Command Purpose Shared-secret 0 7 mgmt-password port Energywise importance importanceEnergywise keywords word,word Energywise management securityEnergywise name name Energywise neighbor hostname ip-addressEnergywise role role Energywise allow query save setCopy running-config startup-config Interface interface-idEnergywise level level Show energywise childrenEnergywise name name Energywise role roleConfiguring Recurring Events Show running-configEnergywise activitycheck Energywise allow query setMonday , Tuesday , Wednesday , Thursday , Friday Show energywise recurrence Copy running-config startup-configEnergywise level level recurrence importance Disabling EnergyWise Command Mode PurposeDayofmonth month Dayofweek timerange To power on the lab IP phones ExamplesAutomatically Managing Power To power off anIP phone connected to a PoE portIf the time range has end times and days such as Pc-mgrManaging Multiple Entities Running QueriesManaging Multiple Entities Running Queries Multiple Switches Connected to Multiple End Points Management station End point Domain memberUsing Queries to Manage Power in the Domain Delta usage timeout timeoutEnergywise query importance importance Keywords word,word, ... name name collectOptional Runs a query to power on or off the domain members Keywords word,word, ... name name set levelQuerying with the Name Attribute Setting the Time-Out Value Verify the power levelsOL-19806-03 EnergyWise CLI Commands Clear energywise neighbors Debug energywise Debug energywise endpoint managementEndpoint ManagementEnergywise global configuration Domain member, configures the switch toSave-Responds to a query to save the running configuration Energywise allow query save setLevel level Name nameNeighbor hostname Role roleAllow query save set keywords were added Neighbors are not assigned Role is the model numberKeywords Management passwords Energywise interface configuration No energywise domainActivitycheck Allow query setKeywords word,word RecurrenceImportance importance Time-rangeUdp port Command Default Command Modes Command HistorySecurity Absolute Command Description Energywise domain SecurityNtp-shared-secret Protocol udp portUsage Guidelines Examples Command Modes Command HistoryRelated Commands Description Collect delta usage Timeout timeoutEnergywise query Set level level Sum delta usageMembers and end points Delta-Display the delta vectorSwitch# energywise query importance 90 name * collect delta These examples show how to filter results with keywords Switch# energywise query importance 90 name * set levelSnmp-server enable traps energywise Event-occuredLevel-change Neighbor-addedTo send EnergyWise traps to the NMS To send only EnergyWise event traps to the NMSShow energywise Switch# show energywise children Domain Cisco Protocol Statistics Energywise global configuration Enables and configures EnergyWise on the entityEnergywise interface configuration Configures EnergyWise on the PoE portOL-19806-03 Using CLI Commands Verifying the Power Usage Cisco EnergyWise and Catalyst 4500 Switches OL-19806-03 Cisco EnergyWise and Catalyst 6500 Switches OL-19806-03 Important Notice DisclaimerCisco EnergyWise Configuration Guide Statement 1071-Warning Definition Bewaar Deze InstructiesWarnung Wichtige Sicherheitshinweise Avvertenza Importanti Istruzioni Sulla SicurezzaAviso Instruções Importantes DE Segurança Guarde Estas InstruçõesGEM Disse Anvisninger Page OL-19806-03