Cisco Systems 3750-E, 3560-E manual Preparing for Installation, Safety Warnings

Page 31

C H A P T E R 2

Switch Installation

This chapter describes how to install a Catalyst 3750-E or a Catalyst 3560-E switch and make connections to the switch. It also includes planning and cabling considerations for stacking switches (only Catalyst 3750-E switches). Read the topics and perform the procedures in this order:

•Preparing for Installation, page 2-1

•Planning a Switch Stack (Catalyst 3750-E Switches), page 2-6

•Installing the Switch, page 2-10

•Connecting to the StackWise Ports (Catalyst 3750-E Switches), page 2-19

•Installing Devices in the 10-Gigabit Ethernet Slots, page 2-20

•Installing SFP Modules, page 2-23

•Connecting Devices to the Ethernet Ports, page 2-26

•Where to Go Next, page 2-29

For initial switch setup, how to assign the switch IP address, and for powering information, see the switch getting started guide on Cisco.com.

Preparing for Installation

This section covers these topics:

•Safety Warnings, page 2-1

•Installation Guidelines, page 2-5

•Box Contents, page 2-5

•Tools and Equipment, page 2-5

Safety Warnings

This section includes the basic installation caution and warning statements. Translations of the warning statements appear in the Regulatory Compliance and Safety Information for the Catalyst 3750-E and Catalyst 3560-E Switch document that shipped with the switch and online at Cisco.com. Read this section before you start the installation procedure.

Catalyst 3750-E and Catalyst 3560-E Switch Hardware Installation Guide

	OL-9774-03	2-1

Image 31

Contents Text Part Number OL-9774-03 Americas HeadquartersPage N T E N T S Connecting Devices to the Ethernet Ports Wiring the DC-Input Power Source Accessing the CLI Through the Console Port C-1 Purpose AudienceConventions Viii Related PublicationsPreface OL-9774-03 Part Number Description Switch ModelsFront Panel Description Switch Part Number Description24- and 48-Port Switch Front Panel PoE Ports 10/100/1000 Ethernet PortsSFP Modules Gigabit Ethernet Module SlotsCisco TwinGig Converter Module LEDs 24- and 48-Port Switch LEDsColor System Status System LEDColor Power Supply LEDsMaster LED Color RPS StatusFan LED Mode LED Port Mode DescriptionPort LEDs and Modes Port Mode Port LED Color Meaning Color PoE Status PoE LEDStack LED Stack LEDRear Panel Description 24- and 48-Port Switch Rear PanelStackWise Ports Catalyst 3560E-12D Switch Rear PanelPort PoE Port non-PoE Port Non-PoE Power-Supply Modules48-Port Switch Power-Supply Modules SwitchDC-Power-Supply Module LEDs Description AC-Power-Supply Module LEDsModule LEDs Description Fan Modules Management Ports RPS ConnectorManagement Options Network Configurations Safety Warnings Preparing for InstallationOL-9774-03 Switch Installation Preparing for Installation Statement 371-Power Cable and AC Adapter Box Contents Installation GuidelinesTools and Equipment Switch Stacking Guidelines Planning a Switch Stack Catalyst 3750-E SwitchesStack Cabling Configurations Example of a Stack with Full Bandwidth Connections Stack Bandwidth and Partitioning ExamplesExample of a Stack with a Failover Condition Power On Sequence for Switch StacksRack-Mounting Installing the SwitchRack-Mounting Brackets Attaching the Rack-Mount Brackets 10 Removing Screws from the Switch11 Attaching Brackets for 19-inch Racks Mounting the Switch in a Rack Mounting the Switch in a RackWall-Mounting Attaching the Brackets to the Switch for Wall-MountingMounting the Catalyst 3560E-12D Switch on a Wall Mounting the Catalyst 3560E-12SD Switch on a Wall Table- or Shelf-Mounting After Installing the SwitchConnecting to the StackWise Ports Catalyst 3750-E Switches Installing X2 Transceiver Modules and Converter Modules Installing Devices in the 10-Gigabit Ethernet SlotsModule inserted face up Module inserted face down 202046 Removing an X2 Transceiver Module or Converter Module Installing SFP ModulesInstalling an SFP Module Lower SFP modules are inverted on 24- and 48-port switches Removing an SFP Module Connecting Devices to the Ethernet PortsPoE Port Connections 10/100/1000 Ethernet Port ConnectionsDevice Crossover Cable Switch Installation Connecting Devices to the Ethernet Ports Where to Go Next OL-9774-03 Installation Overview Power Supply and Fan Module InstallationOL-9774-03 Inserting the AC-Power Supply in 24- and 48-Port Switches Installing an AC-Power SupplyAC-Power Supply with Power Cord Retainer Installing a DC-Power SupplyGrounding the Switch Preparing for InstallationStripping the Ground Wire See -9for the Catalyst 3560E-12SD ground location Inserting the DC-Power Supply in 24- and 48-Port Switches Installing the DC Power Supply in the SwitchWiring the DC-Input Power Source 12 Inserting the Fan Module in 24- and 48-Port Switches Installing a Fan Module202049 OL-9774-03 Check Switch Post Results Diagnosing ProblemsEthernet and Fiber Cables Check Switch LEDsCheck Switch Connections Bad or Damaged CablePort and Interface Settings Transceiver IssuesPoE Connections Speed, Duplex, and Autonegotiation Check Switch PerformancePing End Device Spanning Tree LoopsAutonegotiation and NIC Cards How to Clear the Switch IP Address and ConfigurationCabling Distance How to Replace a Failed Stack Member Finding the Switch Serial NumberTroubleshooting How to Replace a Failed Stack Member OL-9774-03 Environmental Ranges Physical SpecificationsPower Specifications Table A-5 OL-9774-03 Connector Specifications Connector and Cable SpecificationsGigabit Ethernet Module Interfaces 10/100/1000 PortsFigure B-4 Duplex LC Cable Connector Console Port 10/100 Ethernet Management PortMicrons MHz/km Cable and Adapter SpecificationsGigabit Ethernet X2 Transceiver Module Cable Specifications Modal X2 Product Wavelength Core Size Bandwidth NumberDBm Wavelength nm SFP Module Cable SpecificationsX2 Product Transmit Power Receive Power Number Transmit652 43.4 to 62 miles 1530 To 100 km 1570 1610 Four Twisted-Pair Cable PinoutsTwo Twisted-Pair Cable Pinouts Two Twisted-Pair Crossover Cable SchematicDevice Switch Console RJ-45-to-DB-9 Port DTEIdentifying a Crossover Cable Console Port Adapter PinoutsSwitch Console RJ-45-to-DB-25 Port DTE Accessing the CLI Through Express Setup Accessing the CLIAccessing the CLI Through the Console Port IP Settings Entering the Initial Configuration InformationConnecting to the Console Port Completing the Setup Program Line vty 0 These choices appear OL-9774-03 Numerics IN-2 IN-3 IN-4 IN-5 IN-6

Related manuals

Manual 20 pages 4.95 Kb