Cisco Systems 12406, 12006 manual Dc Pdu

Page 33

Chapter 3 Installing the Router

Connecting to a DC Power Source

Figure 3-19

DC PDU

1

POWER B

+

GND

3

5

4

6

2

POWER A

+ GND

57992

1	Captive screws (four)	4	DC PDU

2	DC power connector block (A)	5	Guide pin

3	DC power connector block (B)	6	Blower module connector

To connect source DC power to the DC PDU, see Figure 3-19and Figure 3-20and follow these steps:

Step 1 Attach an ESD-preventive strap to your wrist and connect the leash to the chassis or to another grounded, bare metal surface.

Step 2 Locate the DC PDU on the back of the router. The PDU is positioned directly below and behind the blower module.

		Cisco 12006 and Cisco 12406 Router Installation and Configuration Guide

	OL-11497-03			3-33
	OL-11497-03			3-33

Image 33

Contents Installing the Router Installing a Router Installing the Rack-Mount Brackets Optional Installing the Optional Rack-Mount BracketsTools and Equipment Required Installing the Optional Rack-Mount Brackets Lower and Upper Center-Mount Brackets Installing Center-Mount Brackets OptionalRepeat through for both upper center-mount brackets Installing the Optional Center-Mount BracketsPower supply Installing the Chassis in a RackOL-11497-03 Supplemental Bonding and Grounding Connections Installing the Chassis on a Tabletop or Flat SurfaceSupplemental Bonding and Grounding Port for Nebs Compliance Crimping the Lug Connecting RP and Line Card CablesChassis Cable-Management Bracket Connecting Alarm Card Cables GRP Console and Auxiliary Ports Connecting to the Console and Auxiliary PortsGRP Console DCE and Auxiliary DTE Port Connections GRP Console Port Signals GRP Auxiliary Port SignalsPin Signal Input/Output Description RTS PRP Console and Auxiliary Port Connections PRP Console and Auxiliary PortsConsole Port Pin Signal Input/Output Description PRP Console Port SignalsInstalling a Flash Memory Card PRP Auxiliary Port SignalsAuxiliary Port Pin Signal 10 Flash Memory Card Slot Opening 11 RJ-45 and MII Ethernet Connections Connecting the GRP to an Ethernet NetworkMDC Pin1 Out Input/Output Description CodePin Pin Out Input/Output Description CodePin Signal Connecting the PRP to an Ethernet Network14 Using the Ethernet Port on the PRP PRP Ethernet Connections Ethernet Port Pin Signal DescriptionCrossover Cable Pinout for Connecting Two PRPs Connecting to an AC Power Source Parameter RJ-45Parameter Router Power Combination 18 AC Power Distribution Unit Connecting to a DC Power Source DC PDU Power a Power On the Router Alarm Cisco IOS Software Images IOS Software Configuration for the RouterConditions to Check Before System Startup Starting the Router and Observing Initial Conditions Overview of the Boot ProcessOL-11497-03 Display Meaning Source RP Alphanumeric LEDRP Interfaces Using the RP LEDs GRP Interfaces Using the GRP LEDs PRP Interfaces Using the PRP LEDs ETH External Network Interface System Configuration DialogueDir bootflash Manually Booting the SystemLocating a Valid Cisco IOS Software Image Dir slot0Command Description Booting from the Cisco IOS Software ImageRouter Configuration Setup CommandBefore You Begin User Interface Command Modes Global Configuration ModeCisco IOS User Interface Privileged Exec Mode User Exec ModeInterface Configuration Mode Subinterface Configuration ModeROM Monitor Mode Configuration Changes Setup Command Interactive Script Example SDCC1/0 Configuring interface POS1/0 Is this interface in use?yes Configuring Global Parameters PasswordsHost Name Protocols Configuring Network InterfacesPRP Ethernet Interfaces GRP Ethernet InterfacesLine Card Interfaces Show version Command Checking the Software VersionRouter# show version Verifying the Running Configuration Settings Show running Config Command ExampleRouter# show running-config No service tcp-small-servers Hostname Router Reviewing the Running Configuration Settings Saving the Running Configuration Settings to NvramShow startup-config Command Router# copy running-config startup-configNo logging trap Installing the Flash Memory Card in a RP Using Flash Memory Cards in the RPFormatting a Flash Memory Card Removing the Flash Memory Card from an RPSpecify a Boot Image Router# configure terminalRouter# format slot0 Router# cd slot1 Flash Memory Console CommandsRouter# delete slot0info Router# cd bootflashRouter# squeeze slot0 Routerconfig# boot system flash devicefilename Booting from Flash MemoryRouterconfig# config-reg Ctrl-Z Copying FilesRouter# copy tftpmyfile1 slot0myfile1 Router# copy tftpfilename bootflashslot0slot1 filenameRouter# copy tftpnew.image slot0new.image Copying a Cisco IOS Software ImageCopying Cisco IOS Software Updates Router# copy slot1image.new slot0image.new Copying Files Between RP Memory and a Flash Memory Card Copy startup-config slot0 slot1filename Router# show bootvarRouter# dir slot0 Router# copy startup-config slot0myfile2Router# copy running-config slot0myfile2 Copy running-config slot0slot1filenameCopy slot0slot1filename startup-config Router# copy slot0myfile startup-configRouter# copy startup-config running-config Locked Blocks in Flash Memory Cards If You Need More InformationInstalling the Router If You Need More Information OL-11497-03