Cisco Systems 12406, 12006 IOS Software Configuration for the Router, Cisco IOS Software Images

Page 37

Chapter 3 Installing the Router

IOS Software Configuration for the Router

Step 6 On the console terminal, verify that the console displays the system banner and that the system and all interfaces initialize successfully.

If the power modules do not power up, or if the system or any interfaces do not initialize properly, see Chapter 4, “Troubleshooting the Installation.” If you are still unable to resolve the problem, contact your Cisco service representative for assistance.

IOS Software Configuration for the Router

This section explains how to configure your system so that it can access the network or enable other hosts on the network to access your system remotely by means of a Telnet connection. You can find more information in the configuration publications listed in the “If You Need More Information” section on page 3-82.

The system startup process and a procedure for performing a basic configuration of your router are presented in the following sections:

•Cisco IOS Software Images, page 3-37

•Conditions to Check Before System Startup, page 3-38

•Overview of the Boot Process, page 3-39

•Starting the Router and Observing Initial Conditions, page 3-39

•Manually Booting the System, page 3-47

•Router Configuration, page 3-49

Cisco IOS Software Images

A default Cisco IOS software image for your system is available through any of the internal or external sources described in Table 3-11.

		Cisco 12006 and Cisco 12406 Router Installation and Configuration Guide

	OL-11497-03			3-37
	OL-11497-03			3-37

Image 37

Contents Installing the Router Installing a Router Installing the Optional Rack-Mount Brackets Installing the Rack-Mount Brackets OptionalTools and Equipment Required Installing the Optional Rack-Mount Brackets Lower and Upper Center-Mount Brackets Installing Center-Mount Brackets OptionalRepeat through for both upper center-mount brackets Installing the Optional Center-Mount BracketsPower supply Installing the Chassis in a RackOL-11497-03 Supplemental Bonding and Grounding Connections Installing the Chassis on a Tabletop or Flat SurfaceSupplemental Bonding and Grounding Port for Nebs Compliance Crimping the Lug Connecting RP and Line Card CablesChassis Cable-Management Bracket Connecting Alarm Card Cables GRP Console and Auxiliary Ports Connecting to the Console and Auxiliary PortsGRP Console DCE and Auxiliary DTE Port Connections GRP Auxiliary Port Signals GRP Console Port SignalsPin Signal Input/Output Description RTS PRP Console and Auxiliary Port Connections PRP Console and Auxiliary PortsConsole Port Pin Signal Input/Output Description PRP Console Port SignalsPRP Auxiliary Port Signals Installing a Flash Memory CardAuxiliary Port Pin Signal 10 Flash Memory Card Slot Opening 11 RJ-45 and MII Ethernet Connections Connecting the GRP to an Ethernet NetworkMDC Pin1 Out Input/Output Description CodePin Pin Out Input/Output Description CodePin Signal Connecting the PRP to an Ethernet Network14 Using the Ethernet Port on the PRP PRP Ethernet Connections Ethernet Port Pin Signal DescriptionCrossover Cable Pinout for Connecting Two PRPs Parameter RJ-45 Connecting to an AC Power SourceParameter Router Power Combination 18 AC Power Distribution Unit Connecting to a DC Power Source DC PDU Power a Power On the Router Alarm Cisco IOS Software Images IOS Software Configuration for the RouterConditions to Check Before System Startup Starting the Router and Observing Initial Conditions Overview of the Boot ProcessOL-11497-03 Display Meaning Source RP Alphanumeric LEDRP Interfaces Using the RP LEDs GRP Interfaces Using the GRP LEDs PRP Interfaces Using the PRP LEDs ETH External Network Interface System Configuration DialogueDir bootflash Manually Booting the SystemLocating a Valid Cisco IOS Software Image Dir slot0Command Description Booting from the Cisco IOS Software ImageSetup Command Router ConfigurationBefore You Begin Global Configuration Mode User Interface Command ModesCisco IOS User Interface Privileged Exec Mode User Exec ModeSubinterface Configuration Mode Interface Configuration ModeROM Monitor Mode Configuration Changes Setup Command Interactive Script Example SDCC1/0 Configuring interface POS1/0 Is this interface in use?yes Passwords Configuring Global ParametersHost Name Protocols Configuring Network InterfacesPRP Ethernet Interfaces GRP Ethernet InterfacesLine Card Interfaces Checking the Software Version Show version CommandRouter# show version Show running Config Command Example Verifying the Running Configuration SettingsRouter# show running-config No service tcp-small-servers Hostname Router Reviewing the Running Configuration Settings Saving the Running Configuration Settings to NvramShow startup-config Command Router# copy running-config startup-configNo logging trap Installing the Flash Memory Card in a RP Using Flash Memory Cards in the RPFormatting a Flash Memory Card Removing the Flash Memory Card from an RPRouter# configure terminal Specify a Boot ImageRouter# format slot0 Router# cd slot1 Flash Memory Console CommandsRouter# delete slot0info Router# cd bootflashRouter# squeeze slot0 Routerconfig# boot system flash devicefilename Booting from Flash MemoryRouterconfig# config-reg Ctrl-Z Copying FilesRouter# copy tftpmyfile1 slot0myfile1 Router# copy tftpfilename bootflashslot0slot1 filenameRouter# copy tftpnew.image slot0new.image Copying a Cisco IOS Software ImageCopying Cisco IOS Software Updates Router# copy slot1image.new slot0image.new Copying Files Between RP Memory and a Flash Memory Card Copy startup-config slot0 slot1filename Router# show bootvarRouter# dir slot0 Router# copy startup-config slot0myfile2Router# copy running-config slot0myfile2 Copy running-config slot0slot1filenameRouter# copy slot0myfile startup-config Copy slot0slot1filename startup-configRouter# copy startup-config running-config Locked Blocks in Flash Memory Cards If You Need More InformationInstalling the Router If You Need More Information OL-11497-03